Engineering Papers⌕ Search

Engineering topics

Ji, Cheng

Publications and source records attributed to Ji, Cheng.

At least 19 records

Isolation of individual Er quantum emitters in anatase TiO 2 on Si photonics

Defects and dopant atoms in solid state materials are a promising platform for realizing single photon sources and quantum memories, which are the basic building blocks of quantum repeaters needed for long distance quantum networks. In particular, trivalent erbium (Er 3+ ) is of interest because it couples C-band telecom optical transitions with a spin-based memory platform. In order to produce quantum repeaters at the scale required for quantum networks it is imperative to integrate these necessary building blocks with mature and scalable semiconductor processes. Here, in this work, we demonstrate the optical isolation of single Er 3+ ions in CMOS-compatible titanium dioxide (TiO 2 ) thin films monolithically integrated on a silicon-on-insulator photonics platform. Our results demonstrate an initial step toward the realization of a monolithically integrated and scalable quantum photonics package based on Er 3+ doped thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Porous but Mechanically Robust All-Inorganic Antireflective Coatings Synthesized using Polymers of Intrinsic Microporosity

Herein, we introduce polymer of intrinsic microporosity 1 (PIM-1) to design single-layer and multilayered all-inorganic antireflective coatings (ARCs) with excellent mechanical properties. Using PIM-1 as a template in sequential infiltration synthesis (SIS), we can fabricate highly uniform, mechanically stable conformal coatings of AlO x with porosities of ~50% and a refractive index of 1.41 compared to 1.76 for nonporous AlO x that is perfectly suited for substrates commonly used in high-end optical systems or touch screens (e.g., sapphire, conductive glass, bendable glass, etc.). We show that such films can be used as a single-layer ARC capable of reduction of the Fresnel reflections of sapphire to as low as 0.1% at 500 nm being deposited only on one side of the substrate. We also demonstrate that deposition of the second layer with higher porosity using block copolymers enables the design of graded-index double-layered coatings. AlO x structures with just two layers and a total thickness of less than 200 nm are capable of reduction of Fresnel reflections under normal illumination to below 0.5% in a broad spectral range with 0.1% reflection at 700 nm. Additionally, and most importantly, we show that highly porous single-layer and graded-index double-layered ARCs are characterized by high hardness and scratch resistivity. The hardness and the maximum reached load were 7.5 GPa and 13 mN with a scratch depth of about 130 nm, respectively, that is very promising for the structures consisting of two porous AlO x layers with 50% and 85% porosities, correspondingly. Such mechanical properties of coatings can also allow their application as protective layers for other optical coatings.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamic-quenching of a single-photon avalanche photodetector using an adaptive resistive switch

One of the most common approaches for quenching single-photon avalanche diodes is to use a passive resistor in series with it. A drawback of this approach has been the limited recovery speed of the single-photon avalanche diodes. High resistance is needed to quench the avalanche, leading to slower recharging of the single-photon avalanche diodes depletion capacitor. We address this issue by replacing a fixed quenching resistor with a bias-dependent adaptive resistive switch. Reversible generation of metallic conduction enables switching between low and high resistance states under unipolar bias. As an example, using a Pt/Al 2 O 3 /Ag resistor with a commercial silicon single-photon avalanche diodes, we demonstrate avalanche pulse widths as small as ~30 ns, 10× smaller than a passively quenched approach, thus significantly improving the single-photon avalanche diodes frequency response. The experimental results are consistent with a model where the adaptive resistor dynamically changes its resistance during discharging and recharging the single-photon avalanche diodes.

