Engineering Papers⌕ Search

Engineering topics

Janek, Jürgen

Publications and source records attributed to Janek, Jürgen.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Evaluating Pressure‐dependent Discharge Behavior of Foil Versus In situ Plated Lithium Metal Anodes in Solid‐State Batteries

Abstract Anode‐free manufacturing of solid‐state batteries (SSBs) shows promise to maximize energy density by eliminating excess lithium (Li) and simplifying battery production. However, high reversibility during discharge (stripping of Li) is necessary for long‐lifetime SSBs with a limited Li reservoir. Further, the plastic flow of Li changes depending on the Li thickness, leading to possible differences in discharge performance under stack pressure. This work investigates the pressure‐dependent discharge performance of anode‐free manufactured SSBs with in situ plated Li and compares the performance to that of conventional thick Li foil cells. Distinct stripping behavior is observed at low pressures (0–1 MPa), where Li diffusivity and initial interfacial contact may control accessible capacity, compared to high pressures (3–10 MPa) where mechanical deformation of Li likely governs stripping behavior. Analysis of impedance spectra collected during stripping shows that additional stack pressure delays the formation of deep, as opposed to lateral, voids in the Li anode. These results provide insights to guide the transition from thick Li foil anodes to anode‐free manufactured SSBs.

Haslam, Catherine G.↗
DOE OSTI2024

Study of Void Formation at the Lithium|Solid Electrolyte Interface

There is growing recognition of the critical role of void formation in lithium metal anodes in solid-state batteries and its impact on electrochemical performance. While experimental studies have demonstrated the challenges ensuing from void formation at the lithium metal interface with the solid electrolyte, there is a need to understand and quantify the role of intrinsic transport properties in lithium metal and the impact of external stimuli, such as temperature, pressure, and current density. Here, we develop this understanding by constructing a phase field-based model that captures the evolution of void domains at the lithium-solid electrolyte interface. Growth of the pores is driven by the fast removal of lithium from the interface during stripping at high current densities. Relative magnitudes of the bulk and surface lithium diffusivities, along with the applied current density, dictate the final pore morphology. Increasing the temperature results in faster diffusion, while external applied pressure causes creep flow of lithium, both of which help to mitigate the evolution of voids by quickly transporting metal from the bulk to the interface. Finally, a phase map as a function of temperature and pressure is developed as a guide to determine the regions that can lead to the stable cycling of lithium metal.

25 ENERGY STORAGE↗
DOE OSTI2024

Designing lithium halide solid electrolytes

All-solid-state lithium batteries have attracted widespread attention for next-generation energy storage, potentially providing enhanced safety and cycling stability. The performance of such batteries relies on solid electrolyte materials; hence many structures/phases are being investigated with increasing compositional complexity. Among the various solid electrolytes, lithium halides show promising ionic conductivity and cathode compatibility, however, there are no effective guidelines when moving toward complex compositions that go beyond ab -initio modeling. Here, we show that ionic potential, the ratio of charge number and ion radius, can effectively capture the key interactions within halide materials, making it possible to guide the design of the representative crystal structures. This is demonstrated by the preparation of a family of complex layered halides that combine an enhanced conductivity with a favorable isometric morphology, induced by the high configurational entropy. This work provides insights into the characteristics of complex halide phases and presents a methodology for designing solid materials.

25 ENERGY STORAGE↗
DOE OSTI2023

Li 3– x Zr x (Ho/Lu) 1– x Cl 6 Solid Electrolytes Enable Ultrahigh-Loading Solid-State Batteries with a Prelithiated Si Anode

We report two new families of lithium metal chloride solid electrolytes Li 3–x Zr x (M) 1–x Cl 6 (0 ≤ x ≤ 0.8; M = Ho or Lu) with ionic conductivities of up to 1.8 mS cm –1 and a low activation energy of 0.34 eV. Structural elucidation via high-resolution neutron diffraction determines the Li ion distribution in trigonal Li 3 HoCl 6 , orthorhombic-I Li 3 LuCl 6 , and orthorhombic-II Li 2.4 Zr 0.6 (Ho/Lu) 0.4 Cl 6 . The last compound exhibits well-connected Li-ion pathways and abundant Li-ion carriers/vacancies to promote diffusion. All-solid-state batteries with Li 2.6 Zr 0.4 (Ho/Lu) 0.6 Cl 6 solid electrolytes and NCM85 cathodes exhibit stable cycling up to 4.6 V vs Li + /Li, which is even preserved up to 4.8 V. Stable cathode interphases are formed for both electrolytes upon cycling to 4.3, 4.6, and 4.8 V cutoff potentials, as identified by a ToF-SIMS analysis. Solid-state cells with a prelithiated Li 0.7 Si anode exhibit a significantly increased initial coulombic efficiency of 94.5% compared to Si and a high areal capacity of up to 16.3 mAh·cm –2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Non‐Linear Kinetics of The Lithium Metal Anode on Li 6 PS 5 Cl at High Current Density: Dendrite Growth and the Role of Lithium Microstructure on Creep

