Engineering Papers⌕ Search

Engineering topics

Johnson, K. G.

Publications and source records attributed to Johnson, K. G..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Effects of model error on control of large flexible space antenna with comparisons of decoupled and linear quadratic regulator control procedures

An analysis was performed to determine the effects of model error on the control of a large flexible space antenna. Control was achieved by employing two three-axis control-moment gyros (CMG's) located on the antenna column. State variables were estimated by including an observer in the control loop that used attitude and attitude-rate sensors on the column. Errors were assumed to exist in the individual model parameters: modal frequency, modal damping, mode slope (control-influence coefficients), and moment of inertia. Their effects on control-system performance were analyzed either for (1) nulling initial disturbances in the rigid-body modes, or (2) nulling initial disturbances in the first three flexible modes. The study includes the effects on stability, time to null, and control requirements (defined as maximum torque and total momentum), as well as on the accuracy of obtaining initial estimates of the disturbances. The effects on the transients of the undisturbed modes are also included. The results, which are compared for decoupled and linear quadratic regulator (LQR) control procedures, are shown in tabular form, parametric plots, and as sample time histories of modal-amplitude and control responses. Results of the analysis showed that the effects of model errors on the control-system performance were generally comparable for both control procedures. The effect of mode-slope error was the most serious of all model errors.

Hamer, H. A.↗
NASA NTRS1985

Decoupled and linear quadratic regulator control of a large, flexible space antenna with an observer in the control loop

An analysis is performed to compare decoupled and linear quadratic regulator (LQR) procedures for the control of a large, flexible space antenna. Control objectives involve: (1) commanding changes in the rigid-body modes, (2) nulling initial disturbances in the rigid-body modes, or (3) nulling initial disturbances in the first three flexible modes. Control is achieved with two three-axis control-moment gyros located on the antenna column. Results are presented to illustrate various effects on control requirements for the two procedures. These effects include errors in the initial estimates of state variables, variations in the type, number, and location of sensors, and deletions of state-variable estimates for certain flexible modes after control activation. The advantages of incorporating a time lag in the control feedback are also illustrated. In addition, the effects of inoperative-control situations are analyzed with regard to control requirements and resultant modal responses. Comparisons are included which show the effects of perfect state feedback with no residual modes (ideal case). Time-history responses are presented to illustrate the various effects on the control procedures.

Hamer, H. A.↗
NASA NTRS1984

Decoupled control analysis of a large flexible space antenna with linear quadratic regulator comparisons

A decoupled-control analysis was performed for a large flexible space antenna. Control involved commanding changes in the rigid-body modes or nulling disturbances in the flexible modes. The study provides parametric-type data which could be useful in the final design of a large space antenna control system. Results are presented to illustrate the effect on control requirements of (1) the number of modes controlled; (2) the number, type, and location of control actuators; and (3) variations in the closed-loop dynamics of the control system. Comparisons are given between the decoupled-control results and those obtained by using a linear quadratic regulator approach. Time history responses are presented to illustrate the effects of the control procedures.

Young, J. W.↗
NASA NTRS1980

Pseudosteady-state analysis of nonlinear aircraft maneuvers

An analytical method was developed for studying the combined effects of rotational coupling and nonlinear aerodynamics on aircraft response for specified control inputs. The method involves the simultaneous solution of two nonlinear equations which are functions of angle attack, roll rate, and control inputs. The method was applied to a number of maneuvers for a fighter-type aircraft. Time history responses verified the usefulness of the analysis for predicting a variety of response characteristics caused by interacting nonlinear aerodynamic and inertial effects, including spin conditions.

Young, J. W.↗
NASA NTRS1980

Decoupled control of a long flexible beam in orbit

Control involved commanding changes in pitch attitude as well as nulling initial disturbances in the pitch and flexible modes. Control force requirements were analyzed. Also, the effects of parameter uncertainties on the decoupling process were analyzed and were found to be small. Two methods were investigated: the system was completely coupled and certain actuators were then eliminated, one by one, which resulted in some or all modes not fully controlled; specified modes of the system were excluded from the decoupling control law by employing viewer control actuators than modes in the model. In both methods, adjustments were made in the feedback gains to include the uncontrolled modes in the overall control of the system.

Hamer, H. A.↗
NASA NTRS1980

Pseudosteady state analysis of nonlinear aircraft maneuvers

An analytical method has been developed for studying the combined effects of rotational coupling and nonlinear aerodynamics on aircraft response for specified control inputs. The method involves the simultaneous solution of two nonlinear equations which are functions of angle of attack, roll rate, and the control inputs. The method is applied to a number of maneuvers for a fighter type aircraft. Time history responses verified the usefulness of the analysis for predicting a variety of response characteristics caused by interacting nonlinear aerodynamic and inertial effects, including spin conditions.