42 ENGINEERING↗

Probing the Electronic Band Gap of Solid Hydrogen by Inelastic X-Ray Scattering up to 90 GPa

Metallization of hydrogen as a key problem in modern physics is the pressure-induced evolution of the hydrogen electronic band from a wide-gap insulator to a closed gap metal. However, due to its remarkably high energy, the electronic band gap of insulating hydrogen has never before been directly observed under pressure. Using high-brilliance, high-energy synchrotron radiation, we developed an inelastic x-ray probe to yield the hydrogen electronic band information in situ under high pressures in a diamond-anvil cell. Here, the dynamic structure factor of hydrogen was measured over a large energy range of 45 eV. The electronic band gap was found to decrease linearly from 10.9 to 6.57 eV, with an 8.6 times densification (ρ/ρ 0 ~ 8.6 ) from zero pressure up to 90 GPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Regulating off-centering distortion maximizes photoluminescence in halide perovskites

Abstract Metal halide perovskites possess unique atomic and electronic configurations that endow them with high defect tolerance and enable high-performance photovoltaics and optoelectronics. Perovskite light-emitting diodes have achieved an external quantum efficiency of over 20%. Despite tremendous progress, fundamental questions remain, such as how structural distortion affects the optical properties. Addressing their relationships is considerably challenging due to the scarcity of effective diagnostic tools during structural and property tuning as well as the limited tunability achievable by conventional methods. Here, using pressure and chemical methods to regulate the metal off-centering distortion, we demonstrate the giant tunability of photoluminescence (PL) in both the intensity (>20 times) and wavelength (>180 nm/GPa) in the highly distorted halide perovskites [CH3NH3GeI3, HC(NH2)2GeI3, and CsGeI3]. Using advanced in situ high-pressure probes and first-principles calculations, we quantitatively reveal a universal relationship whereby regulating the level of off-centering distortion towards 0.2 leads to the best PL performance in the halide perovskites. By applying this principle, intense PL can still be induced by substituting CH3NH3+ with Cs+ to control the distortion in (CH3NH3)1-xCsxGeI3, where the chemical substitution plays a similar role as external pressure. The compression of a fully substituted sample of CsGeI3 further tunes the distortion to the optimal value at 0.7 GPa, which maximizes the emission with a 10-fold enhancement. This work not only demonstrates a quantitative relationship between structural distortion and PL property of the halide perovskites but also illustrates the use of knowledge gained from high-pressure research to achieve the desired properties by ambient methods.

halide perovskites↗

Nitrogen in black phosphorus structure

Group V elements in crystal structure isostructural to black phosphorus with unique puckered two-dimensional layers exhibit exciting physical and chemical phenomena. However, as the first element of group V, nitrogen has never been found in the black phosphorus structure. Here, we report the synthesis of the black phosphorus–structured nitrogen at 146 GPa and 2200 K. Metastable black phosphorus–structured nitrogen was retained after quenching it to room temperature under compression and characterized in situ during decompression to 48 GPa, using synchrotron x-ray diffraction and Raman spectroscopy. We show that the original molecular nitrogen is transformed into extended single-bonded structure through gauche and trans conformations. Raman spectroscopy shows that black phosphorus–structured nitrogen is strongly anisotropic and exhibits high Raman intensities in two A g normal modes. Synthesis of black phosphorus–structured nitrogen provides a firm base for exploring new type of high-energy-density nitrogen and a new direction of two-dimensional nitrogen.

58 GEOSCIENCES↗

Crystallography of low Z material at ultrahigh pressure: Case study on solid hydrogen

Diamond anvil cell techniques have been improved to allow access to the multimegabar ultrahigh-pressure region for exploring novel phenomena in condensed matter. However, the only way to determine crystal structures of materials above 100 GPa, namely, X-ray diffraction (XRD), especially for low Z materials, remains nontrivial in the ultrahigh-pressure region, even with the availability of brilliant synchrotron X-ray sources. In this work,we perform a systematic study, choosing hydrogen (the lowest X-ray scatterer) as the subject, to understand how to better perform XRD measurements of low Z materials at multimegabar pressures. The techniques that we have developed have been proved to be effective in measuring the crystal structure of solid hydrogen up to 254 GPa at room temperature [C. Ji et al.,Nature 573, 558–562 (2019)]. We present our discoveries and experiences with regard to several aspects of this work, namely, diamond anvil selection, sample configuration for ultrahigh-pressure XRD studies,XRD diagnostics for low Z materials, and related issues in data interpretation and pressure calibration.We believe that these methods can be readily extended to other low Z materials and can pave the way for studying the crystal structure of hydrogen at higher pressures, eventually testing structural models of metallic hydrogen.

