Engineering Papers⌕ Search

Engineering topics

Kang, Qinjun

Publications and source records attributed to Kang, Qinjun.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Lattice Boltzmann Modeling of Drying of Porous Media Considering Contact Angle Hysteresis

Drying of porous media is governed by a combination of evaporation and movement of the liquid phase within the porous structure. Contact angle hysteresis induced by surface roughness is shown to influence multi-phase flows, such as contact line motion of droplet, phase distribution during drainage and coffee ring formed after droplet drying in constant contact radius mode. However, the influence of contact angle hysteresis on liquid drying in porous media is still an unanswered question. Lattice Boltzmann model (LBM) is an advanced numerical approach increasingly used to study phase change problems including drying. In this paper, based on a geometric formulation scheme to prescribe contact angle, we implement a contact angle hysteresis model within the framework of a two-phase pseudopotential LBM. The capability and accuracy of prescribing and automatically measuring contact angles over a large range are tested and validated by simulating droplets sitting on flat and curved surfaces. Afterward, the proposed contact angle hysteresis model is validated by modeling droplet drying on flat and curved surfaces. Then, drying of two connected capillary tubes is studied, considering the influence of different contact angle hysteresis ranges on drying dynamics. Finally, the model is applied to study drying of a dual-porosity porous medium, where phase distribution and drying rate are compared with and without contact angle hysteresis. The proposed model is shown to be capable of dealing with different contact angle hysteresis ranges accurately and of capturing the physical mechanisms during drying in different porous media including flat and curved geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pore-scale simulation of drying in porous media using a hybrid lattice Boltzmann: pore network model

In this work, a hybrid method coupling a pseudo-potential lattice Boltzmann model (LBM) and a pore network model (PNM) to simulate drying in porous media is proposed. Based on the watershed method, the porous medium is firstly decomposed into pore regions. According to the liquid–vapor phase distribution at a given time, the pore regions are further divided into four pore types, namely two-phase pores where a liquid–vapor interface exists, buffer pores next to the two-phase pores, single-liquid and single-vapor phase pores. The pseudo-potential LBM is used in the two-phase and buffer pores to simulate liquid drying and track the movement of the interfaces, while the single-phase PNM simulations are conducted in the buffer and single-phase pores to simulate vapor or liquid flow. LBM and PNM are coupled in the buffer pores through exchange of boundary information. The hybrid method is applied to simulate liquid drying in a porous medium. The whole-domain LBM simulation is considered as the reference solution to validate the hybrid method. Liquid saturation variation during the drying process and detailed phase and pressure distributions obtained by the two methods match quite well, demonstrating the accuracy of the hybrid method. For the specific case studied, the hybrid method saves more than 60% computational time compared to the whole-domain LBM simulation. In addition, the speedup of the hybrid method becomes more significant for a larger computational domain. In summary, the hybrid method developed in this work combines the accuracy of LBM and the efficiency of PNM to simulate drying in porous media at pore scale and can lead to significant reduction of computation time, thus allowing the pore-scale consideration of drying in larger porous systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Computationally Efficient Multiscale Neural Networks Applied to Fluid Flow in Complex 3D Porous Media

Abstract The permeability of complex porous materials is of interest to many engineering disciplines. This quantity can be obtained via direct flow simulation, which provides the most accurate results, but is very computationally expensive. In particular, the simulation convergence time scales poorly as the simulation domains become less porous or more heterogeneous. Semi-analytical models that rely on averaged structural properties (i.e., porosity and tortuosity) have been proposed, but these features only partly summarize the domain, resulting in limited applicability. On the other hand, data-driven machine learning approaches have shown great promise for building more general models by virtue of accounting for the spatial arrangement of the domains’ solid boundaries. However, prior approaches building on the convolutional neural network (ConvNet) literature concerning 2D image recognition problems do not scale well to the large 3D domains required to obtain a representative elementary volume (REV). As such, most prior work focused on homogeneous samples, where a small REV entails that the global nature of fluid flow could be mostly neglected, and accordingly, the memory bottleneck of addressing 3D domains with ConvNets was side-stepped. Therefore, important geometries such as fractures and vuggy domains could not be modeled properly. In this work, we address this limitation with a general multiscale deep learning model that is able to learn from porous media simulation data. By using a coupled set of neural networks that view the domain on different scales, we enable the evaluation of large ( $$>512^3$$ > 512 3 ) images in approximately one second on a single graphics processing unit. This model architecture opens up the possibility of modeling domain sizes that would not be feasible using traditional direct simulation tools on a desktop computer. We validate our method with a laminar fluid flow case using vuggy samples and fractures. As a result of viewing the entire domain at once, our model is able to perform accurate prediction on domains exhibiting a large degree of heterogeneity. We expect the methodology to be applicable to many other transport problems where complex geometries play a central role.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Machine-learning predictions of the shale wells’ performance

