Engineering topics

Johnston, James C.

Publications and source records attributed to Johnston, James C..

At least 19 records

NASA NTRS2018

Advanced Manifolds for Improved Solid Oxide Electrolyzer Performance

An investigation was conducted to see if additive manufacturing could be used to fabricate more efficient manifold designs for improved flow, reduced stresses, and decreased number of joints to be sealed for a solid oxide electrolyzer used to convert carbon dioxide to oxygen. Computational flow and mechanical modeling were conducted on a NASA Glenn Research Center patented cell and stack design with the potential to achieve a 3-4 times mass reduction. Various manifold designs were modeled, and two were downselected to be fabricated and tested. Some benefit was seen in a baffled manifold design, which directed incoming flow more effectively into the flow channels, compared to the original design, where the flow spent more time within the manifold itself. Flow measurements indicated some non-uniformity of flow across the channels at higher flow rates, which were not predicted by the model. Some possible explanations for the differences are discussed.

Linne, Diane L.↗

NASA NTRS2018

Comparison of Performance Test Results to CFD and Structural Models of Non-Contacting Finger Seals

Performance tests of non-contacting finger seal designs were conducted at 300, 700, 922 K (70, 800 and 1200 F) at pressure differentials up to 517 kPa (75 psid) and surface speeds up to 366 m/s (1200 ft/s). Room temperature, static analysis of the seal was performed. A simplified CFD model was developed to examine pressure loads within the seal. Results from the CFD model were used as input to a finite element analysis model of a six-finger segment of the non-contacting finger seal. Examination of predicted deflections of individual components of the seal gives insight into the seal behavior. Wear patterns from testing verify the pattern of radial deflection. The models are used to predict maximum pressure differential capability of the seal and compared to experimental results. The CFD model slightly under-predicts the measured leakage flow factor, but has the same trend as the measured flow factor versus pressure differential.

Seals:Brush Seals↗

NASA NTRS2014

Engineered Polymer Composites Through Electrospun Nanofiber Coating of Fiber Tows

Composite materials offer significant weight savings in many aerospace applications. The toughness of the interface of fibers crossing at different angles often determines failure of composite components. A method for toughening the interface in fabric and filament wound components using directly electrospun thermoplastic nanofiber on carbon fiber tow is presented. The method was first demonstrated with limited trials, and then was scaled up to a continuous lab scale process. Filament wound tubes were fabricated and tested using unmodified baseline towpreg material and nanofiber coated towpreg.

toughening↗

NASA NTRS2013

NextGen Operational Improvements: Will they Improve Human Performance

Modernization of the National Airspace System depends critically on the development of advanced technology, including cutting-edge automation, controller decision-support tools and integrated on-demand information. The Next Generation Air Transportation System national plan envisions air traffic control tower automation that proposes solutions for seven problems: 1) departure metering, 2) taxi routing, 3) taxi and runway scheduling, 4) departure runway assignments, 5) departure flow management, 6) integrated arrival and departure scheduling and 7) runway configuration management. Government, academia and industry are simultaneously pursuing the development of these tools. For each tool, the development process typically begins by assessing its potential benefits, and then progresses to designing preliminary versions of the tool, followed by testing the tool's strengths and weaknesses using computational modeling, human-in-the-loop simulation and/or field tests. We compiled the literature, evaluated the methodological rigor of the studies and served as referee for partisan conclusions that were sometimes overly optimistic. Here we provide the results of this review.

Beard, Bettina L.↗

NASA NTRS2013

Surface modified aerogel monoliths

This invention comprises reinforced aerogel monoliths such as silica aerogels having a polymer coating on its outer geometric surface boundary, and to the method of preparing said aerogel monoliths. The polymer coatings on the aerogel monoliths are derived from polymer precursors selected from the group consisting of isocyanates as a precursor, precursors of epoxies, and precursors of polyimides. The coated aerogel monoliths can be modified further by encapsulating the aerogel with the polymer precursor reinforced with fibers such as carbon or glass fibers to obtain mechanically reinforced composite encapsulated aerogel monoliths.

Leventis, Nicholas↗

NASA NTRS2012

Highly porous and mechanically strong ceramic oxide aerogels

Structurally stable and mechanically strong ceramic oxide aerogels are provided. The aerogels are cross-linked via organic polymer chains that are attached to and extend from surface-bound functional groups provided or present over the internal surfaces of a mesoporous ceramic oxide particle network via appropriate chemical reactions. The functional groups can be hydroxyl groups, which are native to ceramic oxides, or they can be non-hydroxyl functional groups that can be decorated over the internal surfaces of the ceramic oxide network. Methods of preparing such mechanically strong ceramic oxide aerogels also are provided.

