Engineering Papers⌕ Search

Engineering topics

Keiser, Dennis

Publications and source records attributed to Keiser, Dennis.

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Atom probe tomography of segregation at grain boundaries and gas bubbles in neutron irradiated U-10 wt% Mo fuel

During neutron irradiation to fission densities > 5.2 × 10 21 fiss/cm 3 , Xe agglomerates forming gas bubbles of varying size within the U-Mo fuel matrix. Herein, segregation of fission products to Xe bubbles and grain boundaries (GB) were studied using atom probe tomography (APT). Segregation behavior was found to vary among GBs, small bubbles (<10 nm), and larger bubbles (>10 nm). Solid fission products were enriched at GBs and larger bubbles, but not at small bubbles. Finally, a denuded zone was identified adjacent to a > 10 nm Xe gas bubble and a GB.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The role of UC inclusions in the development of fission gas bubble superlattice neutron-irradiated monolithic U-10Mo fuels

Uranium Carbide (UC) inclusions are the most prevalent impurities in Uranium-Molybdenum (U-Mo) fuel and are considered undesirable because they could potentially affect fuel performance. This work revealed that, like grain boundaries (gBs), UC inclusions could help facilitate the formation of the fission gas bubble superlattice (GBS). The GBS is a highly organized complex defect structure that can effectively store fission gases, thereby inhibiting fuel swelling. Transmission electron microscopy (TEM) showed that GBS self-organization can initiate at the UC/U-Mo interfaces in U-10Mo fuel irradiated to low fission density. Furthermore, this study also revealed that the UC boundary in U-10Mo irradiated to low fission density is wavy and periodic in morphology and that GBS formation is semi-coherent with the UC boundary. Because the initiation of GBS occurs at gBs and UC/U-Mo interfaces, the fission gas inventory is always highest at those regions compared to the U-Mo grain interior. Consequently, at higher fission densities, it is likely that high burnup structure (HBS) development via grain refinement will begin at gBs and UC/U-Mo interfaces.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Possible impacts of Mo chemical banding and second phase impurities on the irradiation behavior of monolithic U-10Mo fuels

This study investigated the microstructural behavior of both full-size and mini-size monolithic U-10Mo fuel plates irradiated to high burnup with a focus on the evolution of the second phase impurities in monolithic U-Mo using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and wavelength dispersive spectroscopy (WDS). Key indicators of possible mechanical and thermal compromise include cracks, large fission gas porosity, and interconnection of fission gas pores. For the fission densities evaluated in this work (3.5 × 10 21 fissions/cm 3 -5.1 × 10 21 fissions/cm 3 ), fine porosity can develop along the UC phase boundary; however, the size of the fission gas pores is no more than those observed in the U-Mo fuel phase. Further, other inclusions such as Si-rich second-phase impurities found in the as-fabricated microstructure were difficult to resolve post-irradiation because they can become overshadowed by porosity development in the fuel phase. Additionally, the presence of a Fe-rich sublayer formed in the Zr diffusion layer during fabrication remained enriched in the Zr layer in the irradiated U-10Mo microstructures near the U-Mo/Zr interface; however, based on the burnup assessed in this study the identified impurities did not appear to contribute to notable microstructural degradation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Acceptance Test of WCTC with LEU Fuel at the IVG.1M Research Reactor Site in Kazakhstan

The water-cooled technological channels (WCTC) with low-enriched uranium (LEU) fuel, in the amount required for conversion, were delivered to the IVG.1M site by the manufacturer in February 2021 and thereafter the site acceptance test (SAT) of the WCTCs and the fuel elements started immediately. The paper provides an overview of the SAT conducted between March and November 2021 by the designated experts of the reactor operator and the manufacturer. It includes the introduction of the IVG.1M reactor and its unique WCTCs, and the inspection methodology to verify the conformity of the quality of the LEU fuel with the Technical Design (reference document). The paper presents results of the non-destructive and destructive tests, the outcomes of the thermohydraulic measurements, as well as the evaluation and corrective actions (if any), including the amendments (modifications) of the Technical Design initiated by the manufacturer based on the test results. Finally, the paper draws conclusions on the effectiveness of the SAT method used, captures consolidated experiential knowledge and shares lessons learned that can be used in general when planning and performing fuel verification.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Microstructural Changes and Chemical Analysis of Fission Products in Irradiated Uranium-7 wt.% Molybdenum Metallic Fuel Using Atom Probe Tomography

