Engineering topics

Kashiwagi, Takashi

Publications and source records attributed to Kashiwagi, Takashi.

16 records

NASA NTRS2004

Transition from Ignition to Flame Growth under External Radiation in 3D

This study focuses on localized ignition by external radiant flux and subsequent flame growth over thin polymeric materials (plastic and paper) in microgravity. Two transition stages were observed. The first transition stage covers the period from the onset of ignition to the formation of stabilized flame near the ignited area. This is followed by the second transition of the flame growth stage from the initial stabilized flame to sustained fire growth away from the ignited area. For the first stage, ignition experiments of thin PMMA sheets were conducted using a CO2 laser as an external source in the 10 s drop tower. The results of front side surface ignition and of backside surface ignition were observed. The effects of imposed flow velocity, sample thickness, and ambient oxygen concentration on ignition are obtained. Numerical study was conducted to investigate to understand and predict ignition behavior observed in the experiments. For the second stage, numerical study is being conducted to describe the effects of gravity on heat release rate of a PMMA sheet. The gravity level was varied from zero to normal gravity. The preliminary results show that the maximum heat release occurs at around 0.02 g.

Kashiwagi, Takashi↗

NASA NTRS2004

Transition from Ignition to Flame Growth under External Radiation in Three Dimensions (TIGER-3D)

Kashiwagi, Takashi↗

NASA NTRS2003

Effect Of Low External Flow On Flame Spreading Over ETFE Insulated Wire Under Microgravity

Fire safety is one of the most important issues for manned space missions. A likely cause of fires in spacecraft is wire insulation combustion in electrical system. Regarding the wire insulation combustion it important to know the effect of low external flow on the combustion because of the presence of ventilation flow in spacecraft. Although, there are many researches on flame spreading over solid material at low external flows under microgravity, research dealing with wire insulation is very limited. An example of wire insulation combustion in microgravity is the Space Shuttle experiments carried out by Greenberg et al. However, the number of experiments was very limited. Therefore, the effect of low flow velocity is still not clear. The authors have reported results on flame spreading over ETFE (ethylene - tetrafluoroetylene) insulated wire in a quiescent atmosphere in microgravity by 10 seconds drop tower. The authors also performed experiments of polyethylene insulated nichrom wire combustion in low flow velocity under microgravity. The results suggested that flame spread rate had maximum value in low flow velocity condition. Another interesting issue is the effect of dilution gas, especially CO2, which is used for fire extinguisher in ISS. There are some researches working on dilution gas effect on flame spreading over solid material in quiescent atmosphere in microgravity. However the research with low external flow is limited and, of course, the research discussing a relation of the appearance of maximum wire flammability in low flow velocity region with different dilution gas cannot be found yet. The present paper, therefore, investigates the effect of opposed flow with different dilution gas on flame spreading over ETFE insulated wire and change in the presence of the maximum flammability depending on the dilution gas type is discussed within the limit of microgravity time given by ground-based facility.

Nishizawa, Katsuhiro↗

NASA NTRS2002

Effect of Wind Velocity on Flame Spread in Microgravity

A three-dimensional, time-dependent model is developed describing ignition and subsequent transition to flame spread over a thermally thin cellulosic sheet heated by external radiation in a microgravity environment. A low Mach number approximation to the Navier Stokes equations with global reaction rate equations describing combustion in the gas phase and the condensed phase is numerically solved. The effects of a slow external wind (1-20 cm/s) on flame transition are studied in an atmosphere of 35% oxygen concentration. The ignition is initiated at the center part of the sample by generating a line-shape flame along the width of the sample. The calculated results are compared with data obtained in the 10s drop tower. Numerical results exhibit flame quenching at a wind speed of 1.0 cm/s, two localized flames propagating upstream along the sample edges at 1.5 cm/s, a single line-shape flame front at 5.0 cm/s, three flames structure observed at 10.0 cm/s (consisting of a single line-shape flame propagating upstream and two localized flames propagating downstream along sample edges) and followed by two line-shape flames (one propagating upstream and another propagating downstream) at 20.0 cm/s. These observations qualitatively compare with experimental data. Three-dimensional visualization of the observed flame complex, fuel concentration contours, oxygen and reaction rate isosurfaces, convective and diffusive mass flux are used to obtain a detailed understanding of the controlling mechanism, Physical arguments based on lateral diffusive flux of oxygen, fuel depletion, oxygen shadow of the flame and heat release rate are constructed to explain the various observed flame shapes.

