Engineering Papers⌕ Search

Engineering topics

Jin, Ke

Publications and source records attributed to Jin, Ke.

At least 37 records · Page 2

Defect evolution in Ni and NiCoCr by in situ 2.8 MeV Au irradiation

The evolution of radiation-induced defects in Ni and the single-phase concentrated solid solution alloy, NiCoCr, were investigated during in situ 2.8 MeV Au ion irradiation and post-irradiation analysis using transmission electron microscopy. Compared to Ni, both the size and area density of defect clusters decreased in NiCoCr under the same irradiation conditions, suggesting that the chemical complexity, i.e., randomness of lattice site occupations, of NiCoCr suppressed radiation-induced damage. One-dimensional glide of defect clusters was observed in Ni but not in the NiCoCr alloy. The structural nature of small defect clusters in NiCoCr were further investigated using high-angle annular dark field scanning transmission electron microscopy.

36 MATERIALS SCIENCE↗

Temperature-dependent defect accumulation and evolution in Ni-irradiated NiFe concentrated solid-solution alloy

Temperature significantly affects defect migration and evolution in irradiated materials. However, the effects of temperature on defect evolution in concentrated solid-solution alloys (CSAs), including high entropy alloys, are not well understood, despite their potential as structural materials in advanced nuclear reactors. As an important model system of these CSAs, equiatomic Ni 50 Fe 50 (NiFe) was selected to understand the effects of temperature on defect evolution during irradiation and subsequent thermal annealing. Specifically, defect accumulation and evolution in NiFe alloy under Ni-ion irradiation at 150, 300, and 500 K were studied, and the irradiated specimens were subsequently annealed at higher temperatures. Rutherford backscattering spectrometry along the <100> channeling direction was employed to study damage accumulation and evolution before and after each irradiation and annealing experiment. Here we show that more defects survive and accumulate at 150 K, but more importantly defects can migrate to deeper depths at this low irradiation temperature. Irradiation-induced damage at 150 and 300 K does not recover substantially after post-irradiation annealing at 500 K, but dramatic recovery is observed after post-irradiation annealing at 700 K, indicating an onset temperature of defect recovery between 500 and 700 K. Here, the migration of irradiation-induced defects upon annealing is closely related to the mobility and stress state arising from the surviving defects. With the consideration of five stages of defect recovery in conventional dilute alloys, the underlying mechanisms for temperature-dependent defect accumulation and evolution in NiFe CSA are discussed.

36 MATERIALS SCIENCE↗

Channeling analysis in studying ion irradiation damage in materials containing various types of defects

We present that ion channeling is a powerful quantitative technique for studying ion-irradiation induced defect evolution in single crystalline materials. An iterative procedure to determine dechanneling yields has been developed for decades, serving as a major method for analyzing experimental channeling data. The applicability of such procedure is, however, generally limited to the crystalline damage with only point defects and local amorphous domains. For the other cases, such as irradiated metals, the assumption of direct-backscattering free has usually been made. In the present study, Ni, TiAl, MgO, and SrTiO 3 single crystals are selected as four model materials, representing metals, intermetallic alloys, and ceramic compounds with different defect evolution processes under irradiation, to investigate the fidelity of applying dechanneling analysis on various types of defects. The pure dechanneling assumption is shown oversimplified in Ni irradiated with low fluence self-ions and may result in error on the derived damage profile. Moreover, the iterative procedure of dechanneling analysis is shown valid for more general situations than the randomly distributed atoms, including those not exhibiting a peak in channeling spectra. The disappearance of damage peak in channeling spectra is attributed to the combined effects of small (but non-zero) scattering factor, long-range damage effects, and non-ignorable damage level in pristine crystals. Furthermore, the ratio of direct backscattering to dechanneling areas provides information on defect configurations in the materials containing a well-defined damage peak in channeling spectra. Finally, the contribution from dechanneling sources increases from SrTiO 3 , TiAl, to MgO, according to the derived scattering and dechanneling factors.

36 MATERIALS SCIENCE↗

Effects of Fe concentration on helium bubble formation in NiFe x single-phase concentrated solid solution alloys

The formation of helium bubbles and the consequential property degradation are critical challenges for materials used in advanced nuclear energy systems. The mechanism of helium bubble formation in a series of NiFe x (x = 0, 20, 35, or 50 at.%) single-phase concentrated solid solution alloys (SP-CSAs) are studied in this work. Transmission electron microscopy analysis shows that with increasing Fe concentration, the average bubble size decreases while the bubble number density increases, indicating the growth of large helium bubbles in NiFe x SP-CSAs is suppressed by increasing the alloy chemical complexity through increased Fe concentration. Mechanisms for the slower bubble growth rate in NiFe x binary SP-CSAs compared Ni are identified. These mechanisms include promotion of Frenkel pair recombination, denser and more homogeneously distributed nucleation sites, and increased helium atom densities inside the bubbles. Here, the results demonstrate that optimizing the chemical complexity in SP-CSAs can be an effective approach to design materials with superior resistance to helium bubble nucleation and growth.

