Engineering topics
Publications and source records attributed to Jenkins, Jon M..
This release note discusses the science data products produced by the Science Processing Operations Center at Ames Research Center from Sector 1 observations made with the TESS spacecraft and cameras as a means to document instrument performance and data characteristics.
Stellar variability represents a key limitation on the detectability of weak transit signatures of small, Earth-size planets with space-based missions such as NASA's Kepler Mission or ESA's PLATO Mission. The expectations for the performance of the Kepler Mission in the face of solar-like variability were predicated on observations of the Sun with the Variability of Solar Irradiance and Gravity Oscillations (VIRGO) instrument aboard NASA and ESA's joint Solar and Heliospheric Observatory (SOHO) mission, which was launched in December 1995. Analyses of SOHO data indicated that solar-like variability would contribute approx.10 ppm to Kepler's noise budget at 6.5 ours, a typical grazing transit timescale. This proved to be optimistic as the typical 12th mag G2V star in the Kepler field of view exhibited 20 ppm of stellar variability-related noise at 6.5 hours, making the detection of true Earth-Sun analogs more difficult. While the consequent increase in the total noise at 6.5 hours from 20 ppm to 30 ppm could have been overcome by extending the mission to a total duration of 7 to 8 years. Unfortunately, a second reaction wheel failed in May 2013, ending the Kepler primary mission. Nevertheless, Kepler proved to be a veritable cornucopia of science results, both for exoplanets and for astrophysics. The phenomenal photometric precision and continuous observations required in order to identify small, rocky transiting planets enables the study of a large range of phenomena contributing to stellar variability for many thousands of solar-like stars in Kepler's field of view in exquisite detail. These effects range from less than 1 ppm acoustic oscillations on timescales from a few minutes and longward, to flares on timescales of hours, to spot-induced modulation on timescales of days to weeks to activity cycles on timescales of months to years. Kepler discovered over 2600 validated and confirmed exoplanets, and measured the pressure-mode oscillations of over 15000 stars over the course of its mission and the reconstituted K2 mission. We present the adaptive, wavelet-based matched filter used for both the Kepler and the TESS missions, and discuss the connections between this detection algorithm and fundamental detection theory, which allows the detector to function as a noise characterization engine. This provides a dynamical measurement of the photometric noise at transit timescales and thus, a key performance metric for missions like PLATO and Kepler. We give an overview of the stellar variability we see across the full range of spectral types observed by Kepler, from the cool, small red M stars to the hot, large late A stars, both in terms of amplitude as well as timescale.
Stellar variability represents a key limitation on the detectability of weak transit signatures of small, Earth-size planets with space-based missions such as NASA's Kepler Mission or ESA's PLATO Mission. The expectations for the performance of the Kepler Mission in the face of solar-like variability were predicated on observations of the Sun with the Variability of Solar Irradiance and Gravity Oscillations (VIRGO) instrument aboard NASA and ESA's joint Solar and Heliospheric Observatory (SOHO) mission, which was launched in December 1995. Analyses of SOHO data indicated that solar-like variability would contribute ~10 ppm to Kepler's noise budget at 6.5 ours, a typical grazing transit timescale. This proved to be optimistic as the typical 12th mag G2V star in the Kepler field of view exhibited 20 ppm of stellar variability-related noise at 6.5 hours, making the detection of true Earth-Sun analogs more difficult. While the consequent increase in the total noise at 6.5 hours from 20 ppm to 30 ppm could have been overcome by extending the mission to a total duration of 7 to 8 years. Unfortunately, a second reaction wheel failed in May 2013, ending the Kepler primary mission. Nevertheless, Kepler proved to be a veritable cornucopia of science results, both for exoplanets and for astrophysics. The phenomenal photometric precision and continuous observations required in order to identify small, rocky transiting planets enables the study of a large range of phenomena contributing to stellar variability for many thousands of solar-like stars in Kepler's field of view in exquisite detail. These effects range from <1 ppm acoustic oscillations on timescales from a few minutes and longward, to flares on timescales of hours, to spot-induced modulation on timescales of days to weeks to activity cycles on timescales of months to years. Kepler discovered over 2600 validated and confirmed exoplanets, and measured the pressure-mode oscillations of over 15000 stars over the course of its mission and the reconstituted K2 mission. We present the adaptive, wavelet-based matched filter used for both the Kepler and the TESS missions, and discuss the connections between this detection algorithm and fundamental detection theory, which allows the detector to function as a noise characterization engine. This provides a dynamical measurement of the photometric noise at transit timescales and thus, a key performance metric for missions like PLATO and Kepler. We give an overview of the stellar variability we see across the full range of spectral types observed by Kepler, from the cool, small red M stars to the hot, large late A stars, both in terms of amplitude as well as timescale.
