Engineering topics

Kennedy, F. E.

Publications and source records attributed to Kennedy, F. E..

11 records

NASA NTRS1993

XPS analysis of the effect of fillers on PTFE transfer film development in sliding contacts

The development of transfer films atop steel counterfaces in contact with unfilled and bronze-filled PTFE has been studied using X-ray photoelectron spectroscopy. The sliding apparatus was contained within the vacuum of the analytical system, so the effects of the native oxide, hydrocarbon, and adsorbed gaseous surface layers of the steel upon the PTFE transfer behavior could be studied in situ. For both the filled and the unfilled PTFE, cleaner surfaces promoted greater amounts of transfer. Metal fluorides, which formed at the transfer film/counterface interface, were found solely in cases where the native oxide had been removed to expose the metallic surface prior to sliding. These fluorides also were found at clean metal/PTFE interfaces formed in the absence of frictional contact. A fraction of these fluorides resulted from irradiation damage inherent in XPS analysis. PTFE transfer films were found to build up with repeated sliding passes, by a process in which strands of transfer filled in the remaining counterface area. Under these reported test conditions, the transfer process is not expected to continue atop previously deposited transfer films. The bronze-filled composite generated greater amounts of transfer than the unfilled PTFE. The results are discussed relative to the observed increase in wear resistance imparted to PTFE by a broad range of inorganic fillers.

Blanchet, T. A.↗

NASA NTRS1985

An experimental investigation of rubbing interaction in labyrinth seals at cryogenic temperature

An experimental program was carried out to address issues related to the observed cracking of the titanium knife edges on the labyrinth seals of the high pressure fuel pump (HPFP) in the Space Shuttle main engine (SSME). Thermal shock experiments were carried out using a jet specimen with geometry similar to the knife edge geometry. These tests demonstrate that cracking of the titanium alloy is possible in a situation involving repeated thermal cycles over a wide temperature range, as might be realized during a rub in the liquid hydrogen fuel pump. High speed rub interaction tests were conducted using a representative knife edge and seal geometry over a broad range of interaction rates. Alternative materials were also experimentally evaluated. These tests provide information which can be used to design improved labyrinth seals for the HPFP of the SSME. In particular, plasma-sprayed aluminum-graphite was found to be significantly better than aluminum alloy seals used at present from the standpoint of rub performance. Ion nitriding of the titanium alloy knife edges was also found to improve rub performance compared with the untreated baseline knife edge material.

Dolan, F. X.↗

NASA NTRS1985

The role of near-surface plastic deformation in the wear of lamellar solids

It is shown in this paper that the role of surface and near-surface plastic deformation is especially significant in both sliding and abrasive wear of lamellar composites. Lamellar structures were produced artificially from alternate layers of pure copper and pure tin or lead foils. The resulting composites were tested in three different wear tests: single-pass abrasion by a sharp, hard abrader; multiple-pass rubbing by a hard, rounded abrader; and pin-on-disk sliding. In each case the counterface was a hard alloy steel. Tests were run with the composite lamellae in two orientations: perpendicular and parallel to the sliding direction. It was found that the composites had much less wear resistance and greater abradability when oriented perpendicular to the rub direction. The mechanisms for wear particle removal and the role of plastic deformation in the process were studied by plasticity analysis and by microscopic (SEM and optical) observation.

Kennedy, F. E.↗

NASA NTRS1984

Analytical and experimental investigation of rubbing interaction in labyrinth seals for a liquid hydrogen fuel pump

Cracking of the titanium knife edges on the labyrinth seals of the liquid hydrogen fuel pump in the Space Shuttle main engine is considered. Finite element analysis of the thermal response of the knife edge in sliding contact with the wear ring surface shows that interfacial temperatures can be quite high and they are significantly influenced by the thermal conductivity of the surfaces in rubbing contact. Thermal shock experiments on a test specimen similar to the knife edge geometry demonstrate that cracking of the titanium alloy is possible in a situation involving repeated thermal cycles over a wide temperature range, as might be realized during a rub in the liquid hydrogen fuel pump. High-speed rub interaction tests were conducted using a representative knife edge and seal geometry over a broad range of interaction rates and alternate materials were experimentally evaluated. Plasma-sprayed aluminum-graphite was found to be significantly better than presently used aluminum alloy seals from the standpoint of rub performance. Ion nitriding the titanium alloy knife-edges also improved rub performance compared to the untreated baseline.

Dolan, F. X.↗

NASA NTRS1981

Single pass rub phenomena - Analysis and experiment

An experimental and analytical investigation is presented of contact phenomena for the case of a fully-dense copper gas path seal segment which is rubbed by a single steel blade tip at room temperature. The experiments were executed on a pendulum-type test device, with forces, rub energy, surface temperature and residual deformation being determined for each single-path rub test. The thermal and mechanical factors influencing single-pass rub surface temperatures were modeled analytically. It is found that large plastic strains occurred on or near the contact surface of the copper rub specimens. A study of the influence of various material properties on surface temperature showed that increased thermal conductivity of the stationary component played a role in lowering contact temperatures. Increased thermal conductivity of the moving blade tip component and increased thermal diffusivity of the stationary material also had a beneficial effect.