Prasad, Kuldeep↗

NASA NTRS2001

TIGER Burned Brightly in JAMIC

The Transition From Ignition to Flame Growth Under External Radiation in 3D (TIGER- 3D) experiment, which is slated to fly aboard the International Space Station, conducted a series of highly successful tests in collaboration with the University of Hokkaido using Japan's 10-sec JAMIC drop tower. The tests were conducted to test engineering versions of advanced flight diagnostics such as an infrared camera for detailed surface temperature measurements and an infrared spectroscopic array for gas-phase species concentrations and temperatures based on detailed spectral emissions in the near infrared. Shown in the top figure is a visible light image and in the bottom figure is an infrared image at 3.8 mm obtained during the microgravity tests. The images show flames burning across cellulose samples against a slow wind of a few centimeters per second (wind is from right to left). These flow velocities are typical of spacecraft ventilation systems that provide fresh air for the astronauts. The samples are ignited across the center with a hot wire, and the flame is allowed to spread upwind and/or downwind. As these images show, the flames prefer to spread upwind, into the fresh air, which is the exact opposite of flames on Earth, which spread much faster downwind, or with the airflow, as in forest fires.

Olson, Sandra L.↗

NASA NTRS1999

Ignition, Transition, Flame Spread in Multidimensional Configurations in Microgravity

In the inhabited quarters of orbiting spacecraft, fire is a greatly feared hazard. Thus, the fire safety strategy in a spacecraft is (1) to keep any fire as small as possible, (2) to detect any fire as early as possible, and (3) to extinguish any fire as quickly as possible. This suggests that a material which undergoes a momentary ignition might be tolerable but a material which permits a transition from a localized ignition to flame spread would significantly increase the fire hazard in a spacecraft. If the transition does not take place, fire growth does not occur. Therefore, it is critical to understand what process controls the transition. Many previous works have studied ignition and flame spread separately or were limited to a two-dimensional configuration. In this study, time-dependent phenomena of the transition over a thermally thin sample is studied experimentally and theoretically in two- and three-dimensional (2D,3D) configurations. Furthermore, localized ignition can be initiated at the center portion of thermally thin paper sample instead of at one end of the sample. Thus, the transition to flame spread could occur either toward upstream or downstream or both directions simultaneously with an external flow. In this presentation, the difference in the transition between the 3D and 2D configurations is explained with the numerically calculated data. For sufficiently narrow samples edge effects exist. Some results on this issue are presented. New analysis of the surface smoldering experiments conducted in the space shuttle STS-75 flight is also described.

Kashiwagi, Takashi↗

NASA NTRS1998

Radiative Ignition and Transition to Spread Investigation (RITSI)