Abstract Interfacial instability, viz., pore formation in the lithium metal anode (LMA) during discharge leading to high impedance, current focusing induced solid–electrolyte (SE) fracture during charging, and formation/behaviour of the solid–electrolyte interphase (SEI), at the anode, is one of the major hurdles in the development of solid‐state batteries (SSBs). Also, understanding cell polarization behaviour at high current density is critical to achieving the goal of fast‐charging battery and electric vehicle. Herein, via in situ electrochemical scanning electron microscopy (SEM) measurements, performed with freshly deposited lithium microelectrodes on transgranularly fractured fresh Li6PS5Cl (LPSCl), the LiǀLPSCl interface kinetics are investigated beyond the linear regime. Even at relatively small overvoltages of a few mV, the LiǀLPSCl interface shows non‐linear kinetics. The interface kinetics possibly involve multiple rate‐limiting processes, i.e., ion transport across the SEI and SE|SEI interfaces, as well as charge transfer across the LiǀSEI interface. The total polarization resistance R P of the microelectrode interface is determined to be ≈ 0.8 Ω cm 2 . It is further shown that the nanocrystalline lithium microstructure can lead to a stable LiǀSE interface via Coble creep along with uniform stripping. Also, spatially resolved lithium deposition, i.e., at grain surface flaws, grain boundaries, and flaw‐free surfaces, indicates exceptionally high mechanical endurance of flaw‐free surfaces toward cathodic load (>150 mA cm −2 ). This highlights the prominent role of surface defects in dendrite growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Origin of the lithium metal anode instability in solid-state batteries during discharge

Enabling the lithium metal anode (LMA) in solid-state batteries (SSBs) would increase energy density and specific energy compared with lithium-ion batteries. However, pore formation in LMAs with irregular morphology, even at low current density, during discharge results in an unstable, high-impedance interface. Understanding and addressing this inherent anode instability is essential for increasing the power densities in SSBs. Herein, we suggest that the morphology of the stripped electrode is related to dislocations in the LMA. To investigate the influence of dislocations, symmetric cells, Li|Li 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO)|X-Li, are studied, where X-Li represents the microstructurally controlled LMA obtained via suitable thermomechanical processing. Operando impedance measurements are corroborated with SEM, confocal microscopy, and AFM data. Based on the experimental observations, a mechanism for pore formation is proposed. Here we show that the stack pressure required to maintain a stable interface is governed by the lithium microstructure and its thermomechanical processing history.

25 ENERGY STORAGE↗
DOE OSTI2023

Reaction Current Heterogeneity at the Interface between a Lithium Electrode and Polymer/Ceramic Composite Electrolytes

Although lithium metal anodes are expected to increase the energy density of next-generation batteries, dendrite growth during charge remains a major bottleneck preventing widespread implementation. Composite solid electrolytes with ceramic particles embedded in a polymer matrix have the potential to prevent dendrites owing to the higher mechanical stiffness while also possessing the flexibility to maintain contact with the electrode. However, microscopically, the different mechanical and electrochemical properties of the polymer and ceramic domains can cause inhomogeneous charge transfer at the Li/electrolyte interface, which can lead to nonuniform Li deposition and propagation of dendrites. Here, we computationally examine the coupled electrochemical, transport, and mechanical processes at the interface to determine the propensity for dendrite formation and possible approaches to mitigate this issue. Predictions of two possible microstructures at the interface, namely, (i) where both the polymer and ceramic come in contact with Li metal and (ii) when only the polymer comes in contact with Li metal, suggest that the former has a greater tendency for nonuniform plating. In addition, predictions suggest that minimizing the interfacial resistance between polymers and ceramics and incorporating interlayers between the electrode and electrolyte help mitigate current heterogeneity. In conclusion, these predictions provide guidance for experimental approaches to prevent dendrites in composite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2022