36 MATERIALS SCIENCE↗

Lattice Distortion and Phase Stability of Pd-Doped NiCoFeCr Solid-Solution Alloys

In the present study, we have revealed that (NiCoFeCr)100−xPdx (x= 1, 3, 5, 20 atom%) high-entropy alloys (HEAs) have both local- and long-range lattice distortions by utilizing X-ray total scattering, X-ray diffraction, and extended X-ray absorption fine structure methods. The local lattice distortion determined by the lattice constant difference between the local and average structures was found to be proportional to the Pd content. A small amount of Pd-doping (1 atom%) yields long-range lattice distortion, which is demonstrated by a larger (200) lattice plane spacing than the expected value from an average structure, however, the degree of long-range lattice distortion is not sensitive to the Pd concentration. The structural stability of these distorted HEAs under high-pressure was also examined. The experimental results indicate that doping with a small amount of Pd significantly enhances the stability of the fcc phase by increasing the fcc-to-hcp transformation pressure from ~13.0 GPa in NiCoFeCr to 20–26 GPa in the Pd-doped HEAs and NiCoFeCrPd maintains its fcc lattice up to 74 GPa, the maximum pressure that the current experiments have reached.

36 MATERIALS SCIENCE↗

Helium irradiated cavity formation and defect energetics in Ni-based binary single-phase concentrated solid solution alloys

In this study, binary single-phase concentrated solid solution alloys (SPCSAs), including Ni 80 Co 20 , Ni 80 Fe 20 , Ni 80 Cr 20 , Ni 80 Pd 20 , and Ni 80 Mn 20 (in atomic percentage), were irradiated with 200 keV He + ions at 500 °C. He cavity size and density distribution were systematically investigated using transmission electron microscope. Here we show that alloying elements have a clear impact on He cavity formation. Cavity size is the smallest in Ni 80 Mn 20 but the largest in Ni 80 Co 20 . Alloying elements could also substantially affect cavity density profile. In-depth examination of cavities at peak damage region (~500 nm) and at low damage region (~300 nm) demonstrates that cavity size is depth (damage) dependent. Competition between consumption and production of vacancies and He atoms could lead to varied cavity size. Density functional theory (DFT) calculations were performed to obtain the formation and migration energies of interstitials and vacancies. Combined experimental and simulation results show that smaller energy gap between interstitial and vacancy migration energies may lead to smaller cavity size and narrower size distribution observed in Ni 80 Mn 20 , comparing with Ni 80 Co 20 . Finally, the results of this study call attention to alloying effects of specific element on cavity formation and defect energetics in SPCSAs, and could provide fundamental understanding to predict radiation effects in more complexed SPCSAs, such as high entropy alloys.

36 MATERIALS SCIENCE↗

Enhanced strength and ductility of a tungsten-doped CoCrNi medium-entropy alloy

Developing metallic materials with a good combination of strength and ductility has been an unending pursuit of materials scientists. The emergence of high/medium-entropy alloys (HEA/MEA) provided a novel strategy to achieve this. In this work, we also strengthened a strong-and-ductile MEA using a traditional solid solution strengthening theory. The selection of solute elements was assisted by mechanical property and microstructure predictive models. Extensive microstructural characterizations and mechanical tests were performed to verify the models and to understand the mechanical behavior and deformation mechanisms of the designated CoCrNi–3W alloy. Our results show good experiment-model agreement. The incorporation of 3 at.% W into the ternary CoCrNi matrix increased its intrinsic strength by ~20%. External strengthening through microstructural refinement led to a yield strength nearly double that of the parent alloy, CoCrNi. The increase in strength is obtained with still good ductility when tested down to 77 K. Nanoscale twin boundaries are observed in the post-fracture microstructure under 77 K. Finally, the combination of strength and ductility after W additions deviate from the traditional strength-ductility-trade-off contour.

36 MATERIALS SCIENCE↗

Interstitial migration behavior and defect evolution in ion irradiated pure nickel and Ni-xFe binary alloys

Transition from long-range one-dimensional to short-range three-dimensional migration modes of interstitial defect clusters greatly reduces the damage accumulation in single-phase concentrated solid solution alloys under ion irradiation. A synergetic investigation with experimental, computational and modeling approaches revealed that both the resistance to void swelling and the delay in dislocation evolution in Ni-Fe alloys increased with iron concentration. This was attributed to the gradually increased sluggishness of defect migration, which enhances interstitial and vacancy recombination. Transition from long-range one-dimensional defect motion in pure nickel to short-range three-dimensional motion in concentrated Ni-Fe alloys is continuum, not abrupt, and within an iron concentration range up to 20%. Lastly, the gradual transition process can be quantitatively characterized by the mean free path of the interstitial defect clusters.

36 MATERIALS SCIENCE↗

Influence of irradiation temperature on void swelling in NiCoFeCrMn and NiCoFeCrPd

Here, using ion irradiation and transmission electron microscopy, temperature dependent void swelling and dislocation loop evolution in equiatomic NiCoFeCrMn and NiCoFeCrPd high entropy alloys were investigated. Voids were observed in all tested conditions. An order higher of swelling was observed in both HEAs as temperature increased from 420 to 580 °C. Alloying with Pd was found to have a stronger suppression effect on void and dislocation loop growth than alloying with Mn. Possible contributions to the swelling resistance were explored, including localized lattice distortion and higher defect migration barrier in NiCoFeCrPd. Additionally, no phase decomposition was observed in either alloy.