Young, J. W.↗
NASA NTRS1980

Pareto-optimal multi-objective design of airplane control systems

A constrained minimization algorithm for the computer aided design of airplane control systems to meet many requirements over a set of flight conditions is generalized using the concept of Pareto-optimization. The new algorithm yields solutions on the boundary of the achievable domain in objective space in a single run, whereas the older method required a sequence of runs to approximate such a limiting solution. However, Pareto-optimality does not guarantee a satisfactory design, since such solutions may emphasize some objectives at the expense of others. The designer must still interact with the program to obtain a well-balanced set of objectives. Using the example of a fighter lateral stability augmentation system (SAS) design over five flight conditions, several effective techniques are developed for obtaining well-balanced Pareto-optimal solutions. For comparison, one of these techniques is also used in a recently developed algorithm of Kreisselmeier and Steinhauser, which replaces the hard constraints with soft constraints, using a special penalty function. It is shown that comparable results can be obtained.

Schy, A. A.↗
NASA NTRS1979

A multiple objective optimization approach to aircraft control systems design

The design of an aircraft lateral control system, subject to several performance criteria and constraints, is considered. While in the previous studies of the same model a single criterion optimization, with other performance requirements expressed as constraints, has been pursued, the current approach involves a multiple criteria optimization. In particular, a Pareto optimal solution is sought.

Tabak, D.↗
NASA NTRS1978

Effects of errors on decoupled control systems

Various error sources in a decoupled control system are considered in connection with longitudinal control on a simulated externally blown jet-flap STOL aircraft. The system employed the throttle, horizontal tail, and flaps to decouple the forward velocity, pitch angle, and flight-path angle. The errors considered were: (1) imperfect knowledge of airplane aerodynamic and control characteristics; (2) imperfect measurements of airplane state variables; (3) change in flight conditions, and (4) lag in the airplane controls and in engine response. The effects of the various errors on the decoupling process were generally minor. Significant coupling in flight-path angle was caused by control lag during speed-command maneuvers. However, this coupling could be eliminated by including the control lag in the design of the decoupled system. Other error sources affected primarily the commanded response quantity.

Hamer, H. A.↗
NASA NTRS1977

Prediction of jump phenomena in rotationally-coupled maneuvers of aircraft, including nonlinear aerodynamic effects

An analytical method has been developed for predicting critical control inputs for which nonlinear rotational coupling may cause sudden jumps in aircraft response. The analysis includes the effect of aerodynamics which are nonlinear in angle of attack. The method involves the simultaneous solution of two polynomials in roll rate, whose coefficients are functions of angle of attack and the control inputs. Results obtained using this procedure are compared with calculated time histories to verify the validity of the method for predicting jump-like instabilities.

Young, J. W.↗
NASA NTRS1974

Computer-aided design of control systems to meet many requirements

A method is described for using nonlinear programing in the computer-aided design of airplane control systems. It is assumed that the quality of such systems depends on many criteria. These criteria are included in the constraints vector (instead of attempting to combine them into a single scalar criterion, as is usually done), and the design proceeds through a sequence of nonlinear programing solutions in which the designer varies the specification of sets of requirements levels. The method is applied to design of a lateral stability augmentation system (SAS) for a fighter airplane, in which the requirements vector is chosen from the official handling qualities specifications. Results are shown for several simple SAS configurations designed to obtain desirable handling qualities over all design flight conditions with minimum feedback gains. The choice of the final design for each case is not unique but depends on the designer's decision as to which achievable set of requirements levels represents the best for that system. Results indicate that it may be possible to design constant parameter SAS which can satisfy the most stringent handling qualities requirements for fighter airplanes in all flight conditions. The role of the designer as a decision maker, interacting with the computer program, is discussed. Advantages of this type of designer-computer interaction are emphasized. Desirable extensions of the method are indicated.

Schy, A. A.↗
NASA NTRS1972

Lunar rock splitter/can sealer

A manually powered and operated force generating device fractures lunar material as received from the moon and seals cans containing lunar samples. The rock splitting and can sealing operations are carried out in a vacuum environment. Can sealing is a cold welding process that requires a pressure of 125,000 psi (generating 32,000 lb for the largest can used). The design and modification of the device and the operating experience are described.

Johnson, K. G.↗
NASA NTRS1972

Simplified interplanetary guidance procedures using onboard optical measurements

Simplified guidance procedures have been developed which are based on preflight determination of the characteristics of perturbed trajectories. The results are devoted primarily to planetary approach guidance; however, some considerations for midcourse guidance are included. The methods are studied for an Earth-to-Mars trajectory but would be applicable to Grand Tour and other types of missions. Generally requiring only a single onboard optical angular measurement, the approach procedure predicts guidance corrections for the control of periapsis radius as well as orbital plane orientation. An error analysis has shown that the periapsis radius at Mars can be controlled to a 1 sigma accuracy of about 20 km if the guidance is performed 1/2 day before periapsis passage. If the guidance is performed at the Martian sphere of influence (2.2 days before periapsis), the error doubles because of the increased effect of measurement and maneuvering errors.

Hamer, H. A.↗
NASA NTRS1969

Precisely repeatable rotary mechanism

Precision-finished lead screw and a fitted mating nut member produce a linear translatory motion. This motion is transformed to a rotary movement of a pivotal platform member. The transformation is achieved by coupling the nut member and the platform member through a pair of opposed, taut, flex bands.

Johnson, K. G.↗