Engineering Papers⌕ Search

Engineering topics

Jansen, Andrew

Publications and source records attributed to Jansen, Andrew.

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Engineering Microstructure in Dry-Processed Cathodes Via Calendering

Calendering serves as a multifunctional step in dry electrode processing that not only densifies the electrode but also induces polytetrafluoroethylene (PTFE) fibrillation and reorganizes the microstructure. These coupled effects are essential for achieving electrical connectivity and sufficient cohesion, yet they also introduce trade-offs, such as active material particle fracture, pore collapse, and excessive porosity loss, that can hinder ionic transport. This research systematically maps the calendering parameter space for LiNi0.6Mn0.2Co0.2O2 (NMC622) dry cathodes with a target thickness of ∼100 µm and porosity of ∼30% by varying roll gaps, roll temperature, roll speed, and the number of passes. A practical processing window for this formulation and electrode architecture is identified that achieves sufficient PTFE fibrillation and strong interfacial contact while minimizing particle fracture and preserving the porosity required for efficient ionic transport. In particular, gradual-gap calendering with moderate per-pass compression mitigates fracture and pore collapse while still reaching the target thickness with reasonable throughput, and slower roll speeds with modest roll temperatures further reduce mechanical damage. These results provide actionable guidance for scaling NMC622-based thick dry-processed cathodes.

Park, Hyunji↗
DOE OSTI2024

EVALS: Enhanced VALidation of Advanced Battery Supply Chains

This is an overview of EVALS (Enhanced VALidation of advanced battery Supply chains), funded by the U.S. Department of Energy Vehicle Technologies Office (VTO) and some initial data from a transformational laboratory directed research and development (LDRD) program project funded at NREL. EVALS aims to accelerate the process to bring domestic and allied primary sources of battery materials online, from production to deployment.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Solvents and slurries comprising a poly(carboxylic acid) binder for silicon electrode manufacture

An silicon-containing electrode is formed by coating a silicon-containing slurry onto a conductive current collector. The slurry comprises a binder solution comprising a poly(carboxylic acid) binder dissolved in a mixed solvent system comprising an amide solvent of Formula I, as described herein, and a second solvent which can be water and/or an organic solvent. The binder preferably comprises poly(acrylic acid). The mixed solvent system comprises about 10 to about 99 vol % of the amide solvent of Formula I. The binder solution is utilized as a solvent for a slurry of silicon-containing particles for preparing the silicon-containing electrode. The slurries comprising the mixed solvent system have higher viscosity and are more stable than slurries containing the same concentrations of silicon particles, carbon particles, and binder in water as the sole solvent.

Zhang, Lu↗
DOE OSTI2023

Understanding and Mitigating the Dissolution and Delamination Issues Encountered with High-Voltage LiNi 0.5 Mn 1.5 O 4

In our initial study on the high-voltage 5 V cobalt-free spinel LiNi 0.5 Mn 1.5 O 4 (LNMO) cathode, we discovered a severe delamination issue in the laminates when cycled at a high upper cut-off voltage (UCV) of 4.95 V, especially when a large cell format was used. This delamination problem prompted us to investigate further by studying the transition metal (TM) dissolution mechanism of cobalt-free LNMO cathodes, and as a comparison, some cobalt-containing lithium nickel manganese cobalt oxides (NMC) cathodes, as the leachates from the soaking experiment might be the culprit for the delamination. Unlike other previous reports, we are interested in the intrinsic stability of the cathode in the presence of a baseline Gen2 electrolyte consisting of 1.2 M of LiPF 6 in ethylene carbonate/ethyl methyl carbonate (EC/EMC), similar to a storage condition. The electrode laminates (transition metal oxides, transition metal oxides, TMOs, coated on an Al current collector with a loading level of around 2.5 mAh/cm 2 ) or the TMO powders (pure commercial quality spinel LNMO, NMC, etc.) were stored in the baseline solution, and the transition metal dissolution was studied through nuclear magnetic resonance, such as 1 H NMR, 19 F NMR, scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma mass spectrometry (ICP-MS). Significant electrolyte decomposition was observed and could be the cause that leads to the TM dissolution of LNMO. To address this TM dissolution, additives were introduced into the baseline electrolyte, effectively alleviating the issue of TM dissolution. The results suggest that the observed delamination is caused by electrolyte decompositions that lead to etching, and additives such as lithium difluorooxalato borate and p-toluenesulfonyl isocyanate can alleviate this issue by forming a firm cathode electrolyte interface. This study provides a new perspective on cell degradation induced by electrode/electrolyte interactions under storage conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