Leventis, Nicholas↗

NASA NTRS2011

The Design, Fabrication, and Testing of Composite Heat Exchange Coupons

Several heat exchanger (HX) test panels were designed, fabricated and tested at the NASA Glenn Research Center to explore the fabrication and performance of several designs for composite heat exchangers. The development of these light weight, high efficiency air-liquid test panels was attempted using polymer composites and carbon foam materials. The fundamental goal of this effort was to demonstrate the feasibility of the composite HX for various space exploration and thermal management applications including Orion CEV and Altair. The specific objectives of this work were to select optimum materials, designs, and to optimize fabrication procedures. After fabrication, the individual design concept prototypes were tested to determine their thermal performance and to guide the future development of full-size engineering development units (EDU). The overall test results suggested that the panel bonded with pre-cured composite laminates to KFOAM Grade L1 scored above the other designs in terms of ease of manufacture and performance.

Quade, Derek J.↗

NASA NTRS2011

Acoustic Absorption in Porous Materials

An understanding of both the areas of materials science and acoustics is necessary to successfully develop materials for acoustic absorption applications. This paper presents the basic knowledge and approaches for determining the acoustic performance of porous materials in a manner that will help materials researchers new to this area gain the understanding and skills necessary to make meaningful contributions to this field of study. Beginning with the basics and making as few assumptions as possible, this paper reviews relevant topics in the acoustic performance of porous materials, which are often used to make acoustic bulk absorbers, moving from the physics of sound wave interactions with porous materials to measurement techniques for flow resistivity, characteristic impedance, and wavenumber.

Kuczmarski, Maria A.↗

NASA NTRS2010

Highly porous and mechanically strong ceramic oxide aerogels

Leventis, Nicholas↗

NASA NTRS2009

Toward Online Measurement of Decision State

In traditional perceptual decision-making experiments, two pieces of data are collected on each trial: response time and accuracy. But how confident were participants and how did their decision state evolve over time? We asked participants to provide a continuous readout of their decision state by moving a cursor along a sliding scale between a 100% certain left response and a 100% certain right response. Subjects did not terminate the trials; rather, trials were timed out at random and subjects were scored based on the cursor position at that time. Higher rewards for correct responses and higher penalties for errors were associated with extreme responses so that the response with the highest expected value was that which accurately reflected the participant's odds of being correct. This procedure encourages participants to expose the time-course of their evolving decision state. Evidence on how well they can do this will be presented.

Lachter, Joel↗

NASA NTRS2009

Toward Online Measurement of Decision State

In traditional perceptual decision-making experiments, two pieces of data recollected on each trial: response time and accuracy. But how confident were participants and how did their decision state evolve over time? We asked participants to provide a continuous readout of their decision state by moving a cursor along a sliding scale between a 100% certain left response and a 100% certain right response. Subjects did not terminate the trials; rather, trials were timed out at random and subjects were scored based on the cursor position at the time. Higher rewards for correct responses and higher penalties for errors were associated with extreme responses so that the response with the highest ex[pected value was that which accurately reflected the participant's odds of being correct. This procedure encourages participants to expose the time-course of their evolving decision state. Evidence on how well they can do this will be presented.

Lachter, Joel↗

NASA NTRS2008

Improved Thermal Design of a Compression Mold

A compression tool used to make 1-in. (2.5-cm) diameter disks of high-temperature polymers was designed to be shorter and of larger diameter than conventional tools to reduce heat loss to the surrounding air, thus making more efficient use of applied heat. This system is less sensitive to the amount and quality of insulation than previous tools, provides more repeatable processing, and improves the quality of the samples produced. These improvements come without increasing the weight of the punch portion of the tool over that of a conventional version, an important quality when handling lower-viscosity resins. In use, the base and body of the tool are assembled, and the polymer to be processed is placed into the body of the tool. The punch is inserted, and the assembled tool is placed into the press. A temperature/ pressure profile appropriate to the nature of the polymer is applied. A series of computational and experimental runs were made using a conventional tool to validate the computational model. The new tool design was then modeled, and when the performance showed a marked improvement, the new tool was manufactured. A new series of experimental runs showed that the thermal performance of the new tool agreed well with model predictions.

Kuczmarski, Maria A.↗

NASA NTRS2007

Strong, Lightweight, Porous Materials

A new class of strong, lightweight, porous materials has been invented as an outgrowth of an effort to develop reinforced silica aerogels. The new material, called X-Aerogel is less hygroscopic, but no less porous and of similar density to the corresponding unmodified aerogels. However, the property that sets X-Aerogels apart is their mechanical strength, which can be as much as two and a half orders of magnitude stronger that the unmodified aerogels. X-Aerogels are envisioned to be useful for making extremely lightweight, thermally insulating, structural components, but they may also have applications as electrical insulators, components of laminates, catalyst supports, templates for electrode materials, fuel-cell components, and filter membranes.

