Engineering topics

Iwens, R. P.

Publications and source records attributed to Iwens, R. P..

9 records

NASA NTRS1988

An approach to optical structures control

The stabilization of a large, spaceborne Cassegrain telescope is examined. Modal gain factors and known characteristics of disturbances are used to determine which structural model affect line of sight (LOS) the most and are candidates for active control. THe approach is to: (1) actively control and maintain alignment of optical components; (2) place structural control actuators for optimum impact on the selected modes for active vibration control; and (3) feed back the best available estimate of LOS error for direct LOS control. Local analog loops are used for lower bandwidth control and multivariable digital control for lower bandwidth control. The control law is synthesized in the frequency domain using the characteristic gain approach. Robustness is measured by employing conicity, which is an outgrowth of the positivity approach to robust feedback system design. The feasibility of the design approach will be demonstrated by conducting a lab experiment on a structure similar to a scaled version of the telescope.

Iwens, R. P.↗

NASA NTRS1978

Earth viewing with a shuttleborne experiment pointing mount

The article considers the attitude determination and the control problems of the shuttleborne earth-viewing pointing mounts (EPMs). Per-axis pointing performance requirements are identified for troposphere/stratosphere pollution, tropical storm research, and urban air pollution. Ephemeris error contributions to earth pointing are discussed and candidate attitude reference systems are described. Primary interfaces between the orbiter flight control system, Spacelab, pallet-mounted EPM, and control subsystems are outlined. A block diagram is given of the EPM-mounted stellar-inertial attitude reference system. The system's performance is evaluated on the basis of the inertial sensor and a three-axis covariance analysis.

Iwens, R. P.↗

NASA NTRS1977

Discrete time domain modelling and analysis of dc-dc converters with continuous and discontinuous inductor current

Using discrete time state variable representation, a generalized computer-aided modeling and analysis of dc-dc converters is presented. The methodology provides exact modeling and is applicable to all types of power stages and duty-cycle control, including continuous and discontinuous inductor current operation. Converter stability, transient behavior and audio susceptibility can be analytically evaluated and predicted. The generalized theory of the proposed approach to converter modeling and analysis is presented first, followed by a demonstrative example applying the theory to a constant frequency buck converter operating in continuous and discontinuous inductor current mode. Excellent agreement with laboratory test data has been observed.

Iwens, R. P.↗

NASA NTRS1977

Design study for LANDSAT-D attitude control system

The gimballed Ku-band antenna system for communication with TDRS was studied. By means of an error analysis it was demonstrated that the antenna cannot be open loop pointed to TDRS by an onboard programmer, but that an autotrack system was required. After some tradeoffs, a two-axis, azimuth-elevation type gimbal configuration was recommended for the antenna. It is shown that gimbal lock only occurs when LANDSAT-D is over water where a temporary loss of the communication link to TDRS is of no consequence. A preliminary gimbal control system design is also presented. A digital computer program was written that computes antenna gimbal angle profiles, assesses percent antenna beam interference with the solar array, and determines whether the spacecraft is over land or water, a lighted earth or a dark earth, and whether the spacecraft is in eclipse.

Iwens, R. P.↗

NASA NTRS1977

Generalized computer-aided discrete time domain modeling and analysis of dc-dc converters

A generalized discrete time domain modeling and analysis technique is presented for all types of switching regulators using any type of duty-cycle controller, and operating in both continuous and discontinuous inductor current. State space techniques are employed to derive an equivalent nonlinear discrete time model that describes the converter exactly. The system is linearized about its equilibrium state to obtain a linear discrete time model for small signal performance evaluations, such as stability, audiosusceptibility and transient response. The analysis makes extensive use of the digital computer as an analytical tool. It is universal, exact and easy to use.

Lee, F. C.↗

NASA NTRS1976

Design study for LANDSAT D attitude control system

A design and performance evaluation is presented for the LANDSAT D attitude control system (ACS). Control and configuration of the gimballed Ku-band antenna system for communication with the tracking and data relay satellite (TDRS). Control of the solar array drive considered part of the ACS is also addressed.

Iwens, R. P.↗

NASA NTRS1976

Severe storms observing satellite study

Payload distribution and the attitude control system for the multi-mission modular spacecraft/StormSat configuration are discussed. The design of the advanced atmospheric sounder and imaging radiometer (AASIR) gimbal drive and its servomechanism is described. Onboard data handling, data downlink communications, and ground data handling systems are developed. Additional topics covered include: magnetic unloading at synchronous altitude, north-south stationkeeping, and the feasibility and impact of flying the microwave atmospheric sounding radiometer (MASR) as an additional payload.

Iwens, R. P.↗

NASA NTRS1975

Time domain modelling and stability analysis of an integral pulse frequency modulated dc to dc power converter

Using state variable representation a nonlinear, discrete-time system is derived that models the converter exactly. This system is linearized about its steady state solution, and converter stability, transient response and audio susceptibility are studied. The steady state solution of the converter is stable if and only if all the roots of the linearized system are absolutely less than unity. Excellent agreement with laboratory test data has been observed.

Iwens, R. P.↗

NASA NTRS1972

Precision Pointing Control System (PPCS) system design and analysis

The precision pointing control system (PPCS) is an integrated system for precision attitude determination and orientation of gimbaled experiment platforms. The PPCS concept configures the system to perform orientation of up to six independent gimbaled experiment platforms to design goal accuracy of 0.001 degrees, and to operate in conjunction with a three-axis stabilized earth-oriented spacecraft in orbits ranging from low altitude (200-2500 n.m., sun synchronous) to 24 hour geosynchronous, with a design goal life of 3 to 5 years. The system comprises two complementary functions: (1) attitude determination where the attitude of a defined set of body-fixed reference axes is determined relative to a known set of reference axes fixed in inertial space; and (2) pointing control where gimbal orientation is controlled, open-loop (without use of payload error/feedback) with respect to a defined set of body-fixed reference axes to produce pointing to a desired target.

Frew, A. M.↗