Engineering topics

Juntao Xiong

Publications and source records attributed to Juntao Xiong.

At least 19 records

NASA NTRS2021

Anti-Phase Vortex Reduction Control for Rotor Noise Suppression

An investigation is conducted in 2019 under the NASA Ames Center Innovation Funds (CIF) project entitled “Anti-Phase Vortex Reduction Control for Rotor Noise Suppression“ to experimentally validate an anti-phase rotor noise suppression concept. The first objective of the investigation is to conduct computational fluid dynamics (CFD) simulations to investigate the noise characteristics of several anti-phase rotor designs. The second objective is to conduct a series of acoustic tests of anti-phase rotors in an anechoic chamber at Pennsylvania State University (PSU) to evaluate the merit of the anti-phase rotor concept. The CFD investigation seeks to optimize the anti-phase alternating trailing edge patterns for rotor noise suppression. The design objective is to maximize the noise reduction while maintaining the aerodynamic thrust. The investigation is performed using a three-dimensional (3D) Unsteady Reynolds-Averaged Navier-Stokes (URANS) commercial solver STAR-CCM+ together with the Ffowcs-Williams and Hawkings (FW-H) formula to obtain the aerodynamic thrust and far-field noise level. An acoustic study is conducted for 13 anti-phase design candidates based on a proprietary rotor design. The CAD geometry of the rotor is furnished by PSU. These design candidates include different alternating trailing edge (TE) waveforms, TE segment lengths, TE deflection amplitudes, and transition characteristics. The best design candidate among those explored is an anti-phase rotor that has a four-period TE waveform which results in a reduction in far-field noise level of 2.1 dB in the hover condition and a reduction of 1.1 dB in the forward flight condition at 9.7 m/s. A further acoustic study is conducted for a different rotor manufactured by APC. Five APC rotor design candidates are simulated. The best anti-phase design candidate for the APC rotor results in a reduction in far-field noise level of 4.0 dB in the hover condition. An in-phase design candidate is also studied. This in-phase design provides a noise reduction of 2.5 dB. A series of acoustic experiments in the PSU anechoic chamber have been conducted in July 2019 and October 2019. Both anti-phase and in-phase rotors fabricated for the left-hand and right-hand rotations are tested. In the hover condition, all the rotors do not provide sufficient evidence of improved acoustic performance. However, the experimental data in the hover condition are deemed to be inconclusive due to the flow recirculation in the anechoic chamber caused by the rotor downwash. In the forward flight condition at 9.7 m/s, the anti-phase right-hand rotor produces a noise reduction by as much as 6.5 dB in the frequency range of 2000-4000 Hz, while the in-phase right-hand rotor produces a noise reduction by as much as 5 dB in the same frequency range. Both the anti-phase and in-phase left hand rotors offer no evidence of noise reduction. The difference in the acoustic performance of the left-hand and right-hand rotors could be explained by the location of the microphone array which is placed to the left side of the rotors. This microphone array location could create a bias in the sound pressure level in favor of the right-hand rotor. Using the average noise reduction values, the anti-phase 4H rotor could offer a noise reduction by as much as 3.25 dB while the in-phase 4I rotor could produce up to a 2.5 dB noise reduction. Both the computational and experimental results have provided sufficient evidence to support the noise suppression capability of the proposed anti-phase rotor concepts.

Rotor noise↗

NASA NTRSDate not supplied

Flutter Analysis of the Transonic Truss-Braced Wing Aircraft Using Transonic Correction

This paper describes a flutter analysis method for the Transonic Truss-Braced Wing aircraft using a vortex lattice method coupled to an unsteady transonic correction method to account for unsteady aerodynamics in transonic flow. A steady-state vortex-lattice model of the Truss-Braced Wing aircraft is developed using vortex lattice code VSPAERO. A transonic and viscous flow correction method is implemented in the VSPAERO model to account for steady-state transonic and viscous flow effects using transonic small disturbance code TSFOIL coupled to an in-house integral boundary layer code. In addition, a wing-strut interference correction method is developed to account for the transonic interference aerodynamics in the strut juncture region using high-fidelity CFD code FUN3D. A structural dynamic finite-element model of the Truss-Braced Wing aircraft is developed using BEAM3D in-house finite-element code and is coupled to the VSPAERO. The BEAM3D model includes a geometric nonlinearity due to the tension in the strut which causes a deflection-dependent nonlinear stiffness. An unsteady transonic correction method is developed to better capture the unsteady aerodynamics in transonic flow. The unsteady transonic correction method makes use of the Theodorsen’s theory to account for the amplitude and phase shift of the unsteady lift coefficient in transonic flow. A preliminary flutter analysis of the Truss-Braced Wing aircraft is conduct to illustrate the unsteady transonic correction approach.