The experience acquired through development, implementation and operation of the Kepler K2 science pipelines can provide lessons learned for the development of science pipelines for other missions such as NASA's Transiting Exoplanet Survey Satellite and ESA's PLATO mission.
This document describes data product formats and content that are produced primarily by the TESS Science Processing Operations Center (SPOC) at NASA Ames Research Center for archival to the Mikulski Archive for Space Telescopes (MAST) .
I present a description of the Kepler and TESS mission planet search pipelines, and discuss key science results achieved by Kepler and those expected for the TESS Mission.
I present a description of the Kepler and TESS (Transiting Exoplanet Survey Satellite) missions and key science results achieved by Kepler and those expected for the TESS Mission.
NASA's Kepler Mission was launched in March 2009 as NASA's first mission capable of finding Earth-size planets orbiting in the habitable zone of Sun-like stars, that range of distances for which liquid water would pool on the surface of a rocky planet. Kepler has discovered over 1000 planets and over 4600 candidates, many of them as small as the Earth. Today, Kepler's amazing success seems to be a fait accompli to those unfamiliar with her history. But twenty years ago, there were no planets known outside our solar system, and few people believed it was possible to detect tiny Earth-size planets orbiting other stars. Motivating NASA to select Kepler for launch required a confluence of the right detector technology, advances in signal processing and algorithms, and the power of supercomputing.
The Kepler Mission was designed to identify and characterize transiting planets in the Kepler Field of View and to determine their occurrence rates. Emphasis was placed on identification of Earth-size planets orbiting in the Habitable Zone of their host stars. Science data were acquired for a period of four years. Long-cadence data with 29.4 min sampling were obtained for approx. 200,000 individual stellar targets in at least one observing quarter in the primary Kepler Mission. Light curves for target stars are extracted in the Kepler Science Data Processing Pipeline, and are searched for transiting planet signatures. A Threshold Crossing Event is generated in the transit search for targets where the transit detection threshold is exceeded and transit consistency checks are satisfied. These targets are subjected to further scrutiny in the Data Validation (DV) component of the Pipeline. Transiting planet candidates are characterized in DV, and light curves are searched for additional planets after transit signatures are modeled and removed. A suite of diagnostic tests is performed on all candidates to aid in discrimination between genuine transiting planets and instrumental or astrophysical false positives. Data products are generated per target and planet candidate to document and display transiting planet model fit and diagnostic test results. These products are exported to the Exoplanet Archive at the NASA Exoplanet Science Institute, and are available to the community. We describe the DV architecture and diagnostic tests, and provide a brief overview of the data products. Transiting planet modeling and the search for multiple planets on individual targets are described in a companion paper. The final revision of the Kepler Pipeline code base is available to the general public through GitHub. The Kepler Pipeline has also been modified to support the Transiting Exoplanet Survey Satellite (TESS) Mission which is expected to commence in 2018.
NASAs Kepler Mission was launched in March 2009 as NASAs first mission capable of finding Earth-size planets orbiting in the habitable zone of Sun-like stars, that range of distances for which liquid water would pool on the surface of a rocky planet. Kepler has discovered over 2200 planets and over 2200 candidate planets, many of them as small as the Earth. Forty nine of these are less than twice the size of Earth and orbit in the habitable zone of their stars, all of which are cooler and significantly smaller than the Sun.Today, Keplers amazing success seems to be a fait accompli to those unfamiliar with her history. But twenty years ago, there were no planets known outside our solar system, and few people believed it was possible to detect tiny Earth-size planets orbiting other stars. Indeed, demonstrating that the science was feasible took four proposals to NASAs Discovery Program and extensive research and laboratory demonstrations. Motivating NASA to select Kepler for launch required a confluence of the right detector technology, advances in signal processing and algorithms, and the power of supercomputing. On August 23 2015 we reported the discovery of Kepler-452b, the first small, possibly rocky planet in the habitable zone of a G2 star very similar to our own. Kepler-452b orbits its star once every 385 days in an orbit just 5 larger than that of Earth. This discovery represents an important step towards finding and characterizing small habitable worlds orbiting Sun-like stars.