Oxide‐Based Solid‐State Batteries: A Perspective on Composite Cathode Architecture

Abstract The garnet‐type phase Li 7 La 3 Zr 2 O 12 (LLZO) attracts significant attention as an oxide solid electrolyte to enable safe and robust solid‐state batteries (SSBs) with potentially high energy density. However, while significant progress has been made in demonstrating compatibility with Li metal, integrating LLZO into composite cathodes remains a challenge. The current perspective focuses on the critical issues that need to be addressed to achieve the ultimate goal of an all‐solid‐state LLZO‐based battery that delivers safety, durability, and pack‐level performance characteristics that are unobtainable with state‐of‐the‐art Li‐ion batteries. This perspective complements existing reviews of solid/solid interfaces with more emphasis on understanding numerous homo‐ and heteroionic interfaces in a pure oxide‐based SSB and the various phenomena that accompany the evolution of the chemical, electrochemical, structural, morphological, and mechanical properties of those interfaces during processing and operation. Finally, the insights gained from a comprehensive literature survey of LLZO–cathode interfaces are used to guide efforts for the development of LLZO‐based SSBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Overcoming Anode Instability in Solid‐State Batteries through Control of the Lithium Metal Microstructure

Abstract Enabling the lithium metal anode (LMA) in solid‐state batteries (SSBs) is the key to developing high energy density battery technologies. However, maintaining a stable electrode–electrolyte interface presents a critical challenge to high cycling rate and prolonged cycle life. One such issue is the interfacial pore formation in LMA during stripping. To overcome this, either higher stack pressure or binary lithium alloy anodes are used. Herein, it is shown that fine‐grained ( d = 20 µm) polycrystalline LMA can avoid pore formation by exploiting the microstructural dependence of the creep rates. In a symmetric cell set‐up, i.e., LiǀLi 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO)ǀLi, fine‐grained LMA achieves > 11.0 mAh cm −2 compared to ≈ 3.6 mAh cm −2 for coarse‐grained LMA ( d = 295 µm) at 0.1 mA cm −2 and at moderate stress of 2.0 MPa. Smaller diffusion lengths (≈ 20 µm) and higher diffusivity pathway along dislocations ( D d ≈ 10 −7 cm 2 s −1 ), generated during cell fabrication, result in enhanced viscoplastic deformation in fine‐grained polycrystalline LMA. The electrochemical performances corroborate well with estimated creep rates. Thus, microstructural control of LMA can significantly reduce the required stack pressure during stripping. These results are particularly relevant for “anode‐free” SSBs wherein both the microstructure and the mechanical state of the lithium are critical parameters.

25 ENERGY STORAGE↗
DOE OSTI2022

Current‐Dependent Lithium Metal Growth Modes in “Anode‐Free” Solid‐State Batteries at the Cu|LLZO Interface

Abstract Controlling the lithium growth morphology in lithium reservoir‐free cells (RFCs), so‐called “anode‐free” solid‐state batteries, is of key interest to ensure stable battery operation. Despite several benefits of RFCs like improved energy density and easier fabrication, issues during the charging of the cell hinder the transition from lithium metal batteries with a lithium reservoir layer to RFCs. In RFCs, the lithium metal anode is plated during the first charging step at the interface between a metal current collector and the solid electrolyte, which is prone to highly heterogeneous growth instead of the desired homogeneous film‐like growth. Herein, the lithium morphology during the first charging step in RFCs is explored as a function of current density and current collector thickness. Using operando scanning electron microscopy, an increase in the lithium particle density is observed with increasing current density at the Cu|Li 6.25 Al 0.25 La 3 Zr 2 O 12 interface. This observation is then applied to improve the area coverage of lithium by pulsed plating. It is also shown that thin current collectors ( d = 100 nm) are unsuited for RFCs, as lithium whiskers penetrate them, resulting in highly heterogeneous interfaces. This suggests the use of thicker metal layers (several µm) to mitigate whisker penetration and facilitate homogeneous lithium plating.

