Engineering Papers⌕ Search

Engineering topics

Ilas, Germina

Publications and source records attributed to Ilas, Germina.

122 records · Page 7

On SCALE Validation for PBR Analysis

Studies were performed to assess the capabilities of the SCALE code system to provide accurate cross sections for analyses of pebble bed reactor configurations. The analyzed configurations are representative of fuel in the HTR-10 reactor in the first critical core and at full power operation conditions. Relevant parameters-multiplication constant, spectral indices, few-group cross sections-are calculated with SCALE for the considered configurations. The results are compared to results obtained with corresponding consistent MCNP models. The code-to-code comparison shows good agreement at both room and operating temperatures, indicating a good performance of SCALE for analysis of doubly heterogeneous fuel configurations. The development of advanced methods and computational tools for the analysis of pebble bed reactor (PBR) configurations has been a research area of renewed interest for the international community during recent decades. The PBR, which is a High Temperature Gas Cooled Reactor (HTGR) system, represents one of the potential candidates for future deployment throughout the world of reactor systems that would meet the increased requirements of efficiency, safety, and proliferation resistance and would support other applications such as hydrogen production or nuclear waste recycling. In the U.S, the pebble bed design is one of the two designs under consideration by the Next Generation Nuclear Plant (NGNP) Program.

08 HYDROGEN↗

SCALE 5.1 Predictions of PWR Spent Nuclear Fuel Isotopic Compositions

The purpose of this calculation report is to document the comparison to measurement of the isotopic concentrations for pressurized water reactor (PWR) spent nuclear fuel determined with the Standardized Computer Analysis for Licensing Evaluation (SCALE) 5.1 (Ref. ) epletion calculation method. Specifically, the depletion computer code and the cross-section library being evaluated are the twodimensional (2-D) transport and depletion module, TRITON/NEWT,2, 3 and the 44GROUPNDF5 (Ref. 4) cross-section library, respectively, in the SCALE .1 code system.

Radulescu, Georgeta↗

Design Study for a Low-Enriched Uranium Core for the High Flux Isotope Reactor, Annual report for FY 2009

This report documents progress made during FY 2009 in studies of converting the High Flux Isotope Reactor (HFIR) from high enriched uranium (HEU) fuel to low enriched uranium (LEU) fuel. Conversion from HEU to LEU will require a change in fuel form from uranium oxide to a uranium-molybdenum alloy. With axial and radial grading of the fuel foil and an increase in reactor power to 100 MW, calculations indicate that the HFIR can be operated with LEU fuel with no degradation in reactor performance from the current level. Results of selected benchmark studies imply that calculations of LEU performance are accurate. Studies are reported of the application of a silicon coating to surrogates for spheres of uranium-molybdenum alloy. A discussion of difficulties with preparing a fuel specification for the uranium-molybdenum alloy is provided. A description of the progress in developing a finite element thermal hydraulics model of the LEU core is provided.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Reference (Axially Graded) Low Enriched Uranium Fuel Design for the High Flux Isotope Reactor (HFIR)

During the past five years, staff at the Oak Ridge National Laboratory (ORNL) have studied the issue of whether the HFIR could be converted to low enriched uranium (LEU) fuel without degrading the performance of the reactor. Using state-of-the-art reactor physics methods and behind-the-state-of-the-art thermal hydraulics methods, the staff have developed fuel plate designs (HFIR uses two types of fuel plates) that are believed to meet physics and thermal hydraulic criteria provided the reactor power is increased from 85 to 100 MW. The paper will present a defense of the results by explaining the design and validation process. A discussion of the requirements for showing applicability of analyses to approval for loading the fuel to HFIR lead test core irradiation currently scheduled for 2016 will be provided. Finally, the potential benefits of upgrading thermal hydraulics methods will be discussed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Fuel Grading Study on a Low-Enriched Uranium Fuel Design for the High Flux Isotope Reactor

An engineering design study that would enable the conversion of the High Flux Isotope Reactor (HFIR) from high-enriched uranium to low-enriched uranium fuel is ongoing at Oak Ridge National Laboratory. The computational models used to search for a low-enriched uranium (LEU) fuel design that would meet the requirements for the conversion study, and the recent results obtained with these models during FY 2009, are documented and discussed in this report. Estimates of relevant reactor performance parameters for the LEU fuel core are presented and compared with the corresponding data for