Engineering Papers⌕ Search

Engineering topics

Kannel, J. W.

Publications and source records attributed to Kannel, J. W..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Evaluation of feasibility of measuring EHD film thickness associated with cryogenic fluids

The feasibility of measuring elastohydrodynamic (EHD) films as formed with a cryogenic (LN2) fluid is evaluated. Modifications were made to an existing twin disk EHD apparatus to allow for disk lubrication with liquid nitrogen. This disk apparatus is equipped with an X-ray system for measuring the thickness of any lubricant film that is formed between the disks. Several film thickness experiments were conducted with the apparatus which indicate that good lubrication films are filmed with LN2. In addition to the film thickness studies, failure analyses of three bearings were conducted. The HPOTP turbine end bearings had experienced axial loads of 36,000 to 44,000 N (8,000 to 10,000 lb). High continuous radial loads were also experienced, which were most likely caused by thermal growth of the inner race. The resulting high internal loads caused race spalling and ball wear to occur.

Kannel, J. W.↗
NASA NTRS1983

Evaluation of outer race tilt and lubrication on ball wear and SSME bearing life reductions

Several aspects of the SSME bearing operation were evaluated. The possibility of elastohydrodynamics (EHD) lubrication with a cryogenic fluid was analyzed. Films as thick as .61 microns were predicted with one theory which may be thick enough to provide hydrodynamic support. The film formation, however, is heavily dependent on good surface finish and a low bulk bearing temperature. Bearing dynamics to determine if the radial stiffness of a bearing which are dependent on bearing misalignment were analyzed. Four ball tests were conducted at several environmental conditions from an LN2 bath to 426 C in air. Surface coatings and ball materials are evaluated. Severe wear and high friction are measured for all ball materials except when the balls have surface lubricant coatings.

Kannel, J. W.↗
NASA NTRS1982

Evaluation of bearing mounting design and excessive wear phenomena

The effect of bearing thermal growth on the effectiveness of the bearing preload springs on the space shuttle main engine high pressure oxygen turbopump (SSME HPTOP) were examined. The SSME HPTOP turbine end bearings, preload spring, and bearing mounting design were evaluated relative to spalling, excessive ball wear, possible thermal problems, and cage delamination. The magnitude of the thermal stresses required to cause high levels of ball wear were calculated. Plots of maximum sheer stress and maximum reversing shear versus the axial load for the 57 mm SSME HPTOP bearing were created. A plot of the bearing thermal growth versus preload spring deflection was generated. It was determined that metallic wear, rather than thermal growth, caused enlargement of the contact zone between ball and races, that high fatigue-inducing shear stresses are generated under increased loads, and that at temperatures between 100 and 150 deg C, the springs bottom out and very high loads are developed in the bearing. Allowance for adequate spring movement after assembly is recommended.

Kannel, J. W.↗
NASA NTRS1981

Study of methods for applying and enhancing transfer film coatings of polytetrafluoroethylene (PTEE) to Space Shuttle Main Engine (SSME) High Pressure Oxygen Turbo Pump (HPOTP) bearings

Machines were constructed and evaluated for burnishing polytetrafluoroethylene on balls for use in the high pressure oxygen turbopump (HPOTP). The most positive performance was obtained with single-ball burnishing, but one technique for burnishing three balls simultaneously holds promise. Evaluations of the coatings in a HPOTP bearing of earlier design (employed smaller diameter balls) showed very little life enhancement before high torque and ball and race wear initiated. Other coating techniques, such as molybdenum disulfide combined with PTFE transfer films, hold promise for providing the more durable quantities of solid lubricant needed for the bearings.

Kannel, J. W.↗
NASA NTRS1981

Stress evaluations under rolling/sliding contacts

The state of stress beneath traction drive type of contacts were analyzed. Computing stresses and stress reversals on various planes for points beneath the surface were examined. The effect of tangential and axial friction under gross slip conditions is evaluated with the models. Evaluations were performed on an RC (rolling contact) tester configuration and it is indicated that the classical fatigue stresses are not altered by friction forces typical of lubricated contact. Higher values of friction can result in surface shear reversal that exceeds the stresses at the depth of maximum shear reversal under rolling contact.

