Engineering topics

Karchmer, A.

Publications and source records attributed to Karchmer, A..

11 records

NASA NTRS1983

The influence of inlet design on the aeroacoustic performance of a JT15D turbofan engine as measured in the NASA-Ames 40 x 80 foot wind tunnel

The influence of inlet design on the aeroacoustic performance of a JT15D turbofan engine was investigated in the NASA-Ames 40 x 80 ft wind tunnel. Four inlet designs representative of those found in commercial service were evaluated at a forward velocity of 80 kn. The inlet designs considered were selected to evaluate the importance of circumferential static pressure distortion (SPD) for a diffusing sound suppressing inlet and throat Mach number (Mth) for a hardwall inlet on the acoustic characteristics of the JT15D engine. Several speed points were studied simulating the operating conditions spanning approach to take-off. Results demonstrated that the dependency of the forward radiated noise on inlet aerodynamic design parameters was significant (about 5 dB) for the range of SPD (0.1-3.0%) and Mth (0.3-0.6) tested. The performance of the bulk absorber acoustic treatment used in the diffusing sound suppressing inlet is also discussed.

Holm, R. G.↗

NASA NTRS1981

Conditioned pressure spectra and coherence measurements in the core of a turbofan engine

Multiple and partial coherence functions and the corresponding conditioned coherent output spectra are computed between fluctuating pressures measured at two locations within the tailpipe of a turbofan engine and far-field acoustic pressure. The results are compared with the ordinary coherent output spectrum as obtained between a single tailpipe pressure measurement and the far-field acoustic pressure. The comparison indicates apparent additional 'coherent output' (i.e., core-noise) beyond that detectable with an ordinary coherence measurement, thus suggesting the tailpipe as a core-noise source region. Further evidence suggests, however, that these differences may be attributed to the presence of transverse acoustic modes in the tailpipe and that the tailpipe is not, in fact, a significant source region.

Karchmer, A.↗

NASA NTRS1981

Conditioned pressure spectra and coherence measurements in the core of a turbofan engine

Multiple and partial coherence functions and the corresponding conditioned coherent output spectra are computed between fluctuating pressures measured at two locations within the tailpipe of a turbofan engine and far-field acoustic pressure. The results are compared with the ordinary coherent output spectrum as obtained between a single tailpipe pressure measurement and the far-field acoustic pressure. The comparison indicates apparent additional "coherent output" (i.e., core-noise) beyond that detectable with an ordinary coherent measurement, thus suggesting the tailpipe as a core-noise source region. Further evidence suggests, however, that these differences may be attributed to the presence of transverse acoustic modes in the tailpipe and that the tailpipe is not, in fact, a significant source region.

Karchmer, A.↗

NASA NTRS1980

Core noise measurements from a small, general aviation turbofan engine

As part of a program to investigate combustor and other core noises, simultaneous measurements of internal fluctuating pressure and far field noise were made with a JT15D turbofan engine. Acoustic waveguide probes, located in the engine at the combustor, at the turbine exit and in the core nozzle wall, were used to measure internal fluctuating pressures. Low frequency acoustic power determined at the core nozzle exit corresponds in level to the far field acoustic power at engine speeds below 65% of maximum, the approach condition. At engine speeds above 65% of maximum, the jet noise dominates in the far field, greatly exceeding that of the core. From coherence measurements, it is shown that the combustor is the dominant source of the low frequency core noise. The results obtained from the JT15D engine were compared with those obtained previously from a YF102 engine, both engines having reverse flow annular combustors and being in the same size class.

Reshotko, M.↗

NASA NTRS1980

Core noise measurements from a small, general aviation turbofan engine

As part of a program to investigate combustor and other core noises, simultaneous measurements of internal fluctuating pressure and far field noise were made with a JT15D turbofan engine. Acoustic waveguide probes, located in the engine at the combustor, at the turbine exit and in the core nozzle wall, were used to measure internal fluctuating pressures. Low frequency acoustic power determined at the core nozzle exit corresponds in level to the far-field acoustic power at engine speeds below 65% of maximum, the approach condition. At engine speeds above 65% of maximum, the jet noise dominates in the far-field, greatly exceeding that of the core. From coherence measurements, it is shown that the combustor is the dominant source of the low frequency core noise. The results obtained from the JT15D engine were compared with those obtained previously from a YF102 engine, both engines having reverse flow annular combustors and being in the same size class.