36 MATERIALS SCIENCE↗

Superconductivity in La and Y hydrides: Remaining questions to experiment and theory

Recent reports of the superconductivity in hydrides of two different families (covalent lattice, as in SH3 and clathrate-type H-cages containing La and Y atoms, as in LaH10 and YH6) have revealed new families of high-Tc materials with Tc’s near room temperature values. These findings confirm earlier expectations that hydrides may have very high Tc’s due to the fact that light H atoms have very high vibrational frequencies, leading to high Tc values within the conventional Bardeen–Cooper–Schrieffer phonon mechanism of superconductivity. However, as is pointed out by Ashcroft, it is important to have the metallic hydrogen “alloyed” with the elements added to it. This concept of a metallic alloy containing a high concentration of metal-like hydrogen atoms has been instrumental in finding new high-Tc superhydrides. These new superhydride “room-temperature” superconductors are stabilized only at very high pressures above 100 GPa, making the experimental search for their superconducting properties very difficult. We will review the current experimental and theoretical results for LaH10−x and YH6−x superhydrides.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Closure of Internal Porosity in Continuous Casting Bloom During Heavy Reduction Process

To investigate the closure behavior of internal porosity (also referred to as internal void) in continuous casting bloom during heavy reduction (HR) and thus provide theoretical guidance for minimizing this kind of internal defect more effectively with HR, a three-dimensional (3D) mechanical model was developed based on the predicted temperature field by a 2D heat transfer model. With this 3D mechanical model, closure behaviors of internal porosity in continuous casting bloom during HR at and after the strand solidification end under different process conditions were numerically studied. It was found that the void axis length decreased significantly along the bloom thickness direction and increased slightly along the casting and bloom width directions after HR, and the influence of the initial void size on the void closure was not obvious. With a decrease of temperature difference between the bloom surface and center, HR efficiency for minimizing internal void decreased, while the required reduction force significantly increased. Compared with blooms with a uniform temperature distribution of 1100 °C, the void closure index after HR implemented at the strand solidification end was increased by ~ 25 pct. Compared with a conventional flat roll, the application of a convex roll during HR could contribute to minimizing the internal porosity more effectively and significantly enhance the reduction capacity of the withdrawal and straightening units. The void closure index of η{sub s} and η{sub v} (where η{sub s} and η{sub v} were defined based on the variation of the void aspect ratio and the void volume, respectively) was closely related to the equivalent strain (ε{sub eq}) and the hydrostatic integration parameter (Q), respectively, and two mathematical equations were derived to quantitatively describe the relationship of η{sub s} − ε{sub eq} and η{sub v} − Q.

36 MATERIALS SCIENCE↗

Ultrahigh-pressure isostructural electronic transitions in hydrogen

High-pressure transitions are thought to modify hydrogen molecules to a molecular metallic solid and finally to an atomic metal, which is predicted to have exotic physical properties and the topology of a two-component (electron and proton) superconducting superfluid condensate. Therefore, understanding such transitions remains an important objective in condensed matter physics. However, measurements of the crystal structure of solid hydrogen, which provides crucial information about the metallization of hydrogen under compression, are lacking for most high-pressure phases, owing to the considerable technical challenges involved in X-ray and neutron diffraction measurements under extreme conditions. Here we present a single-crystal X-ray diffraction study of solid hydrogen at pressures of up to 254 gigapascals that reveals the crystallographic nature of the transitions from phase I to phases III and IV. Under compression, hydrogen molecules remain in the hexagonal close packed (hcp) crystal lattice structure, accompanied by a monotonic increase in anisotropy. In addition, the pressure-dependent decrease of the unit cell volume exhibits a slope change when entering phase IV, suggesting a second-order isostructural phase transition. Furthermore, our results indicate that the precursor to the exotic two-component atomic hydrogen may consist of electronic transitions caused by a highly distorted hcp Brillouin zone and molecular-symmetry breaking.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural basis for adenylation and thioester bond formation in the ubiquitin E1