Solvents and slurries comprising a poly(carboxylic acid) binder for silicon electrode manufacture

A binder solution for manufacturing silicon-based anodes useful for lithium-ion electrochemical cells is described herein. The binder solution comprises a poly(carboxylic acid) binder dissolved in a mixed solvent system comprising an amide solvent of Formula I, as described herein, and a second solvent which can be water and/or an organic solvent. The binder preferably comprises poly(acrylic acid). The mixed solvent system comprises about 10 to about 99 vol % of the amide solvent of Formula I. The binder solution is utilized as a solvent for a slurry of silicon-containing particles for preparing a silicon-containing electrode. The slurries made with the mixed solvent systems have higher viscosity and are more stable than slurries containing the same concentrations of silicon particle, carbon particles, and binder in water as the sole solvent.

Zhang, Lu↗
DOE OSTI2022

Extreme fast charge aging: Effect of electrode loading and NMC composition on inhomogeneous degradation in graphite bulk and electrode/electrolyte interface

Empowering extreme fast charging (XFC) requires a comprehensive understanding of its application with advanced anode and cathode materials in lithium-ion batteries. No report exists for the full extent of limitations for the anode with crosstalk effect from paired cathode as well as Li plating due to electrode loading under XFC. In this study, a combination of cell testing and multiple length characterization is used to investigate XFC aging mechanism in cells with a low loading of 1.5 mAh cm -2 and high loading of 2.5 mAh cm -2 for graphite (Gr)/Ni-rich LiNi x Mn y Co 1-x-y O 2 (NMCs). Operando XRD mappings show 1.5 mAh cm -2 loadings result in higher strain in graphite for all three cathode types. Among the three NMC cathodes, the graphite from NMC532 and NMC811 cells show comparable strain. Scanning electron microscopy (SEM) images show distinct differences between 6-C-charged anodes in two loadings. Significantly increased electrode thickness can be seen due to more damage in the graphite bulk and accumulation of the electrolyte decomposition products in electrode pores. X-ray photoelectron spectroscopy (XPS) reveals both cathode chemistry and Li plating influence the non-uniform SEI composition on graphite surface. We report higher Ni content in NMC811 promotes the higher levels of salt decomposition on the SEI and formation of higher mass of electrolyte aging products.

25 ENERGY STORAGE↗
DOE OSTI2022

Extreme fast charge aging: Correlation between electrode scale and heterogeneous degradation in Ni-rich layered cathodes

Extreme fast charging (XFC) is a key requirement for the adoption of battery-based electric vehicles by the transportation sector. However, XFC has been shown to accelerate degradation, causing the capacity, life, and safety of batteries to deteriorate. There are no systematic studies in the open literature regarding aging modes in Ni-rich Li y Ni 0.a Mn 0.b Co 0.c O 2 (NMCabc) cathodes caused by fast charging. Herein, we report the effects of cathode composition and electrode loading in pouch cells containing NMC532, 622 and 811 paired with graphite and cycled under XFC conditions. The relative anisotropic volume change in the unit cell increases with Ni content in low-loading cells, while it levels up for all three NMC cathodes in high-loading cells because of substantial Li plating. The amounts of lithium plating and heterogeneity on the anode, determined by crystallographic phase quantification, were found to be correlated with electrode loading and cathode heterogeneity. The concentrations of the transition metals deposited on the anodes depend on NMCabc composition in a complex way. More particle cracking and surface degradation was found in NMC811. Here, the findings in this work provide a new understanding of the failure mechanisms and their practical implications for compositional tuning of future high-Ni NMCabc cathode materials during fast charging.

25 ENERGY STORAGE↗
DOE OSTI2021

Effect of cathode on crosstalk in Si-based lithium-ion cells

Crosstalk between the cathode and the anode in Li-ion batteries has a great impact on performance, safety and cycle lifetime. However, a systematic investigation of crosstalk behavior in silicon (Si)-based cells with various cathode materials has not been reported. We investigated the crosstalk behavior of a Si anode coupled with one of the following cathodes—LiCoO 2 (LCO), LiNi 0.5 Mn 0.3 Co 0.2 (NMC532), and LiFePO 4 (LFP)—in a full cell. For each electrochemical couple, we compared electrolyte decomposition products, solid electrolyte interphase (SEI) chemistry, and degradation mechanisms during cycling. From a very early stage of cycling, each couple showed different crosstalk behavior; different electrolyte decomposition products and SEI chemistry on the Si anodes were seen. Specifically, the formation and growth mechanism of Si SEI differ depending on cathode materials. For the LFP system, the Si SEI rich in LiF and inorganic species, which is stable and robust. It forms at an early stage of cycle. As a result, the SEI of Si from the LFP system well tolerates SEI breakage due to mechanical changes of Si and suppresses Li loss, resulting in stable cycle life.

