Engineering Papers⌕ Search

Engineering topics

Johnson, J. W.

Publications and source records attributed to Johnson, J. W..

27 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Dual frequency correlation radar measurements of the height statistics of ocean waves

A radar technique has been developed for measuring the statistical height properties of a random rough surface. This method is being applied to the problem of measuring the significant wave height and probability density function of ocean waves from an aircraft or spacecraft. Earlier theoretical and laboratory results have been extended to define the requirements and performance limitations of flight systems. Some details of the current airborne radar system are discussed and results obtained on several experimental missions are presented and interpreted.

Weissman, D. E.↗
NASA NTRS1976

Measurements of wave height statistics and radar, cross-section in a wind wave tank

There is currently wide interest among oceanographers and meteorologists in remote sensing of ocean surface characteristics. A wind wave tank developed at Langley Research Center is used to evaluate various remote sensing techniques based on electromagnetic scattering phenomena, and in the development and evaluation of theoretical scattering models. The wave tank is described, the statistics of the rough water surface are documented, and microwave radar cross-section measurement results are presented. The water surface statistics are similar in key respects to the open ocean, and the microwave scattering measurements show, qualitatively, theoretically predicted large and small scale scattering effects.

Johnson, J. W.↗
NASA NTRS1975

Dual frequency scatterometer measurement of ocean wave height

A technique for remotely measuring wave height averaged over an area of the sea surface was developed and verified with a series of aircraft flight experiments. The measurement concept involves the cross correlation of the amplitude fluctuations of two monochromatic reflected signals with variable frequency separation. The signal reflected by the randomly distributed specular points on the surface is observed in the backscatter direction at nadir incidence angle. The measured correlation coefficient is equal to the square of the magnitude of the characteristic function of the specular point height from which RMS wave height can be determined. The flight scatterometer operates at 13.9 GHz and 13.9 - delta f GHz with a maximum delta f of 40 MHz. Measurements were conducted for low and moderate sea states at altitudes of 2, 5, and 10 thousand feet. The experimental results agree with the predicted decorrelation with frequency separation and with off-nadir incidence angle.

Johnson, J. W.↗
NASA NTRS1975

Microwave scattering from the ocean surface

This paper is a review of current aircraft and satellite microwave remote sensing programs concerned with the measurement of ocean wave and surface wind conditions. These particular measurements have been identified by the user community as offering significant economic and technological benefits. Active microwave remote sensing techniques for these applications have been described theoretically and verified experimentally. The results of recent aircraft and satellite experimental programs are presented herein along with plans for the SeaSat-A Satellite Scatterometer.

Jones, W. L.↗
NASA NTRS1974

A dual frequency radar for ocean roughness sampling

A microwave technique for determining the roughness (rms wave height) of a randomly varying air-water interface has been developed theoretically, verified with laboratory wavetank studies and is currently being implemented for ocean surface measurements in a series of applications flight experiments. These aircraft observations will be near the Chesapeake Light Tower and will include a range of altitudes and sea conditions. The measurement concept involves cross-correlating the envelope fluctuations on two received carriers that are monochromatic when transmitted in a normal direction to the interface and are observed in a backscatter direction after reflection by the large number of randomly distributed specular points on the surface. The measured correlation coefficient (normalized covariance) as a function of carrier frequency separation will depend on the surface roughness, specifically the probability density function of the specular point height. Details of the flight system are discussed, and preliminary flight results are presented.

Weissman, D. E.↗
NASA NTRS1973

Proton-radiation damage in Gunn oscillators

The irradiation effects of 22 MeV protons on the electrical characteristics of GaAs continuous-wave Gunn oscillators was studied. The radio frequency power output was reduced by 3 decibels at proton fluences in the neighborhood of 1.5 x 10 to the 12th power protons/sq cm. Conductance measurements indicate that the carrier removal rate at high electric fields remained roughly 40 percent less than at low fields. Diode efficiencies of two device groups were found to be monotonically descreasing functions of fluence. Frequency modulation noise was generally unaffected by radiation, but the magnitude of the noise in the noise power spectrum increased significantly. These effects are partially accounted for, in a qualitative fashion, by a model of electron traps having field-dependent net-carrier capture rates and various response times.

Johnson, J. W.↗
NASA NTRS1973

Characterization of nickel-copper alloy specimens processed as a part of the M553 sphere forming experiment during the Skylab 1 and 2 flight

Both processed nickel-copper alloy specimens apparently completely melted by the electron beam in the Skylab M512 materials processing facility and either floated free in space, but collided with some smooth flat surface before solidifying, or remained attached to its support post during solidification. Both specimens had a smooth flat area on the surface due to this adherence during solidification. The nominal composition of the alloy before processing in space was 70 percent Ni and 30 percent Cu. Tests show that a considerable amount of copper was lost during processing by evaporation. It was further found that less copper was present in the cap areas, particularly at the surface, than was in the remainder of the specimens. The microchemistry of the dendrites and interdendritic regions, however, is in agreement with the phase diagram for this alloy. The measured densities of these specimens were less than the theoretical density of the alloy due to the amount of porosity present, however, no large voids were found by radiographic techniques.

Hubbard, J. L.↗
NASA NTRS1973

Characterizations of four specimens processed as a part of the M553 sphere forming experiment performed during the Skylab 1 and 2 flight

Four specimens identified as SL-1.3, SL-1.8, SL-1.9 and SL-2.5 were submitted for metallurgical characterization. These specimens had been processed in the M512 Facility as a part of the M553 Sphere Forming Experiment performed during the Skylab 1/2 flight. Three of these specimens, SL-1.3, SL-1.8, and SL-2.5 were designed to be melted completely by the electron beam and detach themselves from their support posts and resolidify while floating free in the near zero gravity and vacuum environment of space. Specimens SL-1.3 and SL-1.8 were completely melted, but it is believed they did not leave their posts before solidifying. Specimen SL-2.5 was only partially melted. Specimen SL-1.9 was to be completely melted and retained on a large sting which was accomplished as planned. The nominal composition of the four specimens was: (1) SL-1.3 - Ni 12% Sn; (2) SL-1.8 - Ni 30% Cu; (3) SL-1.9 - Pure Ni; and (4) SL-2.5 - Pure Ni. These four specimens have been examined according to the Phase B Characterization Plan. The results are discussed and compared with similar characterization analyses run on ground base specimens.

Hubbard, J. L.↗