The ubiquitin (Ub) and Ub-like (Ubl) protein-conjugation cascade is initiated by E1 enzymes that catalyze Ub/Ubl activation through C-terminal adenylation, thioester bond formation with an E1 catalytic cysteine, and thioester bond transfer to Ub/Ubl E2 conjugating enzymes. Each of these reactions is accompanied by conformational changes of the E1 domain that contains the catalytic cysteine (Cys domain). Open conformations of the Cys domain are associated with adenylation and thioester transfer to E2s, while a closed conformation is associated with pyrophosphate release and thioester bond formation. Several structures are available for Ub E1s, but none has been reported in the open state before pyrophosphate release or in the closed state. Here, we describe the structures of Schizosaccharomyces pombe Ub E1 in these two states, captured using semisynthetic Ub probes. In the first, with a Ub-adenylate mimetic (Ub-AMSN) bound, the E1 is in an open conformation before release of pyrophosphate. In the second, with a Ub-vinylsulfonamide (Ub-AVSN) bound covalently to the catalytic cysteine, the E1 is in a closed conformation required for thioester bond formation. These structures provide further insight into Ub E1 adenylation and thioester bond formation. Conformational changes that accompany Cys-domain rotation are conserved for SUMO and Ub E1s, but changes in Ub E1 involve additional surfaces as mutational and biochemical analysis of residues within these surfaces alter Ub E1 activities.

59 BASIC BIOLOGICAL SCIENCES↗

Design and Application of CSC-Roll for Heavy Reduction of the Bloom Continuous Casting Process

Center quality control is a key issue affecting large-section bloom production and product quality. The central convex roll could avoid the bloom side part and yield a high reduction amount, which benefit the implement of heavy reduction (HR) for bloom continuous casting process without upgrading the mechanical and hydraulic system of withdrawal and straightening machine. In this work, a curving surface convex roll (CSC-Roll), which could significantly improve bloom center quality, was designed by finite element simulation for a 360 mm × 450 mm #45 steel continuous casting bloom. The optimal roll surface shape of the CSC-Roll was determined based on an analysis of the distribution of the reduction amount in the bloom center and the strain of the bloom centerline and inner surface. The calculation results showed that the optimal size of the CSC-Roll was 200 mm in convex platform region length, 30 mm in convex platform region height, and 80 mm in gradient curvature region length. The bloom heat transfer and deformation behavior in the CSC-Roll reduction process were then analyzed. The results showed that in the CSC-Roll HR process, 61.71 pct of the reduction amount could be transmitted to the inner side of the porosity zone. Macrographs of the 360 mm × 450 mm #45 steel continuous casting bloom proved that the bloom center quality was significantly improved after CSC-Roll HR was applied.

36 MATERIALS SCIENCE↗

Numerical Simulation of V-shaped Segregation in Continuous Casting Blooms Based on a Microsegregation Model

This study establishes a volume-averaged model for transport phenomena to study V-shaped segregation in continuous casting blooms with different superheating and cooling rates by coupling fluid flow, macro-scale heat transfer, and solute transport. The results demonstrate that the modified Won–Thomas model considering back diffusion in the solid phase corresponds well with the measured carbon segregation. V-shaped segregation decreases with decreasing superheating and increases slightly with decreases in the cooling rate. The results of original position statistical distribution analysis correspond well with the simulation results. This phenomenon can be exploited to improve the quality of bloom.

