Engineering topics

Kendall, J. M.

Publications and source records attributed to Kendall, J. M..

At least 19 records

NASA NTRS2007

Boundary Layer Receptivity to Weak Freestream Turbulence

The experimental configuration is shown. The tunnel is about 8 ft. long by 2 ft. square. In most cases the wind speed is set to 11.6 m/s. Three different plates are used. Each is a quarter-inch thick, extends wall-to-wall, and has a semi-elliptical leading edge. The two extremes in bluntness are shown, being half a 14:1 ellipse and half a 5:1 ellipse. The plate surface pressure is uniform to better than 0.01 q, except near the leading edge, or whenever a condition of lift is intentionally applied to the plate. Turbulence is created in the setting chamber by means of eight 1/16-inch hypodermic tubes stretched normal to the flow and pressurized at any controlled value up to 6 psi. Each has twenty-one 0.006-inch holes spaced at 1-inch intervals along its mid-section of length, and directed upwind. The tubes are spaced vertically at 1.25-inch intervals. The turbulence so created is carried to the test section, where it is found to be spatially uniform over a suitably large cross-sectional area and axial length. Fig. 2 presents spectra of the steam turbulence in the empty tunnel for jet-array pressures of 1 psi to 6 psi. The T-S range extends between 80 and 150 Hz, approximately, for the present conditions. The primary method of fluctuation measurement is by use of microphones installed on the reverse side of the plate. A description of the method and its advantages has been given in AIAA 90-1504. Mean and fluctuating flow measurements are also made by means of various hot-wire probes and rakes carried on a computer-controlled x-y-z traverse mechanism. Fig. 3 shows the layout of a four-foot plate carrying 64 microphoned, the outputs of which are digitized simultaneously. The location of a single driver used for creating controlled T-S packets is also indicated.

Kendall, J. M.↗

NASA NTRS1986

Experiments on annular liquid jet instability and on the formation of liquid shells

An annular jet flow of liquid surrounding a flow of gas at its core is extremely unstable. Experiments are described in which such a flow is generated by an annular nozzle operated at fairly specific conditions. It is shown that periodic, axisymmetric oscillations arise spontaneously within the cylindrical sheet emerging from the nozzle and grow with such rapidity along the axial dimension that a sealing-off and encapsulation of the core gas occurs within a few jet diameters. This is closely followed by a pinchoff of the liquid between adjacent bubbles. The liquid shells set free thereby assume spherically symmetric form under capillary forces, and each contains a precisely uniform measure of gas and of liquid on account of the extremely high frequency-stability of the process. Description is given of the fluid dynamic processes by which the shells are formed, and mention is made of exploiting the instability for the production of rigid shells for technological applications.

Kendall, J. M.↗

NASA NTRS1985

Experimental study of disturbances produced in a pre-transitional laminar boundary layer by weak freestream turbulence

The high-amplitude, low-frequency, disturbances generated in a Blasius boundary layer by grid-produced freestream turbulence were studied by means of hot-wire anemometry and by flow visualization. Emphasis was placed on determining the cause and nature of these, and on their effect upon the mean flow profile. It was found that the motion in the layer was intrinsically three-dimensional, according to which the fronts, of Tollmien-Schlichting waves became warped. Evidence of streamwise vorticity was noted. At Reynolds numbers near 1.6 million, the maximum attained, sharp velocity gradients appeared locally. With increase of grid size, there appeared turbulent spots which were wider than the coherence scale of the background motion.

Kendall, J. M.↗

NASA NTRS1983

Free-stream noise and transition measurements on a cone in a Mach 3.5 pilot low-disturbance tunnel

A small scale Mach 3.5 wind tunnel incorporating certain novel design features and intended for boundary-layer-transition research has been tested. The free stream noise intensities and spectral distributions were determined throughout the test section for several values of unit Reynolds number and for nozzle boundary layer bleed on and off. The boundary layer transition location on a slender cone and the response of this to changes in the noise environment were determined. Root mean square free stream noise levels ranged from less than one tenth up to values approaching those for conventional nozzles, with the lowest values prevailing at upstream locations within the nozzle. For low noise conditions, cone transition Reynolds numbers were in the range of those for free flight; whereas for high noise conditions, they were in the range of those in conventional tunnels.

Beckwith, I. E.↗

NASA NTRS1983

Mass Producing Targets for Nuclear Fusion

Metal-encapsulating technique advances prospects of controlling nuclear fusion. Prefilled fusion targets form at nozzle as molten metal such as tin flows through outer channel and pressurized deuterium/tritium gas flows through inner channel. Molten metal completely encloses gas charge as it drops off nozzle.