Understanding the microstructural and phase changes occurring during irradiation and their impact on metallic fuel behavior is integral to research and development of nuclear fuel programs. This paper reports systematic analysis of as-fabricated and irradiated low-enriched U-Mo (uranium-molybdenum metal alloy) fuel using atom probe tomography (APT). This study is carried out on U-7 wt.% Mo fuel particles coated with a ZrN layer contained within an Al matrix during irradiation. The dispersion fuel plates from which the fuel samples were extracted are irradiated at Belgian Nuclear Research Centre (SCK CEN) with burn-up of 52% and 66% in the framework of the SELENIUM (Surface Engineering of Low ENrIched Uranium-Molybdenum) project. The APT studies on U-Mo particles from as-fabricated fuel plates enriched to 19.8% revealed predominantly γ-phase U-Mo, along with a network of the cell boundary decorated with α-U, γ’-U2Mo, and UC precipitates along the grain boundaries. The corresponding APT characterization of irradiated fuel samples showed formation of fission gas bubbles enriched with solid fission products. The intermediate burnup sample showed a uniform distribution of the typical bubble superlattice with a radius of 2 nm arranged in a regular lattice, while the high burnup sample showed a non-uniform distribution of bubbles in grain-refined regions. There was no evidence of remnant α-U, γ’-U2Mo, and UC phases in the irradiated U-7 wt.% Mo samples.

Bachhav, Mukesh↗
DOE OSTI2017

Mechanical properties examined by nanoindentation for selected phases relevant to the development of monolithic uranium-molybdenum metallic fuels

Nanomechanical properties, specifically the reduced modulus and hardness of several intermetallic and solid solution phases are reported here to assist the development of the U-10 wt% Mo (U-10Mo) monolithic fuel system for research and test reactors. Findings from this study and reported values of mechanical properties provide data critical for understanding and predicting the structural behavior of the fuel system during fabrication and irradiation. The phases examined are products of interdiffusion and reaction between (1) the AA6061 cladding and the Zr diffusion barrier, namely (Al,Si) 3 Zr and Al 3 Zr, (2) the U-10Mo fuel and the Zr diffusion barrier, namely UZr 2 , Mo 2 Zr, and a-U, and (3) the U (or U-10Mo) and Mo, namely a mixture gradient of α- and γ-phases. The UC inclusions observed within the fuel alloy were also examined. Only phases present in thick or continuous microstructure on cross-sectioned fuel plates and diffusion couples were investigated for reduced modulus and hardness. Concentration-dependence of room-temperature reduced modulus in U solid solution with 0–10 wt% Mo was semi-quantitatively modeled based on mixture of α- and γ-phases and solid solutioning within the γ-phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2014

TEM Characterization of High Burn-up Microstructure of U-7Mo Alloy

As an essential part of global nuclear non-proliferation effort, the RERTR program is developing low enriched U-Mo fuels (< 20% U-235) for use in research and test reactors that currently employ highly enriched uranium fuels. One type of fuel being developed is a dispersion fuel plate comprised of U-7Mo particles dispersed in Al alloy matrix. Recent TEM characterizations of the ATR irradiated U-7Mo dispersion fuel plates include the samples with a local fission densities of 4.5, 5.2, 5.6 and 6.3 E+21 fissions/cm3 and irradiation temperatures of 101-136?C. The development of the irradiated microstructure of the U-7Mo fuel particles consists of fission gas bubble superlattice, large gas bubbles, solid fission product precipitates and their association to the large gas bubbles, grain subdivision to tens or hundreds of nanometer size, collapse of bubble superlattice, and amorphisation. This presentation will describe the observed microstructures specifically focusing on the U-7Mo fuel particles. The impact of the observed microstructure on the fuel performance and the comparison of the relevant features with that of the high burn-up UO2 fuels will be discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2014

Stability Study of the RERTR Fuel Microstructure

The irradiation stability of the interaction phases at the interface of fuel and Al alloy matrix as well as the stability of the fission gas bubble superlattice is believed to be very important to the U-Mo fuel performance. In this paper the recent result from TEM characterization of Kr ion irradiated U-10Mo-5Zr alloy will be discussed. The focus will be on the phase stability of Mo2-Zr, a dominated second phase developed at the interface of U-10Mo and the Zr barrier in a monolithic fuel plate from fuel fabrication. The Kr ion irradiations were conducted at a temperature of 200 degrees C to an ion fluence of 2.0E+16 ions/cm2. To investigate the thermal stability of the fission gas bubble superlattice, a key microstructural feature in both irradiated dispersion U-7Mo fuel and monolithic U-10Mo fuel, a FIB-TEM sample of the irradiated U-10Mo fuel (3.53E+21 fission/cm3) was used for a TEM in-situ heating experiment. The preliminary result showed extraordinary thermal stability of the fission gas bubble superlattice. The implication of the TEM observation from these two experiments on the fuel microstructural evolution under irradiation will be discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