Leventis, Nicholas↗

NASA NTRS2007

Protective Skins for Aerogel Monoliths

A method of imparting relatively hard protective outer skins to aerogel monoliths has been developed. Even more than aerogel beads, aerogel monoliths are attractive as thermal-insulation materials, but the commercial utilization of aerogel monoliths in thermal-insulation panels has been inhibited by their fragility and the consequent difficulty of handling them. Therefore, there is a need to afford sufficient protection to aerogel monoliths to facilitate handling, without compromising the attractive bulk properties (low density, high porosity, low thermal conductivity, high surface area, and low permittivity) of aerogel materials. The present method was devised to satisfy this need. The essence of the present method is to coat an aerogel monolith with an outer polymeric skin, by painting or spraying. Apparently, the reason spraying and painting were not attempted until now is that it is well known in the aerogel industry that aerogels collapse in contact with liquids. In the present method, one prevents such collapse through the proper choice of coating liquid and process conditions: In particular, one uses a viscous polymer precursor liquid and (a) carefully controls the amount of liquid applied and/or (b) causes the liquid to become cured to the desired hard polymeric layer rapidly enough that there is not sufficient time for the liquid to percolate into the aerogel bulk. The method has been demonstrated by use of isocyanates, which, upon exposure to atmospheric moisture, become cured to polyurethane/polyurea-type coats. The method has also been demonstrated by use of commercial epoxy resins. The method could also be implemented by use of a variety of other resins, including polyimide precursors (for forming high-temperature-resistant protective skins) or perfluorinated monomers (for forming coats that impart hydrophobicity and some increase in strength).

Leventis, Nicholas↗

NASA NTRS2006

Manufacture of Regularly Shaped Sol-Gel Pellets

An extrusion batch process for manufacturing regularly shaped sol-gel pellets has been devised as an improved alternative to a spray process that yields irregularly shaped pellets. The aspect ratio of regularly shaped pellets can be controlled more easily, while regularly shaped pellets pack more efficiently. In the extrusion process, a wet gel is pushed out of a mold and chopped repetitively into short, cylindrical pieces as it emerges from the mold. The pieces are collected and can be either (1) dried at ambient pressure to xerogel, (2) solvent exchanged and dried under ambient pressure to ambigels, or (3) supercritically dried to aerogel. Advantageously, the extruded pellets can be dropped directly in a cross-linking bath, where they develop a conformal polymer coating around the skeletal framework of the wet gel via reaction with the cross linker. These pellets can be dried to mechanically robust X-Aerogel.

Leventis, Nicholas↗

NASA NTRS2003

Vanishing dual-task interference after practice: has the bottleneck been eliminated or is it merely latent?

Practice can, in some cases, largely eliminate measured dual-task interference. Does this absence of interference indicate the absence of a processing bottleneck (defined as an inability to carry out certain stages in parallel)? The authors show that a bottleneck need not produce any observable interference, provided that there is no temporal overlap in the demand for bottleneck stages on the 2 tasks. Such a "latent" bottleneck is especially likely after practice, when central stages are short. The authors provide new evidence that a latent bottleneck occurred for a participant who produced no interference in M. Van Selst, E. Ruthruff, and J. C. Johnston (1999). These findings demonstrate that the absence of dual-task interference does not necessarily indicate the absence of a processing bottleneck.

Clinical Trial↗

NASA NTRS2002

Repetition blindness has a perceptual locus: evidence from online processing of targets in RSVP streams

Four experiments tested whether repetition blindness (RB; reduced accuracy reporting repetitions of briefly displayed items) is a perceptual or a memory-recall phenomenon. RB was measured in rapid serial visual presentation (RSVP) streams, with the task altered to reduce memory demands. In Experiment 1 only the number of targets (1 vs. 2) was reported, eliminating the need to remember target identities. Experiment 2 segregated repeated and nonrepeated targets into separate blocks to reduce bias against repeated targets. Experiments 3 and 4 required immediate "online" buttonpress responses to targets as they occurred. All 4 experiments showed very strong RB. Furthermore, the online response data showed clearly that the 2nd of the repeated targets is the one missed. The present results show that in the RSVP paradigm, RB occurs online during initial stimulus encoding and decision making. The authors argue that RB is indeed a perceptual phenomenon.

Form Perception↗

NASA NTRS2002

Dual-Task Interference When A Response is Not Required

When subjects are required to respond to two stimuli presented in rapid succession, responses to the second stimulus are delayed. Such dual-task interference has been attributed to a fundamental processing bottleneck preventing simultaneous processing on both tasks. Two experiments show dual-task interference even when the first task does not require a response. The observed interference is caused by a bottleneck in central cognitive processing, rather than in response initiation or execution.

VanSelst, Mark↗