Engineering topics

Kasa, Matthew

Publications and source records attributed to Kasa, Matthew.

11 records

DOE OSTI2022

Design, Construction, and Testing of 0.5-m, 18-mm Period Nb 3 Sn Superconducting Undulator Magnets

We report design and fabrication of a new Nb 3 Sn-based superconducting undulator (SCU) are underway at the Advanced Photon Source (APS) of Argonne National Laboratory in collaboration with Fermilab and Lawrence Berkeley National Laboratory. To develop a robust and reliable fabrication process, the magnet development consists of several steps. First, magnetic and mechanical simulations were performed to optimize the magnet design; then, the design matured further by fabricating and testing a series of very short prototypes, ~8 cm long with a period length of 18 mm. These short prototype studies were previously reported. Second, the design was scaled to an intermediate length of ~0.5 m. These two steps led to the final design of ~1.1–m-long magnets, which are currently being fabricated. The quench behavior of each 0.5-m-long undulator magnet, as well as undulator assemblies from these magnets, was studied. The first SCU magnet assembly did not meet the design specifications due to the breakdown of the insulation. With an improved design and fabrication process based on lessons learned, the second SCU assembly achieved the design undulator field of 1.2 T. The design was further optimized, and the third set of magnets was fabricated and successfully tested.

43 PARTICLE ACCELERATORS↗

DOE OSTI2021

Vertical Septum Magnet Design for the APS Upgrade

The vertical injection scheme proposed for the APS Upgrade (APS-U) Project requires a challenging septum magnet that must meet stringent beam physics, magnetic field leakage, and vacuum requirements. The current iteration of this magnet design includes an enlarged stored-beam chamber aperture of 9 mm x 12 mm and a reduction of the septum thickness to 1.5 mm. The enlarged aperture accommodates a non-evaporable getter (NEG)-coated stored beam chamber to better achieve the required vacuum. A prototype septum magnet has been built and measurements confirm the cancellation of a peak leakage field even though the value is six times larger than the design. The leakage field measured at the upstream (US) end cancels the downstream (DS) end as was expected by design. The measured and simulated leakage field and the stored beam trajectories are reported.

43 PARTICLE ACCELERATORS↗

DOE OSTI2021

Helical superconducting undulator for 3rd and 4th generation of synchrotron light source and FELs

A helical superconducting undulator includes a cylindrical magnetic core through which a bore hole allows the passage of charged particles. A single superconducting wire wraps the magnetic core guided by helical flights and cylindrical protrusions, to create interleaved helical windings on the magnetic core. An electrical current may be supplied to the superconducting wire to generate a periodic helical magnetic field in the bore. The helical superconducting undulator also includes a strong-back enclosure that acts as an epoxy mold during epoxy impregnation, a structural support to ensure straightness of the undulator after epoxy impregnation, and assists in cooling and thermal control of the magnetic core and superconducting wire during device operation.

Gluskin, Efim↗

DOE OSTI2021

Fabrication and Testing of 18-mm-Period, 0.5-m-Long Nb 3 Sn Superconducting Undulator

The Advanced Photon Source at Argonne National Laboratory, in collaboration with FNAL and LBNL, is developing a Nb 3 Sn superconducting undulator with the goal of installing this device on the APS storage ring and providing APS users with the novel radiation source. A series of short, similar to ~ 8-cm-long, 18-mm-period undulator prototype magnets have been designed, fabricated, and tested. The same design was scaled to fabricate a 0.5-m-long undulator prototype. Tests of this prototype showed that the designed peak magnetic field of 1.2 T at 850 A was successfully achieved. It represents at least a 20% improvement in comparison with a NbTi SCU having the same period and magnetic gap. Test results and lessons learned from the design process are reported here.

43 PARTICLE ACCELERATORS↗

DOE OSTI2020

Heat Treatment Studies of Nb3Sn Wires for Superconducting Planar Undulators

A project aiming to fabricate a full-length 2.8-m long Nb 3Sn superconducting undulator for the storage ring was started last year at the ANL APS. These Nb 3 Sn undulators operate at a maximum magnetic field on the conductor of about 5 T. To address instabilities at this field, two Nb 3 Sn wires with small subelement size were used. Specifically, Restacked Rod Processed wires of 0.6mmin diameter and with 144 and 150 superconducting subelements respectively, over 169 total. The equivalent subelement diameter, DS, of thesewires is35 mu m. At these smallDS values, the critical current density is known to deteriorate, and the Residual Resistivity Ratio is very sensitive to heat treatment. A delicate balance has therefore to be found to obtain parameters within operation specifications. In this paper we showperformance results from different heat treatments.