Two transit survey missions will have been flown by NASA prior to the launch of ESA's PLATO Mission in 2026, laying the groundwork for exoplanet discovery via the transit method. The Kepler Mission, which launched in 2009, collected data on its 100+ square degree field of view for four years before failure of a reaction wheel ended its primary mission. The results from Kepler include 2300+ confirmed or validated exoplanets, 2200+ planetary candidates, 2100+ eclipsing binaries. Kepler also revolutionized the field of asteroseismology by measuring the pressure mode oscillations of over 15000 solar-like stars spanning the lifecycle of such stars from hydrogen-burning dwarfs to helium-burning red giants. The re-purposed Kepler Mission, dubbed K2, continues to observe fields of view in and near the ecliptic plane for 80 days each, significantly broadening the scope of the astrophysical investigations as well as discovering an additional 156 exoplanets to date. The TESS mission will launch in 2017 to conduct an all-sky survey for small exoplanets orbiting stars 10X closer and 100X brighter than Kepler exoplanet host stars, allowing for far greater follow-up and characterization of their masses as well as their sizes for at least 50 small planets. Future assets such as James Webb Space Telescope, and ground-based assets such as ESOs Very Large Telescope (VLT) array, the Exremely Large Telescope (ELT), and the Thirty Meter Telescope (TMT) will be able to characterize the atmospheric composition and properties of these small planets. TESS will observe each 24 X 96 field of view for 30 days and thereby cover first the southern and then the northern hemisphere over 13 pointings during each year of the primary mission. The pole-most camera will observe the James Webb continuous viewing zone for one year in each hemisphere, permitting much longer period planets to be detected in this region. The PLATO mission will seek to detect habitable Earth-like planets with an instrument composed of 26 small telescopes in several 2232 square deg FOVs with a range of observation durations over a mission lifetime of up to eight years. This paper summarizes the findings of the KeplerK2 missions, previews the likely results from the TESS mission, and explores the lessons learned and to be learned from these prior missions that can be incorporated into the observation and data reduction strategy for the PLATO Mission so as to maximize the science return.
The experience acquired through development, implementation and operation of the KeplerK2 science pipelines can provide lessons learned for the development of science pipelines for other missions such as NASA's Transiting Exoplanet Survey Satellite, and ESA's PLATO mission.
The Transiting Exoplanet Survey Satellite (TESS) science pipeline is being developed by the Science Processing Operations Center (SPOC) at NASA Ames Research Center based on the highly successful Kepler Mission science pipeline. Like the Kepler pipeline, the TESS science pipeline will provide calibrated pixels, simple and systematic error-corrected aperture photometry, and centroid locations for all 200,000+ target stars, observed over the 2-year mission, along with associated uncertainties. The pixel and light curve products are modeled on the Kepler archive products and will be archived to the Mikulski Archive for Space Telescopes (MAST). In addition to the nominal science data, the 30-minute Full Frame Images (FFIs) simultaneously collected by TESS will also be calibrated by the SPOC and archived at MAST. The TESS pipeline will search through all light curves for evidence of transits that occur when a planet crosses the disk of its host star. The Data Validation pipeline will generate a suite of diagnostic metrics for each transit-like signature discovered, and extract planetary parameters by fitting a limb-darkened transit model to each potential planetary signature. The results of the transit search will be modeled on the Kepler transit search products (tabulated numerical results, time series products, and pdf reports) all of which will be archived to MAST.