25 ENERGY STORAGE↗
DOE OSTI2022

Different interfacial reactivity of lithium metal chloride electrolytes with high voltage cathodes determines solid-state battery performance

A deep understanding of the interaction of the surface of cathode materials with solid electrolytes is crucial to design advanced solid-state batteries (SSBs). This is especially true for the new class of lithium metal chloride (Li-M-Cl) solid electrolytes which are receiving rapidly growing attention due to their very high oxidative stability (>4 V) in combination with good ionic conductivity that can enable long cell cycle life. While Li-M-Cl electrolytes typically contain resource-limited metals (M) such as indium or rare earths, work has focused on substituting M with more abundant elements such as zirconium. Via operando resistance measurements using intermittent current interruption we explore the dynamic evolution of the interphase at the surface of Ni-rich NCM85 or NCM111 cathode particles inside a working SSB with three different Li-(M 1 ,M 2 )-Cl catholytes (Li 3 InCl 6 , Li 2 Sc 1/3 In 1/3 Cl 4 and Li 5/2 Y 1/2 Zr 1/2 Cl 6 ) to reveal the impact of the cationic metal substitution on the interfacial chemistry. We show that the metal plays a critical role in determining high voltage stability, contrary to prior assumptions. Using a combination of cyclic voltammetry and ultraviolet photoelectron spectroscopy measurements of the electronic band structure to assess oxidative stability; coupled with DFT calculations and ToF-SIMS to evaluate products formed at the interface at different upper cutoff potentials and degrees of delithiation, we are able to differentiate between electrochemical and chemical degradation. We find that Li 2 Sc 1/3 In 1/3 Cl 4 yields the highest (and Li 3 InCl 6 the lowest) stability against electrochemical oxidation, while Li 5/2 Y 1/2 Zr 1/2 Cl 6 undergoes a detrimental chemical reaction with oxygen released from Ni-rich NCM85 at high potentials, resulting in fast capacity fading. Altogether, our work establishes a platform for the metrics and an approach that can be utilized to efficiently evaluate the stability of new halide SEs in SSB cells.

25 ENERGY STORAGE↗
DOE OSTI2022

Increasing the Pressure‐Free Stripping Capacity of the Lithium Metal Anode in Solid‐State‐Batteries by Carbon Nanotubes

Abstract Lithium metal is the key anode material for solid‐state‐batteries as its successful implementation will drastically increase their energy and power densities. However, anode contact loss during stripping leads to dendrites upon plating and subsequent cell failure. Design strategies to mitigate these issues are crucial to enable the use of lithium metal anodes. This paper reports the dissolution kinetics of composite anodes made of lithium metal and carbon nanotubes (CNTs) with a garnet‐type solid electrolyte (SE). In addition to an enhancement of the effective diffusion within the anode, its dissolution is fundamentally changed from being 2D to 3D. By maintaining contact with the SE, the CNTs facilitate lithium transport to the interface, which yields more than 20 mAh cm −2 discharge capacity at 100 µ A cm −2 without the application of external stack pressure ( > 1 MPa). Conclusions drawn from electrochemical data on the anode microstructure are validated using cryo‐focused‐ion‐beam scanning electron microscopy and correlated with the mechanical properties. Micro‐indentation, acoustic analysis, and stress–strain testing show that mechanical properties of the anode, like yield strength and hardness, are adjustable. Overall, it is shown that the mechanical and electrochemical properties of Li–CNT composite electrodes can be tailored to suit the requirements of a practical cell.

Fuchs, Till↗
DOE OSTI2022

High areal capacity, long cycle life 4 V ceramic all-solid-state Li-ion batteries enabled by chloride solid electrolytes

All-solid-state Li batteries (ASSBs) employing inorganic solid electrolytes offer improved safety and are exciting candidates for next-generation energy storage. Herein, we report a family of lithium mixed-metal chlorospinels, Li 2 In x Sc 0.666-x Cl 4 (0 ≤ x ≤ 0.666), with high ionic conductivity (up to 2.0 mS cm -1 ) owing to a highly disordered Li-ion distribution, and low electronic conductivity (4.7 × 10-10 S cm -1 ), which are implemented for high-performance ASSBs. Owing to the excellent interfacial stability of the SE against uncoated high-voltage cathode materials, ASSBs utilizing LiCoO 2 or LiNi 0.85 Co 0.1 Mn 0.05 O 2 exhibit superior rate capability and long-term cycling (up to 4.8 V versus Li+/Li) compared to state-of-the-art ASSBs. In particular, the ASSB with LiNi 0.85 Co 0.1 Mn 0.05 O 2 exhibits a long life of >3,000 cycles with 80% capacity retention at room temperature. Additionally, high cathode loadings are also demonstrated in ASSBs with stable capacity retention of >4 mAh cm -2 (~190 mAh g -1 ).

