Engineering topics

Ito, T. I.

Publications and source records attributed to Ito, T. I..

11 records

NASA NTRS1983

Thermal oxidative degradation reactions of linear perfluoroalkyl ethers

Thermal and thermal oxidative stability studies were performed on linear perfluoroalkyl ether fluids. The effect on degradation by metal catalysts and degradation inhibitors is reported. The linear perfluoroalkyl ethers are inherently unstable at 316 C in an oxidizing atmosphere. The metal catalysts greatly increased the rate of degradation in oxidizing atmospheres. In the presence of these metals in an oxidizing atmosphere, the degradation inhibitors were highly effective in arresting degradation at 288 C. However, the inhibitors had only limited effectiveness at 316 C. The metals promote degradation by chain scission. Based on elemental analysis and oxygen consumption data, the linear perfluoroalkyl ether fluids have a structural arrangement based on difluoroformyl and tetrafluoroethylene oxide units, with the former predominating. Previously announced in STAR as N82-26468

Jones, W. R., Jr.↗

NASA NTRS1982

Preparation of Perfluorinated Imidoylamidoxime Polymers

Perfluorinated imidoylamidoxime polymers with excellent resistance to heat, chemicals and solvents are prepared by condensing a perfluorinated nitrile with a perfluorinated amidoxime in vacuum or inert atmosphere from 20 degrees to 70 degrees C. When both reactants are difunctional, oligomeric or polymeric products are obtained. After cyclization of imidoylamidoxime groups to 1,2,4-oxadiazole linkages, process yields highly resistant elastomers. Competing side reactions are inhibited by low processing temperature.

Rosser, R. W.↗

NASA NTRS1982

Preparation of perfluorinated 1,2,4-oxadiazoles

Fluorinated alkyl or alkylether 1,2,4 oxadiazole compounds are prepared by cyclizing the corresponding alkyl or alkylether imidoyl amidoximes in vacuo or in an inert atmosphere at a temperature within the range of 40 C to 100 C. for a period of 8 to 144 hours in the presence of an acid compound which can accept ammonia to form a salt. The imidoyl amidoximes usable in this process are either polymeric or nonpolymeric. The products, when polymeric, have excellent heat, chemical and solvent resistance.

Kratzer, R. H.↗

NASA NTRS1982

Thermal oxidative degradation reactions of linear perfluoroalky lethers

Thermal and thermal oxidative stability studies were performed on linear perfluoro alkyl ether fluids. The effect on degradation by metal catalysts and degradation inhibitors are reported. The liner perfluoro alkylethers are inherently unstable at 316 C in an oxidizing atmosphere. The metal catalysts greatly increased the rate of degradation in oxidizing atmospheres. In the presence of these metals in an oxidizing atmosphere, the degradation inhibitors were highly effective in arresting degradation at 288 C. However, the inhibitors had only limited effectiveness at 316 C. The metals promote degradation by chain scission. Based on elemental analysis and oxygen consumption data, the linear perfluoro alkylether fluids have a structural arrangement based on difluoroformyl and tetrafluoroethylene oxide units, with the former predominating.

Jones, W. R., Jr.↗

NASA NTRS1981

Synthesis of perfluoroalkylene dianilines

The objective of this contrast was to optimize and scale-up the synthesis of 2,2-bis(4-aminophenyl)-hexafluoropropane and 1,3-bis(4-aminophenyl)hexafluoropropane, as well as to explore avenues to other perfluoroalkyl-bridged dianilines. Routes other than Friedel-Crafts reaction leading to 2,2-bis(4-aminophenyl)hexafluoropropane were investigated. The processes utilizing bisphenol-AF were all unsuccessful; reactions aimed at the production of 4-(hexafluoro-2-halo-isopropyl)aniline from the hydroxyl intermediate failed to yield the desired products. Tailoring the conditions of the Friedel-Crafts reaction of 4-(hexafluoro-2-hydroxyisopropyl)aniline, aniline, and aluminum chloride by using hydrochloride salts and selecting optimum reagent ratios, reaction times, and temperature resulted in approx. 20% yield of pure crystallized 2,2-bis(4-aminophenyl)hexafluoropropane in 0.2 mole reaction batches. Yields up to approx. 40% were realized in small, approx. 0.01 mole, batches. The synthesis of 1,3-bis(4-aminophenyl)hexafluoropropane starting with perfluoroglutarimidine was reinvestigated. The yield of the 4-step reaction sequence giving 1,3-bis(4-acetamidophenyl)hexafluoropropane was raised to 44%. The yield of the subsequent hydrolysis process was improved by a factor of approx. 2. Approaches to prepare other perfluoroalkyl-bridged dianilines were unsuccessful. Reactions reported to proceed readily with trifluoromethyl substituents failed when longer chain perfluoroalkyl groups were employed.