The ultra-low permeability nature of shale reservoirs leads to an extended linear flow and necessitates horizontal wells with multi-stage engineered fractures to efficiently extract hydrocarbons resources. These artificially-generated and naturally-occurring fractures form complex networks that create complex flow regimes which control oil production. These fractures are neither identical nor equally-spaced, which leads to a production profile with a masked onset of the boundary-dominated flow. The combination of the extended linear flow with the indeterminate onset of the boundary-dominated flow challenges the current deterministic analytic approaches to forecast the estimated ultimate recovery (EUR). In this work, we propose a novel machine-learning approach which overcomes these challenges and provides reliable EUR estimates based on field-wide analyses. We implement a novel unsupervised machine learning (ML) methodology, which allows for automatic identification of the optimal number of features (signals) present in the data based on non-negative matrix/tensor factorization coupled with k-means clustering incorporating regularization and physics constraints. In the presented analyses, the input data to the ML algorithm is the available (public) production history from the field collected at existing unconventional reservoirs. We validate our approach through hindcasting of the production data, where we achieved an excellent agreement. In addition, our approach is able to identify the poorly-performing wells, which could benefit from early refracing. Our approach provides fast and accurate estimations of the well performance without presumptions about the state of the well or the flow regime.

03 NATURAL GAS↗
DOE OSTI2021

Spontaneous imbibition in a square tube with corner films: theoretical model and numerical simulation

Spontaneous imbibition in an angular tube with corner films is a fundamental problem in many scientific and engineering processes. In this paper, a modified interacting capillary bundle model is developed to describe the liquid imbibition dynamics in a square tube with corner films. The square tube is decomposed into several interacting sub-capillaries and the local capillary pressure in each sub-capillary is derived based on the specific shape of its meniscus. The conductance of each sub-capillary is calculated using single-phase lattice Boltzmann simulation. The modified interacting capillary bundle model and color-gradient lattice Boltzmann method are used to simulate the liquid imbibition dynamics in the square tube with different fluid properties. The predictions by the modified interacting capillary bundle model match well with the lattice Boltzmann simulation results for different conditions, demonstrating the accuracy and robustness of the interacting capillary bundle model to describe the imbibition dynamics with corner films. In addition, the interacting capillary bundle model is helpful to investigate the mechanisms during spontaneous imbibition and the influences of fluid viscosity, surface tension, wetting phase contact angle and gravity on imbibition dynamics. Finally, a universal scaling law of imbibition dynamics for the main meniscus is developed and the scaling law for arc meniscus is also analyzed.

42 ENGINEERING↗
DOE OSTI2021

Three influential factors on colloidal nanoparticle deposition for heat conduction enhancement in 3D chip stacks

Thermal management is one of the major challenges facing the development of three-dimensional (3D) chip stacks. Recently, experimental studies have shown that neck-based thermal structure (NTS) between chip layers formed by drying of colloidal suspension in cavity filled with micro-size particles can improve the vertical heat conduction threefold. However, a deep understanding of the mechanisms of neck formation and its influence on heat conduction is still lacking. In this paper, we numerically study the effects of three parameters, i.e., initial nanoparticle concentration, drying temperature and chip surface wettability on neck formation between filler particles and on the resulting heat conduction of the NTS. With increasing nanoparticle concentration, the size and number of necks increase, resulting in an increased effective thermal conductivity (ETC) of NTS. The drying temperature is found to have only little influence on the ETC of resultant NTS, while the neck size and spatial distribution become more uniform at higher drying temperature. When reducing the wettability of the top and bottom surfaces of the cavity, the necks shrink in size until completing evacuating at the top and bottom layers, while the size of the necks between filler particles in the middle height of the cavity expands slowly. In consequence, the ETC of NTS drops at an increasing rate. Being able to reveal the underlying multiple mechanisms of two-phase flow, phase change and heat transport, the current numerical study suggests optimal values for the deposition process, with initial nanoparticle concentration over 0.8%, a drying temperature of 60°C and a uniform contact angle of 30° for practical production of NTS.

