Engineering Papers⌕ Search

Engineering topics

Kang, S -H

Publications and source records attributed to Kang, S -H.

Study of Li{sub 1+x}(Mn{sub 4/9}Co{sub 1/9}Ni{sub 4/9}){sub 1-x}O{sub 2} cathode materials for vehicle battery applications.

Li{sub 1+x}(Mn{sub 4/9}Co{sub 1/9}Ni{sub 4/9}){sub 1-x}O{sub 2} with two lithium content (x = 0 and 0.05) has been synthesized using coprecipitated (Mn{sub 4/9}Co{sub 1/9}Ni{sub 4/9})(OH){sub 2} and their electrochemical properties have been investigated. Compared with the x = 0 material, the lithium-rich material (x = 0.05) exhibited superior electrochemical properties. When cycled between 2.5 and 4.4 V, the Li/Li{sub 1.05}(Mn{sub 4/9}Co{sub 1/9}Ni{sub 4/9}){sub 0.95}O{sub 2} cells showed high first-cycle coulombic efficiency (93%), reversible discharge capacity of 187 mAh/g at C/12 with 99% capacity retention after 40 cycles, and excellent rate performance (86% of C/12 rate at 5 C discharge current). The Li{sub 1.05}(Mn{sub 4/9}Co{sub 1/9}Ni{sub 4/9}){sub 0.95}O{sub 2} electrode also showed a full-cell pulse power characteristics (5 C discharge pulse) comparable to Li{sub 1.05}(Mn{sub 1/3}Co{sub 1/3}Ni{sub 1/3}){sub 0.95}O{sub 2} electrode and better thermal stability at charged state (4.4 V) than charged LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} (4.2 V). Using a battery design and cost model developed in-house, calculations found battery packs with Li{sub 1.05}(Mn{sub 4/9}Co{sub 1/9}Ni{sub 4/9}){sub 0.95}O{sub 2} as the positive electrode to be of lower cost and higher energy density than those with LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} and Li{sub 1.05}(Mn{sub 1/3}Co{sub 1/3}Ni{sub 1/3}){sub 0.95}O{sub 2} electrodes. The experimental and modeling results obtained in this work suggest Li{sub 1.05}(Mn{sub 4/9}Co{sub 1/9}Ni{sub 4/9}){sub 0.95}O{sub 2} to be a promising cathode material for vehicle battery applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural Complexity of Layered-spinel Composite Electrodes for Li-ion Batteries

The complexity of layered-spinel yLi{sub 2}MnO{sub 3} {center_dot} (1-y)Li{sub 1+x}Mn{sub 2-x}O{sub 4} (Li:Mn = 1.2:1; 0 = x = 0.33; y = 0.45) composites synthesized at different temperatures has been investigated by a combination of x-ray diffraction (XRD), x-ray absorption spectroscopy (XAS), and nuclear magnetic resonance (NMR). While the layered component does not change substantially between samples, an evolution of the spinel component from a high to a low lithium excess phase has been traced with temperature by comparing with data for pure Li{sub 1+x}Mn{sub 2-x}O{sub 4}. The changes that occur to the structure of the spinel component and to the average oxidation state of the manganese ions within the composite structure as lithium is electrochemically removed in a battery have been monitored using these techniques, in some cases in situ. Our 6Li NMR results constitute the first direct observation of lithium removal from Li{sub 2}MnO{sub 3} and the formation of LiMnO{sub 2} upon lithium reinsertion.

25 ENERGY STORAGE↗

Li{sub 2}O removal from Li{sub 5}FeO{sub 4} - a cathode precursor for lithium-ion batteries.