Paciorek, K. L.↗

NASA NTRS1981

Thermal oxidative degradation reactions of perfluoroalkylethers

The mechanisms operative in thermal oxidative degradation of Fomblin Z and hexafluoropropene oxide derived fluids and the effect of alloys and additives upon these processes are investigated. The nature of arrangements responsible for the inherent thermal oxidative instability of the Fomblin Z fluids is not established. It was determined that this behavior is not associated with hydrogen end groups or peroxy linkages. The degradation rate of these fluids at elevated temperatures in oxidizing atmospheres is dependent on the surface/volume ratio. Once a limiting ratio is reached, a steady rate appears to be attained. Based on elemental analysis and oxygen consumption data, CF2OCF2CF2O2, no. CF2CF2O, is one of the major arrangements present. The action of the M-50 and Ti(4 Al, 4 Mn) alloys is much more drastic in the case of Fomblin Z fluids than that observed for the hexafluoropropene derived materials. The effectiveness of antioxidation anticorrosion additives, P-3 and phospha-s-triazine, in the presence of metal alloys is very limited at 316 C; at 288 C the additives arrested almost completely the fluid degradation. The phospha-s-triazine appears to be at least twice as effective as the P-3 compound; it also protected the coupon better. The Ti(4 Al, 4 Mn) alloy degraded the fluid mainly by chain scission processes this takes place to a much lesser degree with M-50.

Paciorek, K. L.↗

NASA NTRS1980

Phosphazene diamines

The synthesis of a specific phosphazene diamine was optimized, other phosphorus-containing diamines were prepared, and their effect upon certain characteristics of epoxy resins, prepared via reaction with MY 720, in particular, char yield at elevated temperatures was evaluated. The synthesis of the phosphazene diamine resulting from the interaction of methylenedianline with 4,4'-bis(diphenylphosphino)biphenyl was simplified into a one step process giving 77 percent yield of the pure product. Using this procedure, a related diamine containing bis(diphenylphosphino)methane was obtained in a 70 percent yield. Preparation of another class of phosphorus containing amines based upon p-aminophenyldiphenyl-phosphine was unsuccessful; the inability to produce p-aminophenylithlum was responsible for this failure. Seven epoxy resins employing Araldite MY 720, diaminodiphenylsulfone, and two of the phosphorus containing diamines were prepared, characterized, and their char yield capacity at elevated temperatures assessed. Based on these investigations, the resins containing phosphorus appear to exhibit significantly better char formation characteristics than materials hardened using conventional amines, without impairing the other properties measured.

Paciorek, K. L.↗

NASA NTRS1978

Preparation of linear hydroxy substituted polyphosphazenes

The synthesis of partially hydroxy-substituted phosphazene prepolymers amenable to processing into cellular, flexible polyurethane foams was investigated. Factors determined include (1) the environment of the hydroxyl group; (2) the ease of the hexachlorocyclotriphosphazene polymerization; (3) the nature of the nonreactive substituents; and (4) the mode of introduction of the hydroxyl entity. The specific approaches taken, the rationale of the selections made, and the results are discussed.

Paciorek, K. L.↗

NASA NTRS1978

Synthesis of perfluoroalkylene aromatic diamines

Analogues of methylene dianilines were synthesized, in which the methylene group between the two aromatic nuclei was replaced by various perfluoroalkylene linkage. The hydrolytic thermal, and thermal oxidative stabilities of PMR Polyimides derived from these diamines were determined. Three types of PMR Polyimide discs were fabricated from the dimethyl ester of 3,3', 4,4'-benzophenonetetracarboxylic acid, the methyl ester of 5-norbornene-2,3-dicarboxylic acid, and one of the following three diamines: methyl dianiline, 1,3-bis(4-aminophenyl)hexafluoropropane, and 2,2-bis(4-aminophenyl)hexafluoropropane. The polyimide based on 2,2-bis(4-aminophenyl)hexafluoropropane exhibited the best hydrolytic, thermal, and thermal oxidative stability as determined by moisture uptake and thermogravimetric analysis.

Paciorek, K. L.↗

NASA NTRS1977

Cross Linking and Degradation Mechanisms in Model Sealant Candidates

Model compounds were investigated as to which type of heterocyclic ring is the most advantageous for curing sealants based on perfluoroalkylether chains. The relative thermal, thermal oxidative, hydrolytic, and fuel stability of potential crosslinks were determined. Specifically substituted materials were synthesized and evaluation of their stabilities in air, inert atmosphere, water, and Jet-A fuel at 235 and 325 C was made. Three heterocyclic ring systems were considered, namely, triazine, 1,2,4- and 1,3,4-oxadiazoles.

Paciorek, K. L.↗

NASA NTRS1977

Syntheses and Degradations of Fluorinated Heterocyclics: Perfluoroalkyl and Perfluoroalkylether-1,3,4-Oxadiazoles - 3

2,5-Bis(perfluoro-n-heptyl)-, 2-perfluoroalkylether-5-perfluoro-n- heptyl- , and 2 , 5-bisperfluoroalkylether-1,3,4-oxadiazoles were synthesized and characterized. 2,5-Bis(perfluoro-n-heptyl)-1,3,4-oxadiazole was thermally and hydrolytically stable at 325 C; however, in the presence of air, degradation took place at 235 C. The perfluoroalkylether analogue exhibited thermal and hydrolytic stability at 325 C; it was found to be unaffected by jet-A fuel and air at 235 C. At 325 C in air some degradation occurred as evidenced by volatiles production, oxygen consumption, and 96% starting material recovery.

Paciorek, K. J. L.↗