critical current density↗

DOE OSTI2019

Continuous winding magnets using thin film conductors without resistive joints

A continuous winding method produces a continuously wound electrical device, such an undulator. A continuous tape is wound about a series of turn around pins and in grooves in a magnetic core. A plurality of winding stacks are created, each transitioning to the next sequential stack by a transition tape portion extending from one turn around pin to the next turn around pin, which is position opposite with regard to the location of the pin on the magnetic core.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2019

Development of Short-Period Nb 3 Sn Superconducting Planar Undulators

NbTi-based superconducting undulators (SCUs) have been developed and proven to increase the brightness by an order of magnitude at high X-ray energies at the ANL's Advanced Photon Source (APS). Nb 3 Sn has the potential to further enhance the performance of SCUs. A new project, aiming to fabricate a full-length, 3-m-long Nb 3 Sn SCU, compatible with the storage ring, has started at the APS. To develop the technology, three Nb 3 Sn short prototype magnets were fabricated and tested in liquid helium. These prototypes were used to incrementally improve the original design. The final short model magnet reached 100% of the short sample limit. Here, the achieved current level in this magnet is 75% higher than what an NbTi wire can deliver.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2018

High performance superconducting undulator

A high performance superconducting undulator magnet is provided. The superconducting undulator magnet includes inset grooves in which magnetic poles are attached. The superconducting undulator magnet also includes clips for use in winding. The superconducting wire is wound such that the each revolution of the wire has a precise position within each of the grooves, the precise position being repeated in each groove. The superconducting undulator magnet provided will have a mechanical precision to preserve uniformity of the magnetic pole width and coil grooves. The undulator system provides uniformity of the undulator gap.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2018

DSP methods for correcting dispersion and pulse width effects during pulsed wire measurements

Measuring a magnetic field by applying electric current to a wire in a magnetic field for a short duration and recording the resulting travelling wave is referred to as the pulsed wire method. This technique is beneficial when other methods for acquiring magnetic field data are not feasible, e.g. small aperture limit of a Hall probe to measure an insertion device, or it can be used as a complement to other techniques. Data collected during pulsed wire measurements require corrections due to dispersion of the travelling wave and averaging effects of the current pulse duration. As a result, a flexible method for correcting dispersion has been developed using all pass digital filtering techniques and deconvolution is used to correct for pulse width averaging. Implementing the correction method is described along with the results of measuring a reference magnet and a 2.4-meter long undulator.

47 OTHER INSTRUMENTATION↗

DOE OSTI2017

High-temperature superconducting undulator magnets

Here, this paper presents test results on a prototype superconducting undulator magnet fabricated using 15% Zr-doped rare-earth barium copper oxide high temperature superconducting (HTS) tapes. On an 11-pole magnet we demonstrate an engineering current density, J e , of more than 2.1 kA mm -2 at 4.2 K, a value that is 40% higher than reached in comparable devices wound with NbTi-wire, which is used in all currently operating superconducting undulators. A novel winding scheme enabling the continuous winding of tape-shaped conductors into the intricate undulator magnets as well as a partial interlayer insulation procedure were essential in reaching this advance in performance. Currently, there are rapid advances in the performance of HTS; therefore, achieving even higher current densities in an undulator structure or/and operating it at temperatures higher than 4.2 K will be possible, which would substantially simplify the cryogenic design and reduce overall costs.

36 MATERIALS SCIENCE↗

DOE OSTI2016

Feasibility and electromagnetic analysis of a REBCO superconducting undulator

Recent advances in second-generation (2G) high temperature superconducting (HTS) coated conductors (CCs) have made them very attractive for new applications such as undulators. In this study, we have, for the first time, experimentally evaluated a design to validate applicability of 2G-HTS tapes for next generation undulator magnetic structures. A two-period undulator magnetic core was fabricated and 2G-HTS CCs were successfully wound onto the undulator core. The performance of the undulator magnetic structure was investigated and the highest engineering current density, J e , in such configuration reported yet was obtained. A new U-slit tape configuration was used to reduce the number of resistive joints and it was shown that with this new technique affordable levels of resistance values can be achieved for short length undulators. The ferromagnetic core was designed such as to accommodate winding the U-slit tapes. Finally, test results indicated that the winding and the soldering procedures are successful and do not deteriorate the performance of the 2G-HTS tapes.

2G-HTS↗