Reshotko, M.↗

NASA NTRS1977

Combustor fluctuating pressure measurements in-engine and in a component test facility - A preliminary comparison

Combustor internal fluctuating pressure and far-field noise generated in a YF-102 turbofan engine are investigated; combustor internal measurements are also made in a duct-component test facility operating over a range of conditions encompassing those characteristic of the aircraft engine. Although directly measured spectra for the engine and the duct-component test facility show discrepancies, the results of coherence function, transfer function and phase relationship comparisons suggest that the internal dynamics of the combustor as an acoustic source may be preserved in a component test facility.

Reshotko, M.↗

NASA NTRS1977

Core noise measurements on a YF-102 turbofan engine

Core noise from a YF-102 high bypass ratio turbofan engine was investigated through the use of simultaneous measurements of internal fluctuating pressures and far field noise. Acoustic waveguide probes, located in the engine at the compressor exit, in the combustor, at the turbine exit, and in the core nozzle, were employed to measure internal fluctuating pressures. Spectra showed that the internal signals were free of tones, except at high frequency where machinery noise was present. Data obtained over a wide range of engine conditions suggest that below 60% of maximum fan speed the low frequency core noise contributes significantly to the far field noise.

Reshotko, M.↗

NASA NTRS1977

Combustor fluctuating pressure measurements in engine and in a component test facility: A preliminary comparison

In a program to investigate combustor noise, measurements were made with a YF-102 engine of combustor internal fluctuating pressure and far field noise. The relationship of far field noise to engine internal measurement was ascertained. The relationships between combustor internal measurements obtained in an engine and those obtained in a component test facility were established by using a YF-102 combustor, instrumented identically with that used in the engine tests. The combustor was operated in a component test facility over a range of conditions encompassing engine operation. A comparison of the directly measured spectra at corresponding locations in the two tests showed significant differences. The results of two point signal analyses within each combustor, were similar for both tests, indicating that the internal dynamics of the combustor as an acoustic source are preserved in a component test facility.

Reshotko, M.↗

NASA NTRS1976

Core noise source diagnostics on a turbofan engine using correlation and coherence techniques

Fluctuating pressure measurements at several locations within the core of a turbofan engine were made simultaneously with far-field acoustic measurements. Correlation and coherence techniques were used to determine the relative amplitude and phase relationships between core pressures at these various locations and between the core pressures and far-field acoustic pressure. The results indicate that the combustor is a low-frequency source region for acoustic propagation through the core nozzle and out to the far-field. Specifically, it was found that the relation between source pressure and the resulting sound pressure involves a 180 deg phase shift and an amplitude transfer function which varies approximately as frequency squared. This is shown to be consistent with a simplified model using fluctuating entropy as a source term.

Karchmer, A.↗

NASA NTRS1976

Lip noise generated by flow separation from nozzle surfaces

Flow separation from nozzle surfaces can be a source of significant noise in addition to the jet noise. When no flow separation region exists only jet noise is observed at every angle, for velocities down to 120 m/sec, with both low and high levels of initial turbulence. Intense nearly periodic turbulence and noise is caused by flow separation from the thin core nozzle lip of a coaxial nozzle. This can be described by a combination of aeolian tone and trailing edge noise theory. Noise caused by flow separation from the surfaces of other nozzle geometries has somewhat different characteristics.

Olsen, W.↗

NASA NTRS1975

Lip noise generated by flow separation from nozzle surfaces

The results of a series of experiments, performed to investigate flow separation and classic lip noise and to aid in understanding aeroacoustic noise generation are presented. Several types of nozzle-lip configurations were used to study the high frequency noise generated by small regions of flow separation at the nozzle lip. These included coaxial nozzles, and circular and slot nozzles with splitter plates. The jet flow velocity was varied and far field noise was measured for all nozzle-lip geometries (coaxial and splitter plate). The effect of a velocity difference across the lip of the coaxial nozzle and the splitter plate on the far field noise was also measured. Finally, an effort was made to find means to reduce the high frequency noise caused by flow separation at the lip.

Olsen, W.↗