The Kepler telescope hurtled into orbit in March 2009, initiating NASA's first mission to discover Earth-size planets orbiting Sun-like stars. Kepler simultaneously collected data for approximately 165,000 target stars at a time over its four-year mission, identifying over 4700 planet candidates, over 2300 confirmed or validated planets, and over 2100 eclipsing binaries. While Kepler was designed to discover exoplanets, the long-term, ultrahigh photometric precision measurements it achieved made it a premier observational facility for stellar astrophysics, especially in the field of asteroseismology, and for variable stars, such as RR Lyrae. The Kepler Science Operations Center (SOC) was developed at NASA Ames Research Center to process the data acquired by Kepler from pixel-level calibrations all the way to identifying transiting planet signatures and subjecting them to a suite of diagnostic tests to establish or break confidence in their planetary nature. Detecting small, rocky planets transiting Sun-like stars presents a variety of daunting challenges, including achieving an unprecedented photometric precision of ~20 ppm on 6.5-hour timescales, and supporting the science operations, management, processing, and repeated reprocessing of the accumulating data stream. A newly revised and expanded version of the Kepler Data Processing Handbook (KDPH) has been released to support the legacy archival products. The KDPH details the theory, design and performance of the algorithms supporting each data processing step. This paper presents an overview of the KDPH and features illustrations of several key algorithms in the Kepler Science Data Processing Pipeline. Kepler was selected as the 10th mission of the Discovery Program. Funding for this mission is provided by NASA, Science Mission Directorate.
NASA's Kepler Mission was launched in March 2009 as NASA's first mission capable of finding Earth-size planets orbiting in the habitable zone of Sun-like stars, that range of distances for which liquid water would pool on the surface of a rocky planet. Kepler has discovered over 1000 planets and over 4600 candidates, many of them as small as the Earth. Today, Kepler's amazing success seems to be a fait accompli to those unfamiliar with her history. But twenty years ago, there were no planets known outside our solar system, and few people believed it was possible to detect tiny Earth-size planets orbiting other stars. Motivating NASA to select Kepler for launch required a confluence of the right detector technology, advances in signal processing and algorithms, and the power of supercomputing.
The Kepler telescope launched into orbit in March 2009, initiating NASAs first mission to discover Earth-size planets orbiting Sun-like stars. Kepler simultaneously collected data for 160,000 target stars at a time over its four-year mission, identifying over 4700 planet candidates, 2300 confirmed or validated planets, and over 2100 eclipsing binaries. While Kepler was designed to discover exoplanets, the long term, ultra- high photometric precision measurements it achieved made it a premier observational facility for stellar astrophysics, especially in the field of asteroseismology, and for variable stars, such as RR Lyraes. The Kepler Science Operations Center (SOC) was developed at NASA Ames Research Center to process the data acquired by Kepler from pixel-level calibrations all the way to identifying transiting planet signatures and subjecting them to a suite of diagnostic tests to establish or break confidence in their planetary nature. Detecting small, rocky planets transiting Sun-like stars presents a variety of daunting challenges, from achieving an unprecedented photometric precision of 20 parts per million (ppm) on 6.5-hour timescales, supporting the science operations, management, processing, and repeated reprocessing of the accumulating data stream. This paper describes how the design of the SOC meets these varied challenges, discusses the architecture of the SOC and how the SOC pipeline is operated and is run on the NAS Pleiades supercomputer, and summarizes the most important pipeline features addressing the multiple computational, image and signal processing challenges posed by Kepler.
We give an overview of the operational concepts and architecture of the Kepler Science Processing Pipeline. Designed, developed, operated, and maintained by the Kepler Science Operations Center (SOC) at NASA Ames Research Center, the Science Processing Pipeline is a central element of the Kepler Ground Data System. The SOC consists of an office at Ames Research Center, software development and operations departments, and a data center which hosts the computers required to perform data analysis. The SOC's charter is to analyze stellar photometric data from the Kepler spacecraft and report results to the Kepler Science Office for further analysis. We describe how this is accomplished via the Kepler Science Processing Pipeline, including, the software algorithms. We present the high-performance, parallel computing software modules of the pipeline that perform transit photometry, pixel-level calibration, systematic error correction, attitude determination, stellar target management, and instrument characterization.
The Transiting Exoplanet Survey Satellite (TESS) will conduct a search for Earth's closest cousins starting in early 2018 and is expected to discover approximately 1,000 small planets with R(sub p) less than 4 (solar radius) and measure the masses of at least 50 of these small worlds. The Science Processing Operations Center (SPOC) is being developed at NASA Ames Research Center based on the Kepler science pipeline and will generate calibrated pixels and light curves on the NASA Advanced Supercomputing Division's Pleiades supercomputer. The SPOC will also search for periodic transit events and generate validation products for the transit-like features in the light curves. All TESS SPOC data products will be archived to the Mikulski Archive for Space Telescopes (MAST).