Engineering topics
Publications and source records attributed to Jones, M. H..
Deflectometer uses ASTM Standard Test E-399 clip-in displacement gage as sensing element. Gage is available in most fracture-testing laboratories and has good sensitivity and accuracy.
A description is presented of studies which have been conducted to establish an improved technology base for a use of the sharply notched cylindrical specimen in quality assurance tests of aluminum alloy products. The results are presented of an investigation of fundamental variables associated with specimen preparation and testing, taking into account the influence of the notch root radius, the eccentricity of loading, the specimen diameter, and the notch depth on the sharp notch strength. Attention is given to the statistical procedures which are necessary to establish correlations between the sharp notch strength and the plane-strain fracture toughness for high-strength aluminum alloys.
The reported investigation was undertaken in connection with an attempt to develop procedures which would be useful in standardizing a test method for the precracked Charpy slow bend specimen. A number of alloys was studied for which valid plane-strain fracture toughness values have been established. The investigation shows that useful relations between precracked Charpy slow bend results and crack size factors can be obtained under some circumstances. However, it is not yet known what factors control these circumstances.
Alignment results are presented in terms of percent bending for a quick release, tapered grip, tensile loading device that has been proposed for testing sharply notched specimens of aluminum and magnesium alloys by a Task Group of the ASTM Committee E-24 on Fracture Testing of Metals. The results show that the bending introduced by the fixtures is strongly dependent on their relative rotational positions in respect to the loading rods which adapt them, to the tensile machine. For one set of tapered grips the highest bending was about 15%. Recommendations are made for improvement in the design of the tapered grips which should reduce the bending stresses substantially.
Description of two axial alignment fixtures that are capable of providing very low load application eccentricity in tension tests of threaded notched cylindrical specimens. The described fixtures are simple in design, very compact, and free from the effects of friction. Also, an evaluation procedure is presented that can be used to qualify any fixture for use in sharp notch tensile tests.
Fracture toughness tests at room temperature were made on three-point loaded beryllium bend specimens cut from hot pressed block and a forged disk. These specimens had plane proportions conforming to ASTM E 399 and covered a thickness range of from 1/32 to 1/2 in. Two sets of bend specimens were tested, one having fatigue cracks and the other 0.5 mil radius notches. One objective of the investigation was the development of techniques to produce fatigue cracks in accordance with the procedures specified in ASTM E 399. This objective was achieved for the hot pressed material. In plane cracks were not consistently produced in the specimens cut from forged stock.
The uses of compliance measurements in linear fracture mechanics are discussed as a technique for determining the crack-extension force vs load, specimen dimensions, and elastic constants. Some practical examples of application are given, including specimen and transducer descriptions, experimental procedure, instrumentation, calculations, measurement precautions, friction effects, and data reduction. The limitations and advantages of compliance measurements are discussed. It is pointed out that good results can be obtained by the compliance method when its measurement precision is not lower than that required for Young's modulus.
A description of the computer program used for heating rate calculation for blunt bodies in hypersonic flow is given. The main program and each subprogram are described by defining the pertinent symbols involved and presenting a detailed flow diagram and complete computer program listing. Input and output parameters are discussed in detail. Listings are given for the computation of heating rates on (1) a blunted 15 deg half-angle cone at 20 deg incidence and Mach 10.6, (2) a blunted 70 deg slab delta wing at 10 deg incidence and Mach 8, and (3) the HL-10 lifting body at 20 deg incidence and Mach 10. In addition, the computer program output for two streamlines on the blunted 15 deg half-angle cone is listed. For Part 1, see N71-36186.
Beryllium fracture toughness test specimens were fatigue cracked using reversed cycling with a compression load two to three times the tension load. In worked beryllium, textures may be produced which result in fatigue cracks that are out of plane with the starter notch. Specimens of hot pressed stock exhibited load displacement records which were nonlinear throughout their course. Fracture specimens of both hot pressed and forged stock showed essentially no reduction of thickness and the fracture surfaces were flat and normal to the load axis. However, the stress intensity factor at maximum load increased with decreasing thickness. Load-displacement and electric potential records for the hot pressed beryllium specimens exhibited several anomalies such as negative residual crack mouth displacements and a decrease in electrical potential with increasing load.
Crack length and bend specimen thickness effects in plane strain fracture toughness tests of high strength steels
Crack length and thickness influence in plane strain fracture toughness tests
Clevis design for reduced friction errors associated with round hole clevis in plane strain fracture toughness measurements
Friction effects in round hole clevis for testing compact tension fracture toughness specimens
Comprehensive survey presents current methods of fracture toughness testing that are based on linear elastic fracture mechanics. General principles of the basic two dimensional crack stress field model are discussed in relation to real three dimensional specimens. Methods of test instrumentation and procedure are described.
Detection of initial cracking in sharply notched specimens by acoustic means, using phonograph pickup and tape recorder
Acoustic detection of crack initiation in sharply notched specimens of high strength alloys
Explore the source record for details and available documents.
Wing and fuselage sheet material for trisonic transports