Nhan Nguyen↗

NASA NTRSDate not supplied

Study of Mach 0.8 Transonic Truss-Braced Wing Aircraft Wing-Strut Interference Effects

This paper presents computational study of transonic wing-strut interference effects of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft using the high-fidelity CFD solver FUN3D. The study is conducted for the wing-strut and the wing-alone configurations at design Mach number0.8 and Reynolds number14.0 ́106.The interference effects are calculated by comparing the wing aerodynamics along the spanwise direction between the wing-strut and the wing-alone configurations. The presence of the strut underneath the wing induces a suction peak on the lower surface of the wing, which causes changes in aerodynamic forces and moments. The interference effects of the Mach 0.8 TTBW aircraft are compared with the Mach 0.745 TTBW aircraft. A transonic wing-strut interference aerodynamic correction model is developed for use in a lower-fidelity tool, VSPAERO, for rapid aerodynamic analysis of the Mach 0.8 TTBW aircraft.

TTBW↗

NASA NTRSDate not supplied

Aerodynamic Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft with Variable-Camber Continuous Trailing-Edge Flap

This paper presents an aerodynamic optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft with Variable-Camber Continuous Trailing-Edge Flap (VC-CTEF). The VCCTEF is a novel wing shaping control concept to improve aircraft aerodynamic efficiency. Drag reduction studies are conducted for three different VCCTEF configurations with 6-, 10-, and 21-spanwise sections, respectively. A simple VCCTEF actuator weight model is proposed to account the weight penalty of the actuator in the design. A vortex-lattice model of the TTBW model is developed with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections for rapid aerodynamic performance evaluations. The VSPAERO model has been validated against wind tunnel test data. The optimization results show that the 21-spanwise sections VCCTEF has largest absolute drag coefficient reduction, however, the 6-spanwise sections VCCTEF provides a relatively better solution for drag reduction when the actuator weight penalty is considered. A high-fidelity CFD solver FUN3D is used to validate the VCCTEF optimization.

Aerodynamic Optimization↗

NASA NTRSDate not supplied

Multi-point Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a multi-point jig twist optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic small disturbance /integral boundary layer correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. The VSPAERO model has been validated against wind tunnel test data and FUN3D CFD simulation data. Three different flight conditions corresponding to Mach 0.745 at 40,000 ft are selected for the TTBW aircraft jig twist optimization to reduce the drag coefficients at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized jig twist achieves a drag reduction of about 9 counts, 7 counts, and8 counts corresponding to the lift coefficients 0.68, 0.73, and 0.78, respectively. A high-fidelity CFD solver FUN3D is used to validate the jig twist optimization.

Multi-point↗

NASA NTRSDate not supplied

Transonic Correction to Theodorsen's Theory for Oscillating Airfoil in Pitch and Plunge Toward Flutter

This paper presents a transonic correction method for an oscillating airfoil in pitch and plunge. The proposed method applies correction functions to the Theodorsen’s theory to capture the transonic nonlinear aero- dynamics. These correction functions apply necessary corrections to the amplitudes and the phase angles of the unsteady lift and pitching moment coefficients to account for transonic aerodynamics. The proposed method also postulates a correction for the motion of the aerodynamic center which could be induced by moving shocks. A series of unsteady RANS CFD simulations of the airfoil at the mean aerodynamic chord of the Transonic Truss-Braced Wing aircraft are conducted using FUN3D to provide data to construct these transonic correction functions. The computed responses of the unsteady lift and pitching moment coefficients using these transonic correction functions match the CFD simulation results very well even when the pitching moment coefficient is highly nonlinear. A flutter analysis of an airfoil in pitch and plunge illustrates the potential use of the proposed transonic correction method.

Transonic Flutter↗

NASA NTRSDate not supplied

Real-Time Drag Optimization of Aspect Ratio 13.5 Common Research Model with Distributed Flap System

This paper presents a real-time drag optimization study of the aspect ratio 13.5 Common Research Model (CRM) with a distributed mini-plain flap system. A surrogate aerodynamic model of the aspect ratio 13.5 CRM is developed based on an aerodynamic database computed by a transonic panel method to capture the aerodynamic coefficients as functions of the angle of attack, flap deflections, and Mach number. A recursive least-squares parameter estimation algorithm is designed to estimate the aerodynamic parameters of the surrogate model. The estimated surrogate model is then used in an on-line drag optimization strategy based on an adjoint method. The results of the real-time drag optimization indicate a drag reduction of 2.46% for Mach 0.80, 3.37% for Mach 0.85, and 1.95% for Mach 0.88. The results show the convergence of all parameter estimates.