Lithium has been extracted both electrochemically and chemically from the defect antifluorite-type structure, Li{sub 5}FeO{sub 4} (5Li{sub 2}O {center_dot} Fe{sub 2}O{sub 3}). The electrochemical data show that four lithium ions can be removed from Li{sub 5}FeO{sub 4} between 3.5 and 4.5 V. vs Li{sup 0}. X-ray absorption spectroscopy (XAS) data of electrochemically delithiated samples show evidence of some Fe{sup 3+} to Fe{sup 4+} oxidation during the initial charge. On the other hand, XAS data of chemically delithiated samples show no evidence of Fe{sup 3+} to Fe{sup 4+} oxidation, but rather a change in coordination of the Fe{sup 3+} ions from tetrahedral to octahedral coordination, suggesting that lithium extraction from Li{sub 5}FeO{sub 4} is accompanied predominantly by the release of oxygen, the net loss being lithia (Li{sub 2}O); the residual lithium-iron-oxide product has a Fe{sub 2}O{sub 3}-rich composition. The high lithium content in Li{sub 5}FeO{sub 4} renders it an attractive cathode precursor for loading the graphite (C{sub 6}) anode of lithium-ion electrochemical cells with sufficient lithium to enable the discharge of a charged component in the parent cathode, Li{sub 1.2}V{sub 3}O{sub 8}, as well as the residual Fe{sub 2}O{sub 3}-rich component. The electrochemical behavior of C{sub 6}/Li{sub 5}FeO{sub 4}?Li{sub 1/2}V{sub 3}O{sub 8} lithium-ion cells is compared to C{sub 6}/Li{sub 2}MnO{sub 3}?Li{sub 1.2}V{sub 3}O{sub 8} cells containing a layered Li{sub 2}MnO{sub 3} (Li{sub 2}O {center_dot} MnO{sub 2}) cathode precursor with a lower Li{sub 2}O content, from which lithia can be extracted at higher potentials, typically >4 V vs metallic lithium. The ability to remove Li{sub 2}O electrochemically from metal oxide host structures with a high lithium content, such as Li{sub 5}FeO{sub 4}, has implications for Li-air cells.

74 ATOMIC AND MOLECULAR PHYSICS↗

Enhancing the rate capability of high capacity xLi{sub 2}MnO{sub 3} {sm_bullet} (1-x)LiMO{sub 2} (M=Mn, Ni, Co) electrodes.

The rate capability of high capacity xLi{sub 2}MnO{sub 3} {center_dot} (1 - x)LiMO{sub 2} (M = Mn, Ni, Co) electrodes for lithium-ion batteries has been significantly enhanced by stabilizing the electrode surface by reaction with a Li-Ni-PO{sub 4} solution, followed by a heat-treatment step. Reversible capacities of 250 mAh/g at a C/11 rate, 225 mAh/g at C/2 and 200 mAh/g at C/1 have been obtained from 0.5Li{sub 2}MnO{sub 3} {center_dot} 0.5LiNi{sub 0.44}Co{sub 0.25}Mn{sub 0.31}O{sub 2} electrodes between 4.6 and 2.0 V. The data bode well for their implementation in batteries that meet the 40-mile range requirement for plug-in hybrid vehicles.

25 ENERGY STORAGE↗

Examining the solid electrolyte interphase on binder-free graphite electrodes.

The solid electrode interphase (SEI) on graphite electrodes is important to the performance, calendar life, and safety characteristics of lithium-ion cells. This article examines the SEI formed on binder-free graphite electrodes prepared by electrophoretic deposition. X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis data were obtained on electrodes cycled in cells containing four electrolytes comprising ethylene carbonate: ethylmethyl carbonate (3:7 by weight) solvent and 1.2 M LiPF{sub 6}, 1 M LiF{sub 2}BC{sub 2}O{sub 4}, 1 M LiBF{sub 4}, or 0.7 M LiB(C{sub 2}O{sub 4}){sub 2} salt. Our observations suggest that, in addition to solvent reduction, the reduction of electrolyte salts plays an important role in SEI formation. Mechanisms to account for the formation of these SEI constituents are included in the article.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

First-cycle irreversibility of layered Li-Ni-Co-Mn oxide cathode in Li-ion batteries.