3D chip stacks↗
DOE OSTI2020

Molecular-Scale Considerations of Enhanced Oil Recovery in Shale

With only less than 10% recovery, the primary production of hydrocarbon from shale reservoirs has redefined the energy equation in the world. Similar to conventional reservoirs, Enhanced Oil Recovery (EOR) techniques could be devised to enhance the current recovery factors. However, shale reservoirs possess unique characteristics that significantly affect the fluid properties. Therefore, we are adopting a molecular simulation approach that is well-suited to account for these effects to evaluate the performance of three different gases, methane, carbon dioxide and nitrogen, to recover the hydrocarbons from rough pore surfaces. Our hydrocarbon systems consists of either a single component (decane) or more than one component (decane and pentane). We simulated cases where concurrent and countercurrent displacement is studied. For concurrent displacement (injected fluids displace hydrocarbons towards the production region), we found that nitrogen and methane yielded similar recovery; however nitrogen exhibited a faster breakthrough. On the other hand, carbon dioxide was more effective in extracting the hydrocarbons when sufficient pressure was maintained. For countercurrent displacement (gases are injected and hydrocarbons are produced from the same direction), methane was found to be more effective, followed by carbon dioxide and nitrogen. In all cases, confinement reduced the recovery factor of all gases. This work provides insights to devise strategies to improve the current recovery factors observed in shale reservoirs.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2020

Two-Phase Fluid Flow Properties of Rough Fractures With Heterogeneous Wettability: Analysis With Lattice Boltzmann Simulations

Fractures are conduits for fluid flow in low-permeability geological formations. Multiphase flow properties of fractures are important in natural processes and in engineering applications such as the evaluation of the sealing capacity of caprocks and productivity of hydrocarbon-bearing tight rocks. Investigations of flow and transport through fractures typically focus on the effects of fracture geometric and mechanical factors such as aperture, roughness, and compressibility. The wettability of the fracture surfaces and its influence on microscale interfacial phenomena and macroscale effective transport properties are seldom studied. In this study, we investigated the effect of heterogeneous wetting properties on the displacement of water by supercritical CO2 through a series of lattice Boltzmann method simulations. The results show the evolution of the CO2 plume within a fracture is controlled by both the roughness of the aperture field and the wetting distribution. We combined these factors into a capillary pressure map that can be related to the macroscopic flow behavior of the fracture. We observed that heterogeneous wetting distributions promote the residual trapping of water where lower capillary pressures allowed for isolated water pockets in higher capillary pressure zones. Analysis of fracture unsteady relative permeability shows the effect of wetting on permeability evolution and provides support for the viscous-coupling relative permeability model. Finally, analysis of the steady-state relative permeability and saturation demonstrates a strong correlation between permeability and the standard deviation of the capillary pressure field. Thus, characterizing the distribution of wetting properties of fractures is crucial to understanding multiphase fracture flow and transport properties.

58 GEOSCIENCES↗
DOE OSTI2020

Reduced methane recovery at high pressure due to methane trapping in shale nanopores

By 2050, shale gas production is expected to exceed three-quarters of total US natural gas production. However, current unconventional hydrocarbon gas recovery rates are only around 20%. Maximizing production of this natural resource thus necessitates improved understanding of the fundamental mechanisms underlying hydrocarbon retention within the nanoporous shale matrix. In this study, we integrated molecular simulation with high-pressure small-angle neutron scattering (SANS), an experimental technique uniquely capable of characterizing methane behavior in situ within shale nanopores at elevated pressures. Samples were created using Marcellus shale, a gas-generative formation comprising the largest natural gas field in the United States. Our results demonstrate that, contrary to the conventional wisdom that elevated drawdown pressure increases methane recovery, a higher peak pressure led to the trapping of dense, liquid-like methane in sub-2 nm radius nanopores, which comprise more than 90% of the measured nanopore volume, due to irreversible deformation of the kerogen matrix. These findings have critical implications for pressure management strategies to maximize hydrocarbon recovery, as well as broad implications for fluid behavior under confinement.

58 GEOSCIENCES↗
DOE OSTI2020

Modeling Nanoconfinement Effects Using Active Learning

Predicting the spatial configuration of gas in nanopores of is relevant in applications such as fluid flow forecasting and hydrocarbon reserves estimation. For example, shale reservoirs have suffered from computationally intractable multiscale problems, since fluid properties such as viscosity, density, and adsorption must be calculated by using expensive molecular dynamics (MD) simulations within each nanopore, whereas flow through these connected nanopores must be simulated at the micrometer scale. We utilize machine learning techniques to quickly and accurately model nanoscale confinement effects as an important step toward bridging the nano and micro scales. Our workflow is based on building and training physics-based deep-neural-networks models by learning from a database of MD calculations. The model accounts for the adsorption phenomenon by predicting the statistical distribution of gas inside nanopores. Because large databases of MD calculations are expensive to create, we investigate active learning (AL) as a data set construction strategy. In this workflow, new data are selected based on the model uncertainty via the query-by-committee approach. We show that our workflow obtains accurate models that generalize to real scanning electron microscopy geometries with 1/10th of the number of MD calculations required vs random data set generation. Our method enables the possibility of modeling nanoconfinement effects at the mesoscale, where complex connected sets of nanopores affect flow.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Improved pore network models to simulate single-phase flow in porous media by coupling with lattice Boltzmann method