Wang, T. G.↗

NASA NTRS1983

Free stream noise and transition measurements in a Mach 3.5 pilot quiet tunnel

Free stream fluctuating pressures are determined from hot-wire measurements in a Mach 3.5 pilot quiet nozzle over a unit Reynolds number range from 10-60 million per meter. Further, the transition Reynolds numbers on a sharp tip 5 degree half-angle cone at zero angle of attack are obtained over the same range of unit Reynolds numbers from equilibrium temperature measurements on the cone. Results show that the nozzle provides noise levels in the upstream regions of the test rhombus that are substantially lower than in conventional nozzles. The normalized rms levels of the fluctuating static pressures are found to vary from extremely low values of less than 0.03% up to about 0.8% depending on the unit Reynolds number, the axial location in the test rhombus, and the bleed slot flow. By opening the boundary-layer bleed flow, the wall boundary layers over upstream regions of the nozzle become laminar and the absence of high frequency radiated noise then results in cone transition Reynolds numbers that are in the range of free-flight data. As the unit Reynolds numbers are increased, the nozzle wall boundary layers become transitional and turbulent, and the noise increases to peak levels of about 0.5% with significant energy up to 150 KHz. The cone transition Reynolds numbers then decrease to values that are in the range of those measured in conventional wind tunnels.

Beckwith, I. E.↗

NASA NTRS1983

Surface characteristics of metallic glass spheres of Au(55)Pb(22.5)Sb(22.5)

It is pointed out that the production of metallic glasses of high atomic number is currently of considerable importance for inertial confinement fusion (ICF) target applications. In connection with the present investigation, spherules of the alloy Au(55)Pb(22.5)Sb(22.5) were produced. Metallic glass was formed on solidification. With the aid of X-ray diffraction studies, it was established that the spheres were completely amorphous. A near-surface phase separation on spheres of the metallic glass could be observed. Energy dispersive spectroscopy (EDS) measurements showed that the average composition of the surface differed from that of the bulk.

Lee, M. C.↗

NASA NTRS1982

Metal shell technology based upon hollow jet instability

Spherical shells of submillimeter size are sought as ICF targets. Such shells must be dimensionally precise, smooth, of high strength, and composed of a high atomic number material. A technology for the production of shells based upon the hydrodynamic instability of an annular jet of molten metal is described. Shells in the 0.7-2.0 mm size range have been produced using tin as a test material. Specimens exhibit good sphericity, fair concentricity, and excellent finish over most of the surface. Work involving a gold-lead-antimony alloy is in progress. Droplets of this are amorphous and possess superior surface finish. The flow of tin models that of the alloy well; experiments on both metals show that the technique holds considerable promise.

Kendall, J. M.↗

NASA NTRS1982

Hydrodynamic performance of an annular liquid jet: Production of spherical shells

An annular jet flow of liquid surrounding a flow of gas at its core is extremely unstable. Axisymmetric oscillations arise spontaneously, and grow with such rapidity along the axial dimension that a pinch-off of the liquid and an encapsulation of the core gas occurs within as few as four jet diameters. The shells which result thereby may be described as thick-wall bubbles, for which van der Waals forces are unimportant. A description is given of the fluid dynamic processes by which the shells are formed, and of means for preserving and promoting the geometrical of the product. The forming of metallic shells is mentioned.

Kendall, J. M.↗

NASA NTRS1982

Spheres of the metallic glass Au55 Pb22.5 Sb22.5 and their surface characteristics

Spheres of the metallic glass Au55 Pb22.5 Sb22.5 have been formed up to a size of approximately 1.5 mm in diameter. X-ray diffraction was used to establish the glassy nature of the samples and to provide evidence of two phase-separated glass regions. Scanning electron microscopy provided a direct visual observation of the two-phase amorphous network on the surface of the sphere. The physical dimensions of the phase-separated regions were observed to be cooling-rate sensitive. Energy dispersive spectroscopy indicated that the compositions of these two glassy phases were Au-rich and Pb-rich, respectively, confirming the results of Kim and Johnson (1981). In addition, the spheres exhibited an unusual surface smoothness of better than + or - 250 A

Lee, M. C.↗

NASA NTRS1982

Latest rocket measurements of the solar constant

Three rocket flights which carried a payload of absolute radiometers to measure the solar constant with an accuracy of plus or minus 0.5 per cent have been accomplished. Several of the rocket radiometers were duplicates of those aboard the Solar Maximum Mission and Nimbus spacecrafts. The values for the solar constant obtained by the rocket sensors for the three flight dates indicate an increase between the first and latter two flights approximately equivalent to the uncertainty of the measurements. The values for the solar constant for the three flights are 1367, 1372 and 1374 W/sq m.

Duncan, C. H.↗

NASA NTRS1982

Application of microgravity and containerless environments to the investigation of fusion target fabrication technology

After the first observation of the core-centering force within a liquid shell in the KC-135 flight experiment, this force was successfully reproduced in terrestrial laboratories using two experimental techniques. The core-centering force generated for a compound drop system in the neutral buoyancy tank provides the first correlation between theoretical and experimental results. When this force was generated in a more realistic fusion-pellet system using the focusing-radiator levitating system, it was shown that this is a very strong force indeed in view of the fact that the ratio of specific gravities between the water and the core is approximately five. It is believed that this centering force will contribute significantly to an overall understanding of the fabrication physics of a fusion target system. Results from experiments in a vertical drag-free wind tunnel and in a 16-ft low pressure drop furnace suggest that eliminating or reducing the aerodynamic drag on fusion pellets during their formation stage will prevent the decentering of the bubble. Metallic and metallic glass fusion targets are seen as holding promise for improving and simplifying the fabrication process for ablative-type fusion targets.

