Engineering Papers⌕ Search

Engineering topics

Jacob Putnam

Publications and source records attributed to Jacob Putnam.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Crashworthiness of a Lift Plus Cruise eVTOL Vehicle Design within Dynamic Loading Environments

To aid in the development of electric Vertical Take-off and Landing (eVTOL) technology, the National Aeronautics and Space Administration has undertaken research initiatives to evaluate and optimize design features of eVTOL aircraft. One such initiative has been to develop energy attenuating design mechanisms to improve eVTOL vehicle crashworthiness. In this study, crashworthiness design mechanisms, implemented within a six-passenger lift plus cruise (LPC) eVTOL concept vehicle, were evaluated under multi-axis dynamic loading conditions. This work builds upon crashworthiness design concepts previously optimized within a simplified vehicle-loading environment. The results of this study found the effectiveness of energy attenuating design mechanisms to be dependent on the complexity of load environment in which they were employed. An increase in off-axis loading resulted in a decrease in occupant protective capability. These results indicate the necessity for evaluating vehicle design across the range of possible dynamic impact conditions to characterize crashworthiness. This work provides preliminary methodology for implementing energy attenuating design mechanisms and evaluating crashworthiness for future UAM markets.

Jacob Putnam↗
NASA NTRSDate not supplied

Simulation of Lift plus Cruise Vehicle Models to Define a Full-Scale Crash Test Campaign

A series of dynamic simulations were completed on the National Aeronautics and Space Administration(NASA) Lift plus Cruise (LPC) concept electric Vertical Take-off and Landing (eVTOL) vehicle in preparation for an anticipated future full-scale crash-test campaign. The crash test campaign is envisioned as a data gathering exercise with an intent generating full-scale test data to inform eVTOL crashworthiness regulations, evaluate the use of energy absorbing concepts within vehicle design, and validate finite element modeling techniques used in crashworthiness predictions. This report discusses the two main objectives for the simulation efforts: the development of a structural cabin section, and a series of analyses utilized to determine the sensitivities of impact variables. A structural cabin section was created based from previous research efforts involving the LPC vehicle utilized for occupant response. To refine for the structural modifications, the wing and tail sections of the vehicle were removed. The tail was replaced with a representative mass at the aft of the fuselage. The overhead wing was replaced with a beam structure sized to approximate the bending response of the wing under crash loading conditions. The beam structure was fixed to the fuselage similar to the original Wingbox design in order to properly capture effects of this overhead mass on survivable volume within the vehicle. The fidelity of the fuselage frame structure within the FEM was increased to quantify the effect of frame sizing on structural response. From this an eVTOL test article design was developed, which satisfied basic crashworthiness requirements, was reconfigurable to assess the effect of various design avenues on structural response and optimized to improve manufacturability. The impact variable sensitivity results primarily show the orientation of the impact vector played a major role in types of injuries sustained, along with their severity. The vehicle was largely insensitive to small variations in pitch attitude but highly sensitive to both impact surface at certain angles and landing gear location.

eVTOL↗
NASA NTRSDate not supplied

Development and Analysis of Energy Absorbing Subfloor Concepts to Improve eVTOL Crashworthiness

To help ensure safe transportation within electric Vertical Take-off and Landing (eVTOL) vehicles the National Aeronautics and Space Administration (NASA) has been developing novel energy absorbing (EA) design technologies to improve crashworthiness within the unique design constraints of these vehicles. As part of this effort, a series of lightweight energy absorbing subfloor concepts were developed for potential use within eVTOL vehicle design. The capability of the subfloor designs was first evaluated through finite element (FE) model simulation in both component and vehicle level impact conditions. Knowledge gained from these analyses were used to iterate upon the design prior to fabrication. Fabrication and testing of the subfloor designs has begun and will be used to verify predicted capability. Results from FE model analysis was used to down select to a final subfloor geometry for additional component level optimization and full-scale test validation.

eVTOL↗
NASA NTRSDate not supplied

Study of Aircraft Structural Response and Occupant Loading During a Ditching Event Utilizing LS-DYNA Simulation