The first-cycle irreversibility of Li{sub 1.048}(Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}){sub 0.952}O{sub 2} (LiMO{sub 2}) cathode material in lithium and lithium-ion cells has been studied using galvanostatic cycling and in situ synchrotron X-ray diffraction. The so-called 'lost capacity' of a Li/LiMO{sub 2} cell observed during initial cycle in conventional voltage ranges (e.g., 3.0-4.3 V) could be completely recovered by discharging the cell to low voltages (<2 V). During the deep discharge, the lithium cell exhibited an additional voltage plateau, which is believed to result from the formation of Li{sub 2}MO{sub 2}-like phase on the oxide particle surface due to very sluggish lithium diffusion in Li{sub 1-{Delta}}MO{sub 2} with {Delta} {yields} 0 (i.e., near the end of discharge). Voltage relaxation curve and in situ X-ray diffraction patterns, measured during relaxation of the lithium cell after deep discharge to obtain 100% cycle efficiency, suggested that the oxide cathode returned to its original state after the following two-step relaxation processes: relatively quick disappearance of the Li{sub 2}MO{sub 2}-like phase on the particle surface, followed by slow lithium diffusion in the layered structure. Experiments conducted in Li{sub 4}Ti{sub 5}O{sub 12}/LiMO{sub 2} lithium-ion cells confirmed that the physical loss of lithium (via surface film formation or parasitic electrochemical reactions, etc.) from LiMO{sub 2} was negligible up to an oxide voltage of 4.3 V vs. Li{sup +}/Li.

43 PARTICLE ACCELERATORS↗

Local structure and composition studies of Li{sub 1.2}Ni{sub 0.2}Mn{sub 0.6}O{sub 2} by analytical electron microscopy.

Positive electrodes for Li-ion batteries based on Li[Li{sub 1/3-2x/3}Ni{sub x}Mn{sub 2/3-x/3}]O{sub 2} (0 {le} x {le} 0.5) compounds are of significant interest because of their ability to deliver reversible capacities exceeding 200 mAh g{sup -1}. In this article we describe the examination of Li{sub 1.2}Ni{sub 0.2}Mn{sub 0.6}O{sub 2} (x = 0.2 in Li[Li{sub 1/3-2x/3}Ni{sub x}Mn{sub 2/3-x/3}]O{sub 2}) samples by X-ray diffraction (XRD), high-resolution electron microscopy (HREM), scanning transmission electron microscopy (STEM), electron diffraction, X-ray energy dispersive spectroscopy (EDS), and electron energy loss spectroscopy (EELS). The studies were conducted on freshly prepared oxides, and on oxide electrodes that were electrochemically activated by cycling twice between 4.8 and 2.0 V vs. Li{sup +}/Li. Rectangular and parallelogram shaped dot arrays with a spacing of 0.43 nm observed in HREM and STEM images along the [10{bar 1}0] zone axis, as well as streaks at 1/3 n (11{bar 2}0) (n = integer) positions in corresponding electron diffraction patterns, indicated ordering of Li-ions in the transition-metal (TM) (0 0 0 1) layers following several stacking sequences, bounded by stacking faults, along the c-axis. Chemical analysis by EDS and EELS showed that Mn, Ni and O were present in all portions of the samples examined; no evidence of elemental segregation was observed either within the grains or at grain boundaries. The Li ordering on TM planes was significantly weaker but still discernable upon electrochemical activation of the oxide samples.

25 ENERGY STORAGE↗

Eeffect of electrolyte composition on initial cycling and impedance characteristics of lithium-ion-cells.