Kannel, J. W.↗
NASA NTRS1981

Transfer film evaluation for shuttle engine turbopump bearing

A series of low speed experiments to evaluate the possible occurrence of transfer film lubrication and the effectiveness of burnished films in the shuttle spacecraft main engine thrust bearings were conducted. No evidence of transfer film lubrication was evident, although this could have been the result of the (used) condition of the bearing. Burnished films of either Teflon or Rulon were found to greatly enhance the performance of the bearing. Crush load experiments indicated that the bearing ultimate load capability is on the order of 489,000 N (110,000 pounds). The effect of ball (as well as race) burnishing techniques on bearing performance, different types of burnished films, and transfer film formation are suggested for further study.

Kannel, J. W.↗
NASA NTRS1980

Evaluation of axial lock-up of space shuttle main engine bearings from high pressure oxygen turbopump

The mainshaft support bearings of long life turbopumps for use on the space shuttle were evaluated to determine possible causes of failure. Specific aspects examined include the sensitivity of 15 degree versus 25 degree contact angle bearings with regard to heat damage and thermal runaway, the L/D aspects of the turbine end bearing pair with regard to hang-up due to cocking, the hang-up required to support a 44.5 KN axial load without cartridge slipping, the outer race growth as a result of a 44.5 KN axial load, and bearing torque as a function of axial load. Results indicate that hang-up of the cartridge due to bearing heating is a serious problem especially if poor lubrication of the bearing occurs and that race growth due to axial load can contribute to cartridge lock-up. The experimental evaluation of bearing performance under axial loads indicates that the bearing torque is a strong function of surface lubrication.

Kannel, J. W.↗
NASA NTRS1980

SSME turbopump bearing analytical study

Three shuttle pump bearings operating under severe overspeed and shut-down conditions are evaluated. The specific parameters investigated include outer race stresses, cage stresses, cage-race drag, bearing heating, and crush loading. A quasi-dynamic version of the BASDAP computer code was utilized which involved the calculation of ball-race forces (inner and outer), contact pressures, contact dimensions, and contact angles as a function of (1) axial load, (2) radial load, and (3) centrifugal load on the bearing. Generally, radial loads on the order of 13,300 N (3000 pounds) per bearing or 26,700 N (6000 pounds) per bearing pair, could be expected to cause severe problems to any of the bearings with a 17,800 N (4000 pounds) axial load. Further, when possible temperature excursions are considered, even a load of 8900 N (2000 pounds) may be excessive. However, high momentary radial loads with a 3800 N (850 pounds) axial load would not be anticipated to cause catastrophic failure of the fuel pump bearing.

Kannel, J. W.↗
NASA NTRS1980

Evaluation of space shuttle main engine bearings from high pressure oxygen turbopump 9008

Two used turbopump mainshaft support bearings were examined to determine steps needed to achieve turbopump lifetimes of 27,000 seconds. The two bearings, which had been run in a high pressure oxygen turbopump, are angular contact ball bearings, applied as a preloaded pair, locked to the shaft, inner race rotating, with the outer races unrestrained axially. Examination showed that both bearings had been subjected to overloads, leading to fatigue spalling on the races and balls and advanced retainer wear. This is clear evidence of unintended high internal loads in the high pressure oxygen pump which would lead to complete bearing failure and extensive secondary pump damage. Action must be taken to reduce the applied bearing loads or to incorporate bearings of sufficient size to withstand the high loads.

Dufrane, K. F.↗
NASA NTRS1979

Evaluation of SSME high pressure liquid oxygen turbopump bearings

Examination of the bearings produced conclusive evidence that a very high axial load was applied to bearing 8517903 during a significant portion of the service time. The high loads caused serious ball and race wear and surface fatigue pitting. In all likelihood, continued operation of this bearing with the high axial load would have caused increasing deterioration and catastrophic failure. In contrast, bearing 8517900 showed much less deterioration and probably had experienced only the axial loads deliberately applied by the preload spring. Bearing 8517900 represents the best-case operation with the loads controlled to the levels intended in the design. Fatigue life calculations on bearing 8517903 with an axial load of 27,000 N showed the intolerance of the bearing to such load levels.