In this study, the capability of finite element model (FEM) analysis to assess aircraft structural response and occupant injury risk during aircraft water ditching conditions was evaluated. A FEM of the Fokker F28 aircraft, previously validated against full-scale crash test data, was simulated in a realistic water impact environment utilizing recorded conditions from the ditching of US Airways Flight 1549 into the Hudson River. The FEM of the F28 aircraft, was developed from a NASTRAN loads model provided by the vehicle manufacturer, calibrated using component fuselage drop-tests, and validated through test-analysis comparisons from a full-scale crash test of the F28 onto soil. Simulation results are presented in several categories: vehicle kinematics, structural accelerations, damage, occupant responses, and injury risk predictions. Results were consistent with the general outcomes of Flight 1549, indicating that the developed vehicle FEM, validated against land impact test data, may provide an effective tool for evaluating water ditching events.

Jacob Putnam↗
NASA NTRSDate not supplied

Development of Energy Absorbing Subfloor Concepts to Improve Crashworthiness of eVTOL Aircraft

To help ensure safe transportation within electric Vertical Take-off and Landing (eVTOL) vehicles the National Aeronautics and Space Administration (NASA) has been developing novel energy absorbing (EA) design technologies to improve crashworthiness within the unique design constraints of these vehicles. As part of this effort, a series of lightweight energy absorbing subfloor concepts were developed for potential use within eVTOL vehicle design. The capability of the subfloor designs was first evaluated through finite element (FE) model simulation in both component and vehicle level impact conditions. Knowledge gained from these analyses were used to iterate upon the design prior to fabrication. Fabrication and testing of the subfloor designs has begun and will be used to verify predicted capability. Results from FE model analysis was used to down select to a final subfloor geometry for additional component level optimization and full-scale test validation.

Crashworthiness↗
NASA NTRSDate not supplied

A Comparative Analysis of Occupant Response Between Component and Full Vehicle Tests of Fokker F28 Aircraft Hardware

In 2019, the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) conducted a full-scale crash test of a Fokker F28 MK1000 aircraft. This test concluded a multi-year research effort in which two component fuselage sections of a matching Fokker F28 aircraft were previously tested under similar vertical impact conditions. Due to facility and cost constraints of full-scale testing, aircraft are typically evaluated through component level tests (i.e. vertical drops of fuselage subsections or isolated seat tests). Although more practical, these tests are limited in their ability fully replicate the complex multi-axis loading environment induced on the occupants during a full-aircraft crash event. Because of this, there is risk that component level testing does not provide a complete assessment of vehicle crashworthiness. Comparative analysis between full-scale and component level testing of the Fokker F28 aircraft provides an excellent opportunity to evaluate differences in crashworthiness prediction made between these levels of test fidelity. In this study, Anthropomorphic Test Device (ATD, a.k.a crash test dummies) responses measured during the Fokker full scale impact test were compared to those measured in the component fuselage section drops. A variety of ATD configurations (5th, 50th, 95th) and positions (upright, braced) were tested in both the full-scale and component tests. ATD injury metric response comparisons were made across these ATD variations in addition to comparisons made with respect to ATD location within the vehicle. Results found the addition of horizontal impact velocity, achieved in the full-scale testing, along with aircraft structural effects altered ATD based crashworthiness assessment of the vehicle.