In this paper, different pore network models to simulate single-phase flow in porous media are built and their accuracy is evaluated. In addition to the conventional pore network model (CPNM) which consists of regular pore bodies and throat bonds, three improved pore network models (IPNMs) are developed allowing to better describing the real pore and throat geometry. The first improved pore network model (IPNM1) replaces the regular throat bond with a throat bond showing the real throat cross section. The second improvement (IPNM2) uses a series of sub-throat bonds with varying cross sections to better describe the real throat geometry, which is firstly proposed in this paper. The third model (IPNM3) extracts the real pore-throat-pore geometry without simplification. The conductance of fluid flow through these more realistic throat bonds is calculated by the lattice Boltzmann method (LBM). The accuracy and computational efficiency of the different pore network models are evaluated taking the LBM simulation over the whole porous medium as reference solution. The global permeability and detailed pressure distributions in the pores for the different pore network models are validated. The results show that the accuracy of the pore network model increases from CPNM to IPNM3, but at the expense of increasing computational cost. This study suggests that IPNM3 can replace a whole-domain LBM simulation with similar accuracy but much lower computational cost. As a first-order approximation the newly proposed IPNM2 is suggested as good compromise between accuracy and computational cost.

42 ENGINEERING↗
DOE OSTI2020

Scaling of Imbibition Front Dynamics in Heterogeneous Porous Media

Here we report a quantitative study on the dynamics of countercurrent imbibition in fractured rock samples with the application of CO 2 geosequestration, as the rock matrix is saturated with CO 2 and brine exists in the adjacent microfracture. Direct pore-scale simulations of spontaneous and forced imbibition in a three-dimensional heterogeneous porous matrix enable us to capture the effect of microscopic properties on the imbibition dynamics as these pore-level descriptions are ignored in the existing coarse-grained models. We have established new scaling classes for the propagation of the center of mass of the imbibition front and fluid-fluid interface broadening. It has become evident that the wettability is a major factor which leads to anomalies in these scaling laws. While the governing capillarity under the water-wet condition induces fast roughening dynamics of the interface, the adverse effect of capillary pressure under the intermediate-wet condition leads to a damping effect on the imbibition front fluctuations.

58 GEOSCIENCES↗
DOE OSTI2020

Controlled 3D nanoparticle deposition by drying of colloidal suspension in designed thin micro-porous architectures

Nanoparticle deposition by drying of colloidal suspension in thin micro-porous architectures has attracted a lot of attention in scientific research as well as industrial applications. However, the underlying mechanisms of such three-dimensional (3D) deposition are not yet fully revealed due to the complexity of the co-occurring processes of two-phase fluid flows, phase change and mass transport. Consequently, the control of 3D nanoparticle deposition remains a challenge. We use a combined experimental and numerical approach to achieve controlled 3D nanoparticle deposition by drying of colloidal suspension in two pillar-based thin micro-porous architectures. By the design of pillar layout, rectangular-spiral and circular-spiral deposition configurations are obtained globally. By varying the surface wettability, vertically symmetric and sloped nanoparticle depositions can be achieved locally. While the numerical modeling reveals the mechanisms of liquid internal flow, as well as the impact of local drying rate on nanoparticle transport, accumulation and final deposition, the experimental results of deposition configurations validate the controlling strategies. This combined experimental and numerical work provides a framework to achieve desired 3D nanoparticle deposition in thin micro-porous architectures, with a thorough understanding of the underlying mechanisms of two-phase fluid flows, phase change and mass transport.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modelling uranium dioxide corrosion under repository conditions: A pore-scale study of the chemical and thermal processes

This paper investigates the corrosion behaviors of spent uranium dioxide (UO 2 ) fuel when placed in geological repositories. We performed pore-scale reactive transport simulations of the UO 2 corrosion process in a defective fuel rod with different orientations of breach or fracture on its clad. It is found that the corrosion rate has strong dependency on the breach orientation. The highest corrosion rate of UO 2 is calculated when the angle between the groundwater flow direction and the clad fracture reaches 180°. UO 2 corrosion simulations with different flow rates are compared. The results show the higher flow rate accelerates the corrosion of UO 2 fuel. The effect of pH on the corrosion process is also determined. It is indicated that higher pH can limit the corrosion of UO 2 by reducing the reaction rate. The dependence of reaction rate and time on reactive surface area is explored. Spent fuel with lower surface area demonstrates longer lifetime under corrosion conditions. A numerical model coupling thermal conduction and chemical reactions is developed to assess the impact of temperature on the process of UO 2 corrosion. The results show that higher temperature leads to larger corrosion rates for UO 2 . Here, the predicted reaction rates are higher in comparison with the isothermal results. Hence, our results can help improve the fundamental understanding of UO 2 corrosion in geological repositories for long-term storage of spent nuclear fuels and provide guidance for the safe operations and selection of appropriate repositories.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