Dufrane, K. F.↗
NASA NTRS1979

Determination of lubricant selection based on elastohydrodynamic film thickness and traction measurement

The project was conducted to aid in the development of an elastohydrodynamic specification for military lubricants. Experiments were conducted with a rolling disk apparatus designed to simulate a bearing or gear type contact. Measurements included lubricant film thickness, lubricant breakdown and traction for a range of loads, speeds, temperatures, and surface roughnesses. Several lubricants were used in the investigations including a traction fluid, two synthetic paraffinic lubricants and several lubricants conforming to MIL-L 7808 and 23699 specifications. Recommendations regarding an EHD specification are included.

Dow, T. A.↗
NASA NTRS1978

Evaluation of worn SSME low pressure liquid oxygen turbopump bearing

The larger of two ball bearings used to support the rotor of the low pressure liquid oxygen turbopump in each of the shuttle main engines was analyzed to identify the cause of severe internal wear. The actual operating loads were calculated along with their direction and length of time at each load based on the size and location of the race contact paths. It is suggested that the engine component design be modified to reduce bearing stress and enhance lubrication.

Dufrane, K. F.↗
NASA NTRS1978

Evaluation of shuttle turbopump bearings

Because the high pressure turbopumps used on the space shuttle main engine (SSME) are high speed machines and rotor dynamics analysis of these units is very complicated, it was considered necessary to verify calculated turbomachinery shaft bearing loads by analysis of ball bearing load tracks. This report presents the methods used and the results of load track analysis on one set of bearings removed from a high pressure liquid oxygen turbopump which had been subjected to SSME static firing tests. This type of analysis was found useful in determining bearing operating conditions and for verifying rotor dynamics computer models.

Dufrane, K. F.↗
NASA NTRS1975

Elastohydrodynamic lubrication in an instrument ball-bearing

The paper deals with experimental measurement of bearing torque and 'percentage of lubrication' in instrument size (R6) bearings. The primary parameter found to affect bearing performance for several lubricant investigations is base viscosity. Inference of EHD film thickness is made from the percentage of film measurements which are compared with X-ray data. A reasonable correlation between the two types of data is presented, thereby, paving the way toward the use of the more universally applicable percentage of film measurements for the determination of EHD conditions in real bearing systems.

Kannel, J. W.↗
NASA NTRS1975

Effect of longitudinal surface finish on elastohydrodynamic lubrication

The effect of longitudinal-lay surface finish on the elastohydrodynamic film thickness and the percentage of film between rolling disks in contact were evaluated using a rolling disk apparatus. Film thickness was measured by transmitted X-rays, and percentage of film was monitored by an alternating-current continuity circuit. Disk finish was varied on both the crowned upper disk and the cylindrical lower disk. A type-2 ester and a synthetic paraffinic oil were used as lubricants. It was shown that the roughness with longitudinal lay has a deleterious effect on both film thickness and percentage of film. Measured film thicknesses for the two lubricants were comparable at equivalent test conditions. The percentage of film where a change in surface topography was observed was approximately 20 percent for the synthetic paraffinic oil and 10 percent for the type-2 ester.

Dow, T. A.↗
NASA NTRS1971

Elastohydrodynamic film thickness measurements with advanced ester, fluorocarbon, and polyphenyl ether lubricants to 589 K (600 F)

Elastohydrodynamic (EHD) film thicknesses have been measured, by means of an X-ray technique, under conditions that closely simulate the ball-race contact in advanced turbine engine thrust bearings. The experiments were conducted with a rolling-disk machine using disks which yield a contact zone similar to that in the actual bearing. Both the rolling and spinning motions of the ball relative to the race were simulated by the apparatus. Four lubricants were evaluated at temperatures to 600 F and maximum Hertz stresses to 350,000 psi. The X-ray film thickness data correlated well with observations of surface distress (or lack thereof) in full-scale bearing tests with the same lubricants under similar conditions of temperature and load. The predicted variation of film thickness with speed and viscosity as verified, although the magnitude of measured film thickness was generally one-half to one-third of predicted values. An effect of stress greater than predicted was consistently observed in the higher stress range.

Parker, R. J.↗