Lee, M. C.↗

NASA NTRS1982

Investigation of metallic and metallic glass hollow spheres for fusion target application

The first successful formation of submillimeter and millimeter spherical shells of tin and of a gold-lead-antimony alloy by means of the hollow-jet instability technique developed by Kendall is reported. Examination of tin specimens by SEM reveals that surface quality varies from poor to excellent. Whereas the metal is employed only as a convenient and inexpensive material, the gold alloy is important in that it is hard, has a high atomic number, and may be solidified into the amorphous state through the provision of a modest cooling rate. AuPbSb spherules up to 1.5 mm in diameter are produced using LN2 or chilled methanol as a coolant. It is found that these amorphous samples possess a superb surface smoothness compatible with fusion target requirements. It is noted that hollow spheres currently made of this alloy have an average outside diameter of 2000 microns.

Lee, M. C.↗

NASA NTRS1980

Noise generation by a lifting wing/flap combination at Reynolds numbers to 2.8 x 10 to the 6th

Measurements relating to the noise source location and intensity within various frequency bands were made for an 0.75 m-chord wing/flap model installed in the Ames 7 x 10-foot wind tunnel. A directional microphone system, located outside the open-wall tunnel was scanned in a two-dimensional array of aiming points about the positive-pressure side of the model to determine the principal locations of noise production, and the intensity of each of these. It was found for the case of the flaps being differentially deflected (0 deg, 35 deg) at the half-span station that noise production was concentrated in the immediate region of the resultant surface discontinuity. For equal deflection of the halves (0 deg, 0 deg or 35 deg, 35 deg), noise was produced uniformly along the length of the gap between the wing and the flap. Simulated flap-mounting brackets generated considerable noise in certain cases, but reduced the noise in others. Trailing edge noise did not appear to be important in comparison with other sources.

Kendall, J. M.↗

NASA NTRS1979

Resolution enhanced sound detecting apparatus

An apparatus is described for enhancing the resolution of a sound detector of the type which includes an acoustic mirror for focusing sound from an object onto a microphone to enable the determination of the location from which the sound arises. The enhancement apparatus includes an enclosure which surrounds the space between the mirror and microphone, and contains a gas heavier than air, such as Freon, through which sound moves slower and therefore with a shorter wavelength than in air, so that a mirror of given size has greater resolving power. An acoustically transparent front wall of the enclosure which lies forward of the mirror, can include a pair of thin sheets with pressured air between them, to form an end of the region of heavy gas into a concave shape.

Kendall, J. M.↗

NASA NTRS1979

Free oscillations of a large drop in space

In preparation for forthcoming studies on materials processing in space, techniques and equipment are being developed for the deployment and control of large globules of liquid in a zero-g environment. This paper first presents a theoretical analysis of the intense sound field within an enclosure by which positioning forces, torques, and temporal perturbations may be applied to a sample. Procedures for digital analysis of photographic records of the sample motion are described. Results on the mean and oscillatory motion of a 2.5 cm diameter water drop during the flight of a SPAR rocket are given. In particular, spectral analysis shows that the drop oscillates at several frequencies. Identification with theoretically expected modes is made for some of the spectral lines.

Jacobi, N.↗

NASA NTRS1978

Measurements of noise produced by flow past lifting surfaces

Wind tunnel studies have been conducted to determine the specific locations of aerodynamic noise production within the flow field about various lifting-surface configurations. The models tested included low aspect ratio shapes intended to represent aircraft flaps, a finite aspect ratio NACA 0012 wing, and a multi-element wing section consisting of a main section, a leading edge flap, and dual trailing edge flaps. Turbulence was induced on the models by surface roughness. Lift and drag were measured for the flap models. Hot-wire anemometry was used for study of the flap-model vortex roll-up. Apparent noise source distributions were measured by use of a directional microphone system, located outside the tunnel, which was scanned about the flow region to be analyzed under computer control. These distributions exhibited a diversity of pattern, suggesting that several flow processes are important to lifting-surface noise production. Speculation concerning these processes is offered.

Kendall, J. M.↗

NASA NTRS1977

Airframe noise measurements by acoustic imaging

Studies of the noise produced by flow past wind tunnel models are presented. The central objective of these is to find the specific locations within a flow which are noisy, and to identify the fluid dynamic processes responsible, with the expectation that noise reduction principles will be discovered. The models tested are mostly simple shapes which result in types of flow that are similar to those occurring on, for example, aircraft landing gear and wheel cavities. A model landing gear and a flap were also tested. Turbulence has been intentionally induced as appropriate in order to simulate full-scale effects more closely. The principal technique involves use of a highly directional microphone system which is scanned about the flow field to be analyzed. The data so acquired are presented as a pictorial image of the noise source distribution. An important finding is that the noise production is highly variable within a flow field and that sources can be attributed to various fluid dynamic features of the flow. Flow separation was not noisy, but separation closure usually was.

Kendall, J. M.↗