Drag Optimization↗

NASA NTRSDate not supplied

Transonic Correction Method for Flight Dynamic Stability Analysis of Mach 0.745 Transonic Truss-Braced Wing

This paper presents a transonic correction method for obtaining dynamic stability derivatives for flight dynamic stability analysis. The method provides a transonic correction to the Theodorsen's theory of unsteady aerodynamics using FUN3D CFD solver of unsteady Reynolds-averaged Navier-Stokes equations (RANS) for a series of wing sections of the Mach 0.745 Transonic Truss-Braced Wing in pitch and plunge oscillations. Unsteady lift and pitching moment coefficients are obtained and used to develop the correction terms in the Theodorsen's theory to account for transonic aerodynamics. The unsteady lift and pitching moment derivatives with respect to the unsteady angle of attack are obtained as frequency response functions of the reduced frequency. These frequency response functions are used to compute the dynamic stability derivatives of lift and pitching moment due to the angle of attack and pitch rate and the dynamic stability derivatives for the rolling moment and yawing moment with respect to the roll rate and yaw rate. A transonic correction is applied to steady-state stability derivatives computed by VSPAERO solver using transonic small disturbance code TSFOIL coupled to an integral boundary method. A dynamic stability analysis is conducted for longitudinal and lateral-directional motions. Without transonic corrections and dynamic stability derivatives, the analysis indicates an unstable phugoid mode. The transonic correction applied to the steady-state stability derivatives computed by VSPAERO shows a stable phugoid mode. This is due to the increase of the drag stability derivatives as a result of the additional wave drag contribution in transonic flow. The effect of the transonic dynamic stability derivatives is observed to be a significant contributor to the increase in the damping values of all the flight dynamic modes of the Mach 0.745 Transonic-Truss Braced Wing.

Transonic↗

NASA NTRSDate not supplied

Fuel-Optimal Trajectory Optimization of Mach 0.745 Transonic Truss-Braced Wing with Variable Camber Continuous Trailing Edge Flap

This paper describes a fuel-optimal trajectory optimization of the Mach 0.745 Transonic Truss-Braced Wing with the variable camber continuous trailing edge flaps (VCCTEF) capable of changing the chordwise pressure distribution and spanwise lift distribution to minimize drag. The trajectory optimization is posed as a minimization of the fuel burn over a fixed cruise range. The trajectory optimization is formulated by the adjoint method which results in a two-point boundary value problem. A numerical shooting method is implemented to solve the minimum-fuel trajectory optimization. The results indicates a fuel burn reduction of 793 lbs or 5.5% for a cruise range of 3000 miles. An approximate trajectory optimization is proposed using a single adjoint variable. This leads to a greatly simplified analytical solution of the adjoint solution. The results of the approximate trajectory optimization are in excellent agreement with those obtained by the shooting method. The approximate trajectory optimization produces a fuel burn reduction of 615 lbs or 4.3%.

Trajectory Optimization↗

NASA NTRSDate not supplied

Aeroelastic Trim Drag Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft with Variable-Camber Continuous Trailing-Edge Flap

This paper presents an aeroelastic trim drag optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft with the Variable-Camber Continuous Trailing-Edge Flap (VCCTEF). An aero-structural analysis solver VSPAERO with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections coupled to finite-element code BEAM3D is developed to provide a rapid aircraft aeroelastic performance evaluation. The VSPAERO model has been validated against wind tunnel test data. Aeroelastic trim drag optimization studies are conducted for a VCCTEF configuration with 6-spanwise sections. Three different flight conditions corresponding to Mach 0.745 are selected for the TTBW aircraft aeroelastic trim drag optimization at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized VCCTEF deflection achieves a drag reduction of about 9.1 counts, 5.9 counts, and 11.8 counts corresponding to the lift coefficients 0.68, 0.73, and 0.78, respectively. A high-fidelity CFD solver FUN3D is used to validate the aeroelastic trim drag optimization.