Kennedy, F. E.↗

NASA NTRS1981

Single-pass rub testing of abradable seal materials

A pendulum-type test device has been built for use in studying rubs between a turbine or compressor blade tip or labyrinth seal knife edge and specimens of abradable gas path seal materials. The device allows measurement of the rub energy dissipated in a single wear event, along with friction and normal forces and wear. Subsequent rubs over the same surface can also be monitored, with microscopic observation of the rub surface being possible after any of the passes. The device was used in tests of several potential abradable materials, ranging from porous to fully dense. It was shown that the rub energy dissipated in initial and subsequent passes is a fundamental parameter in the evaluation of material abradability. Rub energy was found to be influenced by such factors as: density and tensile (or yield) strength of the abradable material, prior densification or work hardening of the rub surface, and the sharpness of the leading edge of the blade tip.

Kennedy, F. E.↗

NASA NTRS1980

Thermomechanical phenomena in high speed rubbing

An analytical approach is presented for the modeling of the thermomechanical interactions which occur in high speed sliding situations. These sliding contact problems which are characterized by active and interrelated thermal and mechanical phenomena could be called 'rub energetics' problems. Analytical models were developed to simulate two different rub situations: high energy braking of disk brakes and high speed rubs of gas path seals in turbine engines. The models proved to be particularly useful in predicting the severe temperatures and deformations near hot contact patches on the rubbing surfaces. The size of the hot patches is generally determined by normal load and the properties of the contacting materials. Temperatures at the contact patches can approach the melting point of the materials, especially at high sliding velocities. These high temperatures can lead to large amounts of near-surface deformation and high wear rates. Decreased contact temperatures can result from using materials with increased thermal conductivity and increased heat capacity or choosing mechanical properties (decreased stiffness, yield stress or coefficient of thermal expansion) which give larger hot spot size.

Kennedy, F. E.↗

NASA NTRS1979

Thermal stress analysis of ceramic gas-path seal components for aircraft turbines

Stress and temperature distributions were evaluated numerically for a blade-tip seal system proposed for gas turbine applications. The seal consists of an abradable ceramic layer on metallic backing with intermediate layers between the ceramic layer and metal substrate. The most severe stresses in the seal, as far as failure is concerned, are tensile stresses at the top of the ceramic layer and shear and normal stresses at the layer interfaces. All these stresses reach their maximum values during the deceleration phase of a test engine cycle. A parametric study was carried out to evaluate the influence of various design parameters on these critical stress values. The influences of material properties and geometric parameters of the ceramic, intermediate, and backing layers were investigated. After the parametric study was completed, a seal system was designed which incorporated materials with beneficial elastic and thermal properties in each layer of the seal. An analysis of the proposed seal design shows an appreciable decrease in the magnitude of the maximum critical stresses over those obtained with earlier configurations.

Kennedy, F. E.↗

NASA NTRS1977

Evaluation of aircraft brake materials

A test program was carried out to evaluate several new high-temperature friction materials for use in aircraft disk brakes. A specially built test apparatus utilizing a disk brake and wheel half from a small jet aircraft was used. The apparatus enabled control of brake pressure, velocity and braking time. Tests were run under both constant and variable velocity conditions and covered a kinetic energy range similar to that encountered in aircraft brake service. The materials evaluation showed that two newly developed friction materials show potential for use in aircraft disk brakes. One of the materials is a nickel-based sintered composite, while the other is a molybdenum-based material. Both materials show much lower wear rates than conventional copper-based materials and are better able to withstand the high temperatures encountered during braking. Additional materials improvement is necessary, however, since both materials show a significant negative slope of the friction-velocity curve at low velocities.

Ho, T. L.↗

NASA NTRS1976

Effect of design factors on surface temperature and wear in disk brakes

The temperatures, friction, wear and contact conditions that occur in high energy disk brakes are studied. Surface and near surface temperatures were monitored at various locations in a caliper disk brake during drag type testing, with friction coefficient and wear rates also being determined. The recorded transient temperature distributions in the friction pads and infrared photographs of the rotor disk surface both showed that contact at the friction surface was not uniform, with contact areas constantly shifting due to nonuniform thermal expansion and wear. The effect of external cooling and of design modifications on friction, wear and temperatures was also investigated. It was found that significant decreases in surface temperature and in wear rate can be achieved without a reduction in friction either by slotting the contacting face of the brake pad or by modifying the design of the pad support to improve pad compliance. Both design changes result in more uniform contact conditions on the friction surface.

Santini, J. J.↗

NASA NTRS1975

Evaluation of materials and design modifications for aircraft brakes

A test program is described which was carried out to evaluate several proposed design modifications and several high-temperature friction materials for use in aircraft disk brakes. The evaluation program was carried out on a specially built test apparatus utilizing a disk brake and wheel half from a small het aircraft. The apparatus enabled control of brake pressure, velocity, and braking time. Tests were run under both constant and variable velocity conditions and covered a kinetic energy range similar to that encountered in aircraft brake service. The results of the design evaluation program showed that some improvement in brake performance can be realized by making design changes in the components of the brake containing friction material. The materials evaluation showed that two friction materials show potential for use in aircraft disk brakes. One of the materials is a nickel-based sintered composite, while the other is a molybdenum-based material. Both materials show much lower wear rates than conventional copper-based materials and are better able to withstand the high temperatures encountered during braking. Additional materials improvement is necessary since both materials show a significant negative slope of the friction-velocity curve at low velocities.

Ho, T. L.↗