36 MATERIALS SCIENCE↗

Enhanced void swelling in NiCoFeCrPd high-entropy alloy by indentation-induced dislocations

The role of dislocations on ion irradiation-induced void formation is studied in a high-entropy alloy (HEA) NiCoFeCrPd. Despite previous observations that show high-entropy alloys are swelling resistant due to a high defect recombination rate, the swelling is enhanced with increasing density of pre-existing dislocations at low strain levels that shortened transient duration before the onset of void swelling. Under certain irradiation conditions, a high density of dislocations may carry the material closer to the sink-dominated regime. Finally, compared to another HEA NiCoFeCrMn, NiCoFeCrPd has a smaller loop size and higher loop density due to the stronger lattice distortion.

36 MATERIALS SCIENCE↗

Quantifying early stage irradiation damage from nanoindentation pop-in tests

Early stage irradiation effects on incipient plasticity are quantitatively investigated in single-crystalline molybdenum using nanoindentation pop-in tests. Defects produced under low-dose ion irradiations, even when they are hardly detected by ion-channeling technique, can significantly reduce the critical stress for the elastic-plastic transition, through acting as heterogeneous dislocation nucleation sources. Here, the density and strength of defects are derived using a unified model convoluting homogeneous and heterogeneous mechanisms. In addition to the increased defect density, defect strength is found to decrease with increasing irradiation dose, suggesting a growth in defect size, which is further evidenced by combined analyses between pop-in and hardness tests.

36 MATERIALS SCIENCE↗

Local lattice distortion in NiCoCr, FeCoNiCr and FeCoNiCrMn concentrated alloys investigated by synchrotron X-ray diffraction

Severe lattice distortion is presumptively considered as a core effect of high-entropy alloys, but quantitative measurements are still missing. Here, we demonstrate that the lattice distortion in high-entropy alloys can be quantitatively analyzed based on pair distribution function obtained from synchrotron X-ray diffraction. By applying this method to equiatomic NiCoCr, FeCoNiCr and FeCoNiCrMn concentrated alloys, we found that the local lattice distortion in the NiCoCr (0.23%) and FeCoNiCrMn (0.24%) alloys are comparable while negligible in the FeCoNiCr alloy (0.04%). Furthermore, the origin of local lattice distortion in the NiCoCr and FeCoNiCrMn concentrated alloys was discussed.

36 MATERIALS SCIENCE↗

Single-Phase Concentrated Solid-Solution Alloys: Bridging Intrinsic Transport Properties and Irradiation Resistance

Single-phase concentrated solid-solution alloys (SP-CSAs), including high entropy alloys (HEAs), are compositionally complex but structurally simple, and provide a playground of tailoring material properties through modifying their compositional complexity. The recent progress in understanding the compositional effects on the energy and mass transport properties in a series of face-centered-cubic SP-CSAs is the focus of this review. Relatively low electrical and thermal conductivities, as well as small separations between the interstitial and vacancy migration barriers have been generally observed, but largely depend on the alloying constituents. We further discuss the impact of such intrinsic transport properties on their irradiation response; the linkage to the delayed damage accumulation, slow defect aggregation, and suppressed irradiation induced swelling and segregation has been presented. We emphasize that the number of alloying elements may not be a critical factor on both transport properties and the defect behaviors under ion irradiations. Furthermore, the recent findings have stimulated novel concepts in the design of new radiation-tolerant materials, but further studies are demanded to enable predictive models that can quantitatively bridge the transport properties to the radiation damage.

36 MATERIALS SCIENCE↗

Fabrication of highly dense isotropic Nd-Fe-B nylon bonded magnets via extrusion-based additive manufacturing [Fabrication of highly dense isotropic Nd-Fe-B bonded magnets via extrusion-based additive manufacturing]

Magnetically isotropic bonded magnets with a high loading fraction of 70 vol.% Nd-Fe-B are fabricated via an extrusion-based additive manufacturing, or 3D printing system that enables rapid production of large parts. The density of the printed magnet is ~5.2 g/cm 3 . The room temperature magnetic properties are: intrinsic coercivity H ci = 8.9 kOe (708.2 kA/m), remanence B r = 5.8 kG (0.58 T), and energy product (BH)max = 7.3 MGOe (58.1 kJ/m 3 ). The as-printed magnets are then coated with two types of polymers, both of which improve the thermal stability as revealed by flux aging loss measurements. Tensile tests performed at 25 °C and 100 °C show that the ultimate tensile stress (UTS) increases with increasing loading fraction of the magnet powder, and decreases with increasing temperature. AC magnetic susceptibility and resistivity measurements show that the 3D printed Nd-Fe-B bonded magnets exhibit extremely low eddy current loss and high resistivity. Lastly, we demonstrate the performance of the 3D printed magnets in a DC motor configuration via back electromotive force measurements.

36 MATERIALS SCIENCE↗