Aeroelastic trim drag↗

NASA NTRSDate not supplied

Aeroelastic Modeling and CFD Simulation of Wind-Tunnel Scale Aspect Ratio 13.5 Common Research Model

This paper presents an aeroelastic modeling and simulation study of an aspect ratio 13.5 wind-tunnel scale Common Research Model (CRM) with distributed flaps. A vortex-lattice VSPAERO model of the CRM model is developed. A transonic small disturbance/integral boundary layer correction method is implemented in the VSPAERO model to account for the transonic and viscous flow effects. The structural deformation of the CRM model is calculated using a NASTRAN equivalent beam model. The VSPAERO model is coupled to the NASTRAN equivalent beam model to provide a rapid aero-structural analysis. A validation of the VSPAERO aeroelastic model is conducted by comparing the results to FUN3D CFD aeroelastic simulation results. An aerodynamic database is generated using the developed VSPAERO aeroelastic model for the real-time drag optimization and maneuver load alleviation study of the wind-tunnel scale CRM model.

Aeroelastic Modeling↗

NASA NTRSDate not supplied

Dynamic Aeroelastic Flight Dynamic Modeling of Mach 0.745 Transonic Truss-Braced Wing

This paper presents a modeling approach for dynamic aeroelastic flight dynamic analysis of the Mach0.745 Transonic Truss-Braced Wing. The modeling approach is based on a transonic correction method to correct the Theodorsen’s theory for transonic flow. CFD unsteady Reynolds-averaged Navier-Stokes equations (RANS) simulations are conducted using FUN3D solver for a series of wing sections from the Mach 0.745Transonic Truss-Braced Wing in pitch and plunge oscillations. Unsteady lift and pitching moment coefficients are obtained and used to develop the correction terms in the Theodorsen’s theory to account for transonic aerodynamics. The unsteady lift and pitching moment derivatives with respect to the unsteady angle of attack are obtained as functions of the reduced frequency. These derivatives are used to compute the unsteady lift and pitching moment contributions by the angle of attack, pitch rate, and roll rate. They are then approximated using a frequency-domain regression to obtain the dynamic stability derivatives for the Mach 0.745 Transonic Truss-Braced Wing. The structural dynamic mode shapes of the Mach 0.745 TTBW are extracted from a NAS-TRAN finite-element model. These mode shapes are used to compute the generalized unsteady aerodynamic forces. The aerodynamic mass, damping, and stiffness and the aerodynamic lag states are constructed to couple the dynamic aeroelastic contribution to the flight dynamic model of the Mach 0.745 Transonic Truss-Braced Wing. The coupled dynamic aeroelastic flight dynamic equations of motion are formulated. The eigenvalues of the coupled system are computed. All the flight dynamic modes and structural dynamic modes are stable at Match 0.745. The effect of transonic aerodynamics generally causes all the dynamic modes to have lower damping values

Flight Dynamics↗

NASA NTRSDate not supplied

Aerodynamic Optimization of Mach 0.8 Transonic Truss-Braced Wing Aircraft using Variable Camber Continuous Trailing Edge Flap

This paper presents an aerodynamic optimization study of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft with Variable Camber Continuous Trailing Edge Flap (VC-CTEF). The VCCTEF is a novel wing shaping control concept to improve aircraft aerodynamic efficiency. Drag reduction studies are conducted for two different VCCTEF configurations with 6- and 10-spanwise sections, respectively. A simple VCCTEF actuator weight model is used to account the weight penalty of the actuator in the design for the Mach 0.8 TTBW aircraft. A vortex-lattice model of the Mach 0.8 TTBW aircraft is developed with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections for rapid aerodynamic performance evaluations. The VSPAERO model has been validated against the wind tunnel test data. The optimization results show that the 6-spanwise sections VCCTEF provides a relatively better solution for drag reduction when the actuator weight penalty is considered. A high-fidelity CFD solver FUN3D is used to verify the VCCTEF optimization design.

Aerodynamic optimization↗

NASA NTRSDate not supplied

Aeroelastic Analysis of Mach 0.8 Transonic Truss-Braced Wing Aircraft

This paper presents an aeroelastic analysis of the Mach 0.8 Transonic Truss-Braced Wing(TTBW) aircraft jig shape using an in-house developed tool based on VSPAERO. A vortex-lattice model of the Mach 0.8 TTBW model is developed, and a transonic and viscous flow correction method is implemented to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. The Galerkin method is used to calculate the geometry deformation under aerodynamic force. The aero-structural analysis solver VSPAERO coupled to the mode shapes computed by NASTRAN using the Galerkin method provides a rapid aircraft aero-structual analysis. A high-fidelity CFD solver FUN3D is used to verify the results. The aeroelastic simulation results show that the aeroelastic lift coefficient is reduced about0.05∼0.07, drag polar is not affected by aeroelasticity, and the pitching moment is reduced about 30% at Mach0.8 and altitude 40,000 ft.