Crashworthiness↗
NASA NTRSDate not supplied

Soyuz Landing Reconstructions

Introduction: Recent data show a landing-attributed injury rate among Soyuz crew members to be higher than predicted in original certification analysis. New vehicles being developed for NASA are being certified using analytical tools to quantify injury risk. This assessment will provide data to allow the Agency to evaluate whether these tools are able to capture true injury risk and allow a comparison between Soyuz landings and upcoming vehicles. Methods: A finite element model (FEM) of the Soyuz descent module (DM) and its landing environment were developed to recreate Soyuz landing conditions. Occupant breakout models composed of the Soyuz seat and Sokol helmet were then developed to evaluate occupant response. These models included both anthropomorphic test device (ATD) and human body model (HBM) surrogates in three anthropometric sizes. A generalized distribution analysis of the Soyuz landing environment was performed using landing variable distributions from available literature. Results were used to identify trends in vehicle landing acceleration with landing conditions and to compare landing model injury risk predictions with those estimated in vehicle certification analysis. Next, historic Soyuz landings identified as inducing occupant injury during were reconstructed using the developed landing model and estimated landing conditions. Results and Discussion: This assessment demonstrated the capability of certification metrics, which include a combination of vehicle- and occupant-level injury risk analysis, to identify elevated injury risk landing conditions. However, the developed landing load predictions were limited by available vehicle and landing condition data. Additional data, particularly landing acceleration data specific to historic Soyuz landing conditions, would greatly enhance this assessment’s findings.

Preston Greenhalgh↗
NASA NTRSDate not supplied

A Summary of Test Results from a NASA Lift + Cruise eVTOL Crash Test

On November 9, 2022, the National Aeronautics and Space Administration (NASA) conducted a full-scale crash test of the NASA Lift+Cruise (LPC) reference vehicle at the NASA Langley Research Center Landing and Impact Research Facility (LandIR) under combined vertical and horizontal impact conditions to simulate a severe but survivable crash. The LPC test article is a carbon-composite skin/frame structure design, developed and fabricated for the cabin section only. The test utilized various configurations of seats and Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) intended to encompass a variety of occupant conditions. In addition, an in-house developed energy absorbing subfloor was utilized for the evaluation of load attenuation. Overhead mass was simulated using attached lifting hardware and other systems were simulated using ballast mass. The test article impacted the ground with velocities of 38.1 ft/s horizontal and 31.4 ft/s vertical. During the first approximately 38 milliseconds (ms), the cabin section experienced a large amount of acceleration on the belly which was attenuated by the subfloor structures and seats. Over the next approximately 160 ms, the test article experienced failure in the a-, b- and c-pillars, leading to a partial collapse of the overhead structure. Test data was collected on the belly, floors, seats, overhead mass, and tail. In addition, there was high speed full-field digital image correlation analysis data collected on the port side skin surface. Collected ATD data showed that the ATDs seated in the energy absorbing seats experienced loads at limits below the those in current regulations. Even without an energy absorbing seat, the energy absorbing subfloors crushed as intended, and limited the load on the large 95 th percentile ATD to 10% over suggested limits. The collapse of the roof did affect the 95 th percentile ATD, which showed high neck loading values due to head contact, whereas survivable volume was maintained for the other ATDs. While the energy absorbing subfloor and energy absorbing seats both contributed to occupant load attenuation, further optimization is suggested to increase their robustness.

evtol↗
NASA NTRSDate not supplied

Simulation and Analysis of NASA Lift Plus Cruise eVTOL Crash Test

The National Aeronautics and Space Administration (NASA) will perform a full-scale crash test of a representative electric vertical take-off and landing (eVTOL) fuselage in November 2022. The test article is a carbon-composite fuselage cabin section of the six-passenger lift plus cruise (LPC) eVTOL design concept which was created by NASA to advance understanding of eVTOL propulsion, noise, and safety. The test will consist of impacting the fuselage cabin section onto a concrete surface with a combined horizontal and vertical velocity approximating a severe but survivable crash landing for this vehicle design. Data generated from this test will be used to inform eVTOL crashworthiness regulation development, evaluate the use of energy absorbing concepts within vehicle design, and validate finite element model (FEM) techniques used in crashworthiness predictions. The cabin section response will be evaluated using structural instrumentation, anthropometric test devices (ATDs), and high-speed photogrammetry. This study will compare pre-test FEM predictions to test results to quantify the capability of these tools to predict crashworthiness of the carbon-composite eVTOL airframe.