25 ENERGY STORAGE↗
DOE OSTI2021

Working Principle of an Ionic Liquid Interlayer During Pressureless Lithium Stripping on Li 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO) Garnet‐Type Solid Electrolyte

Abstract Solid‐state‐batteries employing lithium metal anodes promise high theoretical energy and power densities. However, morphological instability occurring at the lithium/solid–electrolyte interface when stripping and plating lithium during cell cycling needs to be mitigated. Vacancy diffusion in lithium metal is not sufficiently fast to prevent pore formation at the interface above a certain current density during stripping. Applied pressure of several MPa can prevent pore formation, but this is not conducive to practical application. This work investigates the concept of ionic liquids as “self‐adjusting” interlayers to compensate morphological changes of the lithium anode while avoiding the use of external pressure. A clear improvement of the lithium dissolution process is observed as it is possible to continuously strip more than 70 μm lithium (i. e., 15 mAh cm −2 charge) without the need for external pressure during assembly and electrochemical testing of the system. The impedance of the investigated electrodes is analyzed in detail, and contributions of the different interfaces are evaluated. The conclusions are corroborated with morphology studies using cryo‐FIB‐SEM and chemical analysis using XPS. This improves the understanding of the impedance response and lithium stripping in electrodes employing liquid interlayers, acting as a stepping‐stone for future optimization.

Fuchs, Till↗
DOE OSTI2020

Kinetic versus Thermodynamic Stability of LLZO in Contact with Lithium Metal

Li 7 La 3 Zr 2 O 12 (LLZO) garnet-based oxides are a promising class of solid electrolytes used as the separator in all-solid-state batteries (ASSBs). While LLZO is considered to have a wide electrochemical stability window, its intrinsic stability in contact with lithium metal is not sufficiently well understood, and there is still a debate on the key question of whether LLZO does or does not form passivation layers before and during cycling. Utilizing both in situ and operando X-ray photoelectron spectroscopy techniques, in this work we reveal the presence of a kinetic barrier to the reduction of LLZO by Li metal, with the extent of oxygen-deficient interphase (ODI) formation depending sensitively on the energetics of Li metal arriving at the Li vertical bar LLZO interface. Despite the clear presence of a kinetic barrier to reduction, the electrochemical response of the Li vertical bar LLZO interface is unchanged by the presence of the ODI, indicating that ODI formation during electrochemical cycling does not hinder charge transfer across the Li vertical bar LLZO interface. Overall, these results reveal that the reactivity of LLZO with Li metal depends not only on the material properties of the adjoining phases (i.e., surface purity and active contact) and their resulting thermodynamic stability but also on the energy input at the interface and the resulting reaction kinetics. Furthermore, the presence of a kinetic barrier to reduction highlights the additional complexities governing the reactivity of solid-state interfaces in ASSBs and underscores the importance of operando characterization of interfacial stability to design more robust, high-performance protection strategies for solid electrolytes in contact with reactive electrodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Incorporating Diamondoids as Electrolyte Additive in the Sodium Metal Anode to Mitigate Dendrite Growth

Abstract Owing to the high abundance and gravimetric capacity (1165.78 mAh g −1 ) of pure sodium, it is considered as a promising candidate for the anode of next‐generation batteries. However, one major challenge needs to be solved before commercializing the sodium metal anode: The growth of dendrites during metal plating. One possibility to address this challenge is to use additives in the electrolyte to form a protective solid electrolyte interphase on the anode surface. In this work, we introduce a diamondoid‐based additive, which is incorporated into the anode to target this problem. Combining operando and ex situ experiments (electrochemical impedance spectroscopy, optical characterization, and cycling experiments), we show that molecular diamondoids are incorporated into the anode during cycling and successfully mitigate the growth of dendrites. Furthermore, we demonstrate the positive effect of the additive on the operation of sodium‐oxygen batteries by means of increased energy density.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