TTBW Aeroelastic↗

NASA NTRSDate not supplied

Wake Vortex Interaction of Urban Air Mobility Aircraft

This paper presents a study of wake vortex interaction modeling for urban air mobility. Wake vortex modeling approaches for fixed-wing aircraft and rotorcraft are investigated. A wake age model is developed that accounts for the temporal and spatial dissipation of the wake-induced downwash. A wake vortex model is developed for rotorcraft that accounts for blade flapping motion and cyclic pitch control to reduce the lift asymmetry. This in turn results in an equal lift circulation strength on the advancing side and retreating side of the rotor. Two wake vortex interaction simulations are performed to illustrate the modeling approaches.

Wake Vortex↗

NASA NTRSDate not supplied

CFD-Based Frequency Domain Method for Dynamic Stability Derivative Estimation with Application to Transonic Truss-Braced Wing

This paper presents a dynamic stability estimation technique obtained from high-fidelity CFD simulations of the Mach 0.8 Transonic Truss-Braced Wing (TTBW). A series of unsteady RANS CFD simulations in FUN3D is performed on the TTBW in pitch and plunge oscillations at various reduced frequencies. The time-domain data are transformed into the frequency-domain data by Fourier series. Transfer functions of the dynamic stability derivatives are then estimated by a frequency-domain regression. The dynamic stability derivatives with respect to the angle of attack are determined by the regression of the unsteady aerodynamic coefficients for the plunge motion. The dynamic stability derivatives with respect to the pitch rate are deter-mined by the regression of the differential unsteady aerodynamic coefficients for the pitch motion upon the removal of the angle of attack contribution by the plunge motion. The steady-state stability derivatives are then compared to the results obtained from a stability analysis code VSPAERO as well as steady-state FUN3D simulations. The comparison of the steady-state stability derivatives shows excellent agreement.

Dynamic Stability Derivatives↗

NASA NTRSDate not supplied

Aeroservoelastic Flight Dynamic Modeling of UAM Conceptual Vehicles

This paper presents an aeroservoelastic flight dynamic modeling approach for NASA Lift+Cruise eVTOL aircraft in forward flight. A conceptual aerodynamic analysis for forward flight is performed in CHARM, a rotorcraft aeromechanics unsteady vortex-lattice flow solver. A trim analysis is performed to obtain the steady state aerodynamic information at a trim point to be used for the aeroelastic analysis. A NASTRAN finite element model for the Lift+Cruise vehicle is available. The structural dynamic mode shapes are extracted from the NASTRAN for the aeroelastic analysis. An aeroservoelastic model is developed using the Theodorsen’s theory. A stability and control derivative analysis is performed to formulate a flight dynamic model of the Lift+Cruise vehicle. An aeroservoelastic flight dynamic model is formulated by coupling these two models together. Flight dynamic and flutter analyses are performed to determine vehicle stability and flutter-free operation.

Aeroservoelasticity↗

NASA NTRSDate not supplied

Aeroelastic Trim Drag Optimization of Mach 0.8 TransonicTruss-Braced Wing Aircraft with Variable Camber ContinuousTrailing Edge Flap

This paper presents an aeroelastic trim drag optimization study of the Mach 0.8 Tran-sonic Truss-Braced Wing (TTBW) aircraft with the Variable Camber Continuous TrailingEdge Flap (VCCTEF). An aero-structural analysis solver VSPAERO with transonic small dis-turbance, integral boundary-layer, and wing-strut interference corrections coupled to modeshapes computed by NASTRAN using the Galerkin method is developed to provide a rapidaircraft aeroelastic performance evaluation. Aeroelastic trim drag optimization studies areconducted for a VCCTEF configuration with 6-spanwise sections. Three different flight condi-tions corresponding to Mach 0.8 are selected for the aeroelastic trim drag optimization at thedesign and off-design cruise lift coefficients. The preliminary optimization results show thatthe TTBW aircraft with the optimized VCCTEF deflection achieves a drag reduction of about 9.2 counts, 9.6 counts, and 12.3 counts corresponding to the lift coefficients 0.661, 0.695, and0.729, respectively. When accounting for the actuator weight penalty, the corresponding dragreductions are 1.77%, 1.82%, 2.41%. A high-fidelity CFD solver FUN3D is used to validatethe aeroelastic trim drag optimization.

Aeroelastic trim drag↗