Hybrid-electric vehicles require lithium-battery electrolytes that form stable, low impedance passivation layers to protect the electrodes, while allowing rapid lithium-ion transport under high current charge/discharge pulses. In this article, we describe data acquired on cells containing LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2}-based positive electrodes, graphite-based negative electrodes, and electrolytes with lithium hexafluorophosphate (LiPF{sub 6}), lithium tetrafluoroborate (LiBF{sub 4}), lithium bis(oxalato)borate (LiBOB) and lithium difluoro(oxalato) borate (LiF{sub 2}OB) salts. The impedance data were collected in cells containing a Li-Sn reference electrode to determine effect of electrolyte composition and testing temperature on individual electrode impedance. The full cell impedance data showed the following trend: LiBOB > LiBF{sub 4} > LiF{sub 2}OB > LiPF{sub 6}. The negative electrode impedance showed a trend similar to that of the full cell; this electrode was the main contributor to impedance in the LiBOB and LiBF{sub 4} cells. The positive electrode impedance values for the LiBF{sub 4}, LiF{sub 2}OB, and LiPF{sub 6} cells were comparable; the values were somewhat higher for the LiBOB cell. Cycling and impedance data were also obtained for cells containing additions of LiBF{sub 4}, LiBOB, LiF{sub 2}OB, and vinylene carbonate (VC) to the EC:EMC (3:7 by wt.) + 1.2 M LiPF{sub 6} electrolyte. Our data indicate that the composition and morphology of the graphite SEI formed during the first lithiation cycle is an important determinant of the negative electrode impedance, and hence full cell impedance.

36 MATERIALS SCIENCE↗

Investigating the low-temperature impedance increase of lithium-ion cells.

Low-temperature performance loss is a significant barrier to commercialization of lithium-ion cells in hybrid electric vehicles. Increased impedance, especially at temperatures below 0 C, reduces the cell pulse power performance required for cold engine starts, quick acceleration, or regenerative braking. Here we detail electrochemical impedance spectroscopy data on binder- and carbon-free layered-oxide and spinel-oxide electrodes, obtained over the +30 to ?30 C temperature range, in coin cells containing a lithium-preloaded Li{sub 4/3}Ti{sub 5/3}O{sub 4} composite (LTOc) counter electrode and a LiPF{sub 6}-bearing ethylene carbonate/ethyl methyl carbonate electrolyte. For all electrodes studied, the impedance increased with decreasing cell temperature; the increases observed in the midfrequency arc dwarfed the increases in ohmic resistance and diffusional impedance. Our data suggest that the movement of lithium ions across the electrochemical interface on the active material may have been increasingly hindered at lower temperatures, especially below 0 C. Low-temperature performance may be improved by modifying the electrolyte-active material interface (for example, through electrolyte composition changes). Increasing surface area of active particles (for example, through nanoparticle use) can lower the initial electrode impedance and lead to lower cell impedances at -30 C.

74 ATOMIC AND MOLECULAR PHYSICS↗

Stabilization xLi{sub 2}MnO{sub 3}{sm_bullet}(1-x)LiMO{sub 2} electrode surfaces (M=Mn, Ni, Co) with mildly acidic, fluorinated solutions.

It has been demonstrated previously that Li{sub 2}MnO{sub 3}-stabilized LiMO{sub 2} electrodes [xLi{sub 2}MnO{sub 3} {sm_bullet} (1?x)LiMO{sub 2}, M=Mn, Ni, Co] can provide anomalously high electrochemical capacities ({approx}250 mAh/g) if charged to high potentials (>4.6 V). High-voltage charging results in an irreversible capacity loss on the initial charge/discharge cycle; it also damages the electrode surface, leading to a high cell impedance. In this paper, we report that preconditioning 0.1Li{sub 2}MnO{sub 3} {sm_bullet} 0.9LiMn{sub 0.256}Ni{sub 0.372}Co{sub 0.372}O{sub 2} electrode powders [alternatively Li{sub 1.048}(Mn{sub 0.333}Ni{sub 0.333}Co{sub 0.333}){sub 0.952}O{sub 2} in Li{sub 1+x}M{sub 1?x}O{sub 2} notation] with extremely mild acidic solutions of NH{sub 4}PF{sub 6}, (NH{sub 4}){sub 3}AlF{sub 6}, and NH{sub 4}BF{sub 4} salts in water and methanol (pH 6-6.5) leads to remarkable cycling stability of both lithium half-cells and full lithium-ion cells when repeatedly charged to high voltages ({ge} 4.5 V). The enhanced electrochemical performance is attributed to stabilized electrode surfaces that are etched and passivated by fluorinated species. The low-temperature behavior of unconditioned and preconditioned electrodes is presented.

10 SYNTHETIC FUELS↗