A total of 25 experiments was conducted in the Glovebox Facility on the Third United States Microgravity payload (USMP3) mission to study the behavior of both flaming and smoldering ignition events, the transition from ignition to the flame/smoldering spread, and the flame/smoldering growth pattern in air. Twenty one of the 25 experiments were flaming experiments and the remainder were smoldering experiments. Ignition was initiated by a heated wire across a thermally thin filter paper in the middle of the sample for the two-dimensional configuration and by a focused beam from a halogen/tungsten lamp at the center of the sample for the three-dimensional configuration. The external air flow velocity was varied from 0 cm/s to 6.5 cm/s. The ignition and subsequent flame spread events were recorded by a video camera, a 35 mm camera, and 6 thermocouples (2 in the gas phase and 4 in the sample). The results indicate that non-piloted radiative ignition of the paper by external thermal radiation tends to occur more easily than in normal gravity. In the two-dimensional configuration, the transition from ignition to downstream flame spread never occurred; only the transition to upstream spread took place. In the three-dimensional configuration, a char growth pattern emerged in the shape of a fan, with the ignited area as the center of the fan and the fan spreading in the upstream direction. The internal angle of the fan increased with an increase in external flow velocity (higher flow velocity gave a more opened fan pattern). At an external flow velocity of 5 cm/s, the flame was horseshoe-shaped and the char pattern became an elongated semicircle toward upstream. It appears that the peak upstream flame spread rate was reached at a higher external velocity than for the two-dimensional flame front. Flame spread much faster along open edges of the sample paper than along the sample face, presumably due to there being larger supply of oxygen and energy feedback at the open edges than at the surface. These results indicate the possible importance of the effect of the flame front shape such as the curvature of the flame front on spread rate and flame strength. A complex, unexpected finger-shaped char growth pattern was observed during the smoldering experiment. Higher external flow velocity increased the number of localized smoldering fronts, of the char fingers they left behind, and frequency of bifurcations from the fingers. At present, it is not clear what caused such a complex char growth pattern.

Kashiwagi, Takashi↗

NASA NTRS1997

Ignition, Transition, Flame Spread in Multidimensional Configurations in Microgravity

Ignition of solid fuels by external thermal radiation and subsequent transition to flame spread are processes that not only are of considerable scientific interest but which also have fire safety applications. A material which undergoes a momentary ignition might be tolerable but a material which permits a transition to subsequent flame spread would significantly increase the fire hazard in a spacecraft. Therefore, the limiting condition under which flame cannot spread should be calculated from a model of the transition from ignition instead of by the traditional approach based on limits to a steady flame spread model. However, although the fundamental processes involved in ignition have been suggested there have been no definitive experimental or modeling studies due to the flow motion generated by buoyancy near the heated sample surface. In this study, microgravity experiments which required longer test times such as in air and surface smoldering experiment were conducted in the space shuttle STS-75 flight; shorter experimental tests such as in 35% and 50% oxygen were conducted in the droptower in the Japan Microgravity Center, JAMIC. Their experimental data along with theoretically calculated results from solving numerically the time-dependent Navier-Stokes equations are summarized in this paper.

Kashiwagi, Takashi↗

NASA NTRS1995

The USML-1 wire insulation flammability glovebox experiment

Flame spreading tests have been conducted using thin fuels in microgravity where buoyant convection is suppressed. In spacecraft experiments flames were ignited in quiescent atmospheres with an elevated oxygen content, demonstrating that diffusional mechanisms can be sufficient alone to sustain flame spreading. In ground-based facilities (i.e. drop towers and parabolic aircraft) low-speed convection sustains flames at much lower concentrations of atmospheric oxygen than in quiescent microgravity. Ground-based experiments are limited to very thin fuels (e.g., tissue paper); practical fuels, which are thicker, require more test time than is available. The Glovebox Facility provided for the USML 1 mission provided an opportunity to obtain flame spreading data for thicker fuel Herein we report the results from the Wire Insulation Flammability (WIF) Experiment performed in the Glovebox Facility. This experiment explored the heating, ignition and burning of 0.65 mm thick polyethylene wire insulation in low-speed flows in a reduced gravity environment. Four tests were conducted, two each in concurrent flow (WIF A and C) and opposed flow (WIF B and D), providing the first demonstration of flame spreading in controlled forced convection conducted in space.

