Engineering topics

Jackson, I.

Publications and source records attributed to Jackson, I..

4 records

NASA NTRS2019

The Influence of Redox Conditions on the Seismic Properties of Polycrystalline Olivine

Eight olivine specimens were fabricated by use of a solgel method and hot-pressing at 1200 degrees Centigrade and 300 megapascals (MPa) inside of welded Pt capsules. Each hot-pressed specimen was then recovered, precision ground, and wrapped in Pt, Ni or NiFe foil to vary oxygen fugacity (fO2) during the subsequent forced torsional oscillation measurements. Mechanical testing was conducted at 10 oscillation periods between 1 and 1000 seconds, at a confining pressure of 200 MPa, during a slow staged-cooling from a maximum temperature of 1200 degrees Centigrade down to room temperature. After mechanical testing, each specimen was axially sectioned and EBSD (Electron BackScatter Diffraction) was used for the determination of the representative grain size, and grain size distribution of each sample. In addition, each longitudinal section was mapped via FTIR (Fourier Transform Infrared Spectroscopy) to determine the spatial distribution and concentrations of chemically bound and molecular water. Amongst these eight specimens, chemically bound ‘water’ contents were observed to vary between 0 and 1150 atom parts per million (ppm) H/Si, and molecular water concentrations varied between 0 and 245 atom ppm H/Si. Our forced-oscillation results demonstrate that the measured magnitude of anelastic relaxation within the experimental ‘window’ of oscillation periods is unrelated to the water content. Rather, a relationship was observed between the magnitude of anelastic relaxation and the prevailing redox conditions, which is influenced by the choice of metal sleeving used during the mechanical test. Further, regardless of water content or metal sleeving, each specimen exhibits coupled variations in shear modulus and dissipation within the observational window, indicative of ‘high-temperature background’ behavior, that can be described by a Burgers-type model. During initial fitting of the Burgers models, the unrelaxed shear modulus at a reference temperature of 900°C (elastic unloading/reloading shear modulus G (sub UR)) and the temperature derivative of the unrelaxed shear modulus (dGU/dT), were treated as adjustable parameters. For all Fe-bearing olivine samples we observe deficits of G (sub UR) and increased values of dGU/dT, relative to the expected elastic (anharmonic) behavior for Fo (Forsterite content percentage) (sub 90) olivine. This behavior is indicative of anelastic relaxation occurring at shorter periods than observable within the ‘window’ of oscillation periods used in the mechanical test. Moving towards a comprehensive and seismologically applicable Burgers model, which includes this newly observed effect of redox conditions on anelastic relaxation, we will present our progress on reconciling truly anharmonic and elastic behavior of Fo (sub 90) olivine with our observed forced-oscillation data.

Cline, C. J., II↗

NASA NTRS2019

The Effect of Redox Conditions on Seismic Waves in Iron-Bearing Olivine: Implications for Understanding Planetary Interiros Through Seismilogy

Seismic data, inclusive of velocities and attenuation, can be utilized to elucidate the physical state of planetary interiors]. However, numerous micromechanical factors have been either experimentally demonstrated, or theoretically considered, to affect the propagation and dissipation of seismic energy within crystalline solids - including, but not limited to, changes in grain size, temperature, melt fraction, pressure and dislocation density. Thus, observed variations in seismic wave speeds and attenuation may be used to ultimately ‘map’ variations in physical properties, such as those listed above, within planetary bodies. But, in order to complete a successful inversion of seismic data into representations of physical properties, a first requirement is to obtain a fundamental laboratory based understanding of how each of these possible factors individually influences seismic waves. Here we conduct an experimental study with the initial objective to further understand one of the most commonly invoked, yet least studied, mechanisms that could alter intrinsic seismic wave attenuation: water content (occurring as chemically-bound hydroxyl). The historical basis for determining the effect of water on seismic properties was established predominantly through analogy with large-strain creep experiments conducted on olivine under water-saturated conditions. While these deformation experiments routinely demonstrate a weakening of olivine in the presence of water, they represent a fundamentally different deformation regime in comparison to the microstrains experienced due to a passing seismic wave. Thus, in order to directly assess the effects of water on seismic properties, small-strain experiments are required. Substantially modified seismic properties in the presence of water have been observed previously at low strains and low frequencies, but only in a single exploratory study conducted under water-saturated conditions. Thus, to properly test the theoretical predictions we conducted a systematic study of the seismic properties of olivine using low-frequency torsional oscillation on aggregates containing varying concentrations of bound hydroxyl, for the first time at under saturated conditions.

Cline, C. J., II↗

NASA NTRS1978

Streak camera time calibration procedures

Time calibration procedures for streak cameras utilizing a modulated laser beam are described. The time calibration determines a writing rate accuracy of 0.15% with a rotating mirror camera and 0.3% with an image converter camera.

Long, J.↗

NASA NTRS1977

Shock compression and adiabatic release of a titaniferous mare basalt

A report is presented regarding the dynamic properties of a rock indigenous to the mare basins of the moon. The reported data were obtained in a study of sample 70215, a very titanium-rich basalt (58% pyroxene, 18% ilmenite, 15% plagioclase, 6% olivine, and 3% quartz by weight). This rock is probably representative of a class of the earliest mare-filling extrusive rocks which are exposed on the present lunar surface. Two series of experiments were performed. One set of experiments involved the measuring of Hugoniot and release adiabats to 15.7 GPa with a propellant gun apparatus. In the second set of experiments, a light-gas gun was employed to yield Hugoniot data at about 120 GPa and release states at about 90 GPa. Lunar basalt 70215 appears to be among the densest rocks in the present lunar sample collection, having a crystal density of 3.38 g/cu cm and a porosity of about 1.3%. The results of the experiments have important implications for both the degree of shock metamorphism expected for impact processes and the extent of ejecta transport on mare surfaces with high-titanium basalt composition.

Ahrens, T. J.↗