Crashworthiness↗
NASA NTRSDate not supplied

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗
NASA NTRSDate not supplied

A Summary of Test Results from a NASA Lift + Cruise eVTOL Crash Test

On November 9, 2022, the National Aeronautics and Space Administration (NASA) conducted a full-scale crash test of the NASA Lift+Cruise (LPC) reference vehicle at the NASA Langley Research Center Landing and Impact Research Facility (LandIR) under combined vertical and horizontal impact conditions to simulate a severe but survivable crash. The LPC test article is a carbon-composite skin/frame structure design, developed and fabricated for the cabin section only. The test utilized various configurations of seats and Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) intended to encompass a variety of occupant conditions. In addition, an in-house developed energy absorbing subfloor was utilized for the evaluation of load attenuation. Overhead mass was simulated using attached lifting hardware and other systems were simulated using ballast mass. The test article impacted the ground with velocities of 38.1 ft/s horizontal and 31.4 ft/s vertical. During the first approximately 38 milliseconds (ms), the cabin section experienced a large amount of acceleration on the belly which was attenuated by the subfloor structures and seats. Over the next approximately 160 ms, the test article experienced failure in the a-, b- and c-pillars, leading to a partial collapse of the overhead structure. Test data was collected on the belly, floors, seats, overhead mass, and tail. In addition, there was high speed full-field digital image correlation analysis data collected on the port side skin surface. Collected ATD data showed that the ATDs seated in the energy absorbing seats experienced loads at limits below the those in current regulations. Even without an energy absorbing seat, the energy absorbing subfloors crushed as intended, and limited the load on the large 95 th percentile ATD to 10% over suggested limits. The collapse of the roof did affect the 95 th percentile ATD, which showed high neck loading values due to head contact, whereas survivable volume was maintained for the other ATDs. While the energy absorbing subfloor and energy absorbing seats both contributed to occupant load attenuation, further optimization is suggested to increase their robustness.

evtol↗
NASA NTRSDate not supplied

Simulation and Analysis of NASA Lift Plus Cruise eVTOL Crash Test

The National Aeronautics and Space Administration (NASA) will perform a full-scale crash test of a representative electric vertical take-off and landing (eVTOL) fuselage in November 2022. The test article is a carbon-composite fuselage cabin section of the six-passenger lift plus cruise (LPC) eVTOL design concept which was created by NASA to advance understanding of eVTOL propulsion, noise, and safety. The test will consist of impacting the fuselage cabin section onto a concrete surface with a combined horizontal and vertical velocity approximating a severe but survivable crash landing for this vehicle design. Data generated from this test will be used to inform eVTOL crashworthiness regulation development, evaluate the use of energy absorbing concepts within vehicle design, and validate finite element model (FEM) techniques used in crashworthiness predictions. The cabin section response will be evaluated using structural instrumentation, anthropometric test devices (ATDs), and high-speed photogrammetry. This study will compare pre-test FEM predictions to test results to quantify the capability of these tools to predict crashworthiness of the carbon-composite eVTOL airframe.

Crashworthiness↗
NASA NTRSDate not supplied

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗
NASA NTRSDate not supplied

An Overview of the NASA Lift+Cruise eVTOL Crash Test

Introduction – NASA RVLT Project Impact Dynamics / Crash Safety Task - Task Objective: “To improve the crashworthiness and impact safety of Urban Air Mobility (UAM) vehicle and provide data to simplify the certification process. Efforts will include development of validated computational models of these vehicles, as well as other impacting bodies such as birds and drones. Efforts will also focus on developing and evaluating energy absorbing and crush properties of emerging and non-traditional composite materials and processes. Finally, occupant protection will be addressed using computational models and physical assets as it pertains to all rotorcraft environments.” - Problem Statement: “There currently is a lack of data for requirements regarding the crashworthy performance of UAM vehicles and impact loads generated by a bird strike. To address this technology gap, NASA will develop test guidelines, adopt modeling methodologies demonstrating capability for ‘certification by analysis’, acquire vehicle and occupant data on full-scale representative vehicles, and provide data/guidance to consensus standards organizations and the UAM community.” - 4 Main focus points - The investigation of occupant injury using physical and computational assets - The development of energy absorbing technology - The generation of data from sub- and full-scale crash test data - The execution of advanced finite element modelling techniques

evtol↗