25 ENERGY STORAGE↗
DOE OSTI2021

Methodologies for Design, Characterization and Testing of Electrolytes that Enable Extreme Fast Charging of Lithium-ion Cells

Selection, testing and validation of electrolyte candidates for Li-ion cells are discussed, based on a 10-minute target for extreme fast charge (XFC). A combination of modeling and laboratory measurements create a timely and synergistic approach to identifying candidate electrolyte formulations. Multi-solvent systems provide a balanced set of properties, wherein lower molecular-weight solvents offer reduced viscosity, increased species diffusivity, and mitigation of concentration polarization at high charge rates. Carefully selected formulations can exhibit peak conductivity and usable conductivity range of two to three times that of the baseline EC-EMC (3:7, wt.) + LiPF 6 . Candidates are also chosen based on stability and longevity within the cell environment. Lab testing coincides with property predictions from the Advanced Electrolyte Model (AEM) and a macro-scale cell model. Furthermore, cell testing utilized coin and pouch cells having NMC532 or NMC811 cathodes with graphite electrodes. Results indicate combinations of low-molecular weight solvents are key for fast-charge electrolytes as they extend the useful conductivity range to both low and higher salt concentrations, and possess higher self-diffusivities compared to conventional solvents. This reduces impacts from concentration polarization. The choice of electrolyte also influences the tendency for lithium metal deposition at the anode, as showcased by experimental and modeling results herein.

25 ENERGY STORAGE↗
DOE OSTI2020

Optimization of Graphite–SiO blend electrodes for lithium-ion batteries: Stable cycling enabled by single-walled carbon nanotube conductive additive

Lithium-alloying materials are of great interest to improve the gravimetric and volumetric energy density of lithium-ion batteries, though their associated volume fluctuation with cycling often leads to poor cycling performance. Active-inactive alloys and blending alloys with carbon materials are common strategies to accommodate volume fluctuation. Herein we set out to optimize graphite-SiO blend electrode formulations to eliminate rapid capacity fade. Electrodes with highly stable cycling were prepared by simple planetary mixing procedures, enabled by the use of just a fraction of a weight percent of commercial SWCNTs as the only conductive additive, and by the appropriate choice of binder/stabilizing agent. In fact, the use of SWCNTs allowed for graphite-free SiO electrodes with approximately 74% higher volumetric energy density relative to traditional graphite electrodes, and superior capacity retention in coin-type full-cell testing versus NMC532 cathodes.

25 ENERGY STORAGE↗
DOE OSTI2019

Understanding of pre-lithiation of poly(acrylic acid) binder: Striking the balances between the cycling performance and slurry stability for silicon-graphite composite electrodes in Li-ion batteries

Poly(acrylic acid) (PAA) is widely used as a polymer binder for high capacity silicon (Si) anodes in Li-ion batteries. When used, the carboxyl (-CO2H) groups of PAA can be partially lithiated (known as pre-lithiation treatment), which is believed to facilitates lamination process, especially for production on a large scale. However, such treatment impacts numerous physico-chemical properties of the PAA binder that affect the cycling performance of the electrode. Here we seek to quantify the pre-lithiation treatment effect on Li-ion cells containing Si-graphite composite electrodes. The electrochemical cycling results indicated that such pre-lithiation treatment of PAA can undermine the cycling performance, as more capacity loss was observed when pre-lithitated PAA binders were used. On the other hand, the same pre-lithiation practice is indeed beneficial for the lamination process, as it increases the viscosity of aqueous slurries at low shear rates (slows down sedimentation) and prompts the shear thinning (so that the slurries can be more easily mixed). Thus, there is an uneasy balance between the electrochemical performance that suffers from the pre-lithiation of PAA and the quality of slurry processing which benefits from the same practice. An alternative approach to slurry treatment would be desired to achieve better cycling performance without undermining the stability of slurry suspensions.

25 ENERGY STORAGE↗