42 ENGINEERING↗

Numerical Simulation of Bulging Deformation for Wide-Thick Slab Under Uneven Cooling Conditions

In the present work, the bulging deformation of a wide-thick slab under uneven cooling conditions was studied using finite element method. The non-uniform solidification was first calculated using a 2D heat transfer model. The thermal material properties were derived based on a microsegregation model, and the water flux distribution was measured and applied to calculate the cooling boundary conditions. Based on the solidification results, a 3D bulging model was established. The 2D heat transfer model was verified by the measured shell thickness and the slab surface temperature, and the 3D bulging model was verified by the calculated maximum bulging deflections using formulas. The bulging deformation behavior of the wide-thick slab under uneven cooling condition was then determined, and the effect of uneven solidification, casting speed, and roll misalignment were investigated.

36 MATERIALS SCIENCE↗

Amorphous boron oxide at megabar pressures via inelastic X-ray scattering

Structural transition in amorphous oxides, including glasses, under extreme compression above megabar pressures (>1 million atmospheric pressure, 100 GPa) results in unique densification paths that differ from those in crystals. Experimentally verifying the atomistic origins of such densifications beyond 100 GPa remains unknown. Progress in inelastic X-ray scattering (IXS) provided insights into the pressure-induced bonding changes in oxide glasses; however, IXS has a signal intensity several orders of magnitude smaller than that of elastic X-rays, posing challenges for probing glass structures above 100 GPa near the Earth’s core–mantle boundary. Here, we report megabar IXS spectra for prototypical B 2 O 3 glasses at high pressure up to ∼120 GPa, where it is found that only four-coordinated boron ( [4] B) is prevalent. The reduction in the [4] B–O length up to 120 GPa is minor, indicating the extended stability of sp 3 -bonded [4] B. In contrast, a substantial decrease in the average O–O distance upon compression is revealed, suggesting that the densification in B 2 O 3 glasses is primarily due to O–O distance reduction without the formation of [5] B. Together with earlier results with other archetypal oxide glasses, such as SiO 2 and GeO 2 , the current results confirm that the transition pressure of the formation of highly coordinated framework cations systematically increases with the decreasing atomic radius of the cations. These observations highlight a new opportunity to study the structure of oxide glass above megabar pressures, yielding the atomistic origins of densification in melts at the Earth’s core–mantle boundary.

58 GEOSCIENCES↗

Constitutive Modeling of the Flow Stress of GCr15 Continuous Casting Bloom in the Heavy Reduction Process

According to the calculation results of a 3D thermomechanical-coupled finite-element (FE) model of GCr15 bearing steel bloom during a heavy reduction (HR) process, the variation ranges in the strain rate and strain under HR were described. In addition, the hot deformation behavior of the GCr15 bearing steel was studied over the temperature range from 1023 K to 1573 K (750 °C to 1300 °C) with strain rates of 0.001, 0.01, and 0.1 s{sup −1} in single-pass thermosimulation compression experiments. To ensure the accuracy of the constitutive model, the temperature range was divided into two temperature intervals according to the fully austenitic temperature of GCr15 steel [1173 K (900 °C)]. Two sets of material parameters for the constitutive model were derived based on the true stress–strain curves of the two temperature intervals. A flow stress constitutive model was established using a revised Arrhenius-type constitutive equation, which considers the relationships among the material parameters and true strain. This equation describes dynamic softening during hot compression processes. Considering the effect of glide and climb on the deformation mechanism, the Arrhenius-type constitutive equation was modified by a physically based approach. This model is the most accurate over the temperatures ranging from 1173 K to 1573 K (900 °C to 1300 °C) under HR deformation conditions (ignoring the range from 1273 K to 1573 K (1000 °C to 1300 °C) with a strain rate of 0.1 s{sup −1}). To ensure the convergence of the FE calculation, an approximated method was used to estimate the flow stress at temperatures greater than 1573 K (1300 °C).

36 MATERIALS SCIENCE↗