Greenberg, Paul S.↗

NASA NTRS1995

Ignition and subsequent transition to flame spread in a microgravity environment

The fire safety strategy in a spacecraft is (1) to detect any fire as early as possible, (2) to keep any fire as small as possible, and (3) to extinguish any fire as quickly as possible. This suggests that a material which undergoes a momentary, localized ignition might be tolerable but a material which permits a transition to flame spread would significantly increase the fire hazard. Therefore, it is important to understand how the transition from localized ignition to flame spread occurs and what parameters significantly affect the transition. The fundamental processes involved in ignition and flame spread have been extensively studied, but they have been studied separately. Some of the steady state flame models start from ignition to reach a steady state, but since the objective of such a calculation is to obtain the steady state flame spread rate, the calculation through the transition process is made without high accuracy to save computational time. We have studied the transition from a small localized ignition at the center of a thermally thin paper in a microgravity environment. The configuration for that study was axisymmetric, but more general versions of the numerical scheme have been developed by including the effects of a slow, external flow in both two and three dimensions. By exploiting the non-buoyant nature of the flow, it is possible to achieve resolution of fractions of millimeters for 3D flow domains on the order of 10 centimeters. Because the calculations are time dependent, we can study the evolution of multiple flame fronts originating from a localized ignition source. The interaction of these fronts determines whether or not they will eventually achieve steady state spread. Most flame spread studies in microgravity consider two-dimensional flame spread initiated by ignition at one end of a sample strip with or against a slow external flow. In this configuration there is only one flame front. A more realistic scenario involves separate, oppositely directed fronts in two dimensions, or a continuous, radially directed front in three dimensions. We present here some results of both the two and three dimensional codes.

Kashiwagi, Takashi↗

NASA NTRS1994

Wire Insulation Flammability Experiment: USML-1 One Year Post Mission Summary

Herein we report the results from the Wire Insulation Flammability (WIF) Experiment performed in the Glovebox Facility on the USML-1 mission. This experiment explored various aspects of electrically induced fire scenarios in a reduced gravity environment. Under quiescent microgravity conditions, heat and mass transfer are dominated by diffusive and radiative transport; while in normal-gravity buoyancy induced convection often dominates. Of considerable scientific and practical interest is the intermediate situation of combustion occurring in the presence of imposed gas flows, with lower characteristic velocities than those induced by buoyancy in noma1 gravity. Two distinct cases naturally arise: flow direction opposed to, or concurrent with, the flame spread direction. Two tests of each kind were conducted in the WIF experiment, providing the first controlled demonstration of flame spreading in forced convection ever conducted in space. Four test modules were flown. The wire insulation, 1.5 mm in diameter, was polyethylene, extruded onto nichrome wire. Temperatures of the wh3 cores and insulation heated in quiescent and flowing environments were measured. Video and still-camera images of the samples, burning in air flowing at approximately 10 cm/sec, were recorded to obtain flame characteristics including spread rate, structure and temperature. Flame spread rates in concurrent flow were approximately twice those in opposed flow. In concurrent and opposed flow regimes, the spreading flames stabilized around a bead of molten insulation material, within which bubble nucleation was observed. An ignition attempt without flow mated a quiescent cloud of vaporized fuel which ignited dramatically yet failed to sustain normal flame spread. Finally, all tests produced substantial soot agglomerates, particularly the concurrent flow tests; and the collected soot has a morphology very distinct from soot formed in normal gravity flames. Several unexpected and unique microgravity combustion phenomena were observed.

Greenberg, Paul S.↗

NASA NTRS1994

Ignition and Wind Effects on the Transition to Flame Spread in a Microgravity Environment

The fundamental processes involved in ignition and flame spread have been extensively studied, they are generally studied separately without combining ignition and flame spread through the transition process. Moreover, the majority of the flame spread studies assume steady state flame spread. To study the transient aspects of ignition and the transition to flame spread, a time-dependent numerical model has been developed in which a thin strip is ignited along its width with either a pilot wire, radiative source, or both. For this configuration, the model is two-dimensional. Ignition is initiated away from either end of the sample, and two different flame fronts spread in opposite directions; one flows with and the other against a prescribed external flow. Usually, the flame spread is initiated by ignition at one end of the sample with or against a slow external flow, yielding one flame front. The present configuration is more realistic than the one flame front case because there is interaction between the two flames during the ignition and transition stages.

McGrattan, Kevin B.↗

NASA NTRS1993

Ignition and subsequent flame spread over a thin cellulosic material

Both ignition and flame spread on solid fuels are processes that not only are of considerable scientific interest but that also have important fire safety applications. Both types of processes, ignition and flame spread, are complicated by strong coupling between chemical reactions and transport processes, not only in the gas phase but also in the condensed phase. In most previous studies, ignition and flame spread were studied separately with the result that there has been little understanding of the transition from ignition to flame spread. In fire safety applications this transition is crucial to determine whether a fire will be limited to a localized, temporary burn or will transition into a growth mode with a potential to become a large fire. In order to understand this transition, the transient mechanisms of ignition and subsequent flame spread must be studied. However, there have been no definitive experimental or modeling studies, because of the complexity of the flow motion generated by buoyancy near the heated sample surface. One must solve the full Navier-Stokes equations over an extended region to represent accurately the highly unstable buoyant plume and entrainment of surrounding gas from far away. In order to avoid the complicated nature of the starting plume problem under normal gravity, previous detailed radiative ignition models were assumed to be one-dimensional or were applied at a stagnation point. Thus, these models cannot be extended to include the transition to flame spread. The mismatch between experimental and calculated geometries means that theories cannot be compared directly with experimental results in normal gravity. To overcome the above difficulty, theoretical results obtained without buoyancy can be directly compared with experimental data measured in a microgravity environment. Thus, the objective of this study is to develop a theoretical model for ignition and the transition to flame spread and to make predictions using the thermal and chemical characteristics of a cellulosic material which are measured in normal gravity.

Nakabe, Kazuyoshi↗

NASA NTRS1992

Global Kinetic Constants for Thermal Oxidative Degradation of a Cellulosic Paper

Values of global kinetic constants for pyrolysis, thermal oxidative degradation, and char oxidation of a cellulosic paper were determined by a derivative thermal gravimetric study. The study was conducted at heating rates of 0.5, 1, 1.5, 3, and 5 C/min in ambient atmospheres of nitrogen, 0.28, 1.08, 5.2 percent oxygen concentrations, and air. Sample weight loss rate, concentrations of CO, CO2, and H2O in the degradation products, and oxygen consumption were continuously measured during the experiment. Values of activation energy, preexponential factor, orders of reaction, and yields of CO, CO2, H2O, total hydrocarbons, and char for each degradation reaction were derived from the results. Heat of reaction for each reaction was determined by differential scanning calorimetry. A comparison of the calculated CO, CO2, H2O, total hydrocarbons, sample weight loss rate, and oxygen consumption was made with the measured results using the derived kinetic constants, and the accuracy of the values of kinetic constants was discussed.

Kashiwagi, Takashi↗

NASA NTRS1989

Expert systems applied to spacecraft fire safety

Expert systems are problem-solving programs that combine a knowledge base and a reasoning mechanism to simulate a human expert. The development of an expert system to manage fire safety in spacecraft, in particular the NASA Space Station Freedom, is difficult but clearly advantageous in the long-term. Some needs in low-gravity flammability characteristics, ventilating-flow effects, fire detection, fire extinguishment, and decision models, all necessary to establish the knowledge base for an expert system, are discussed.

Smith, Richard L.↗

NASA NTRS1987

Temperature and concentration measurements in combustion

A high speed two wavelength holographic interferometer is being used to simultaneously measure temperature and concentration distributions for ignition and flame spread. Lines from a cw CO2 laser were used and the holograms recorded on a movie at 500 frames per/sec, individual frames were digitized with a microdensitometer. The detection on the fringe center was a major problem.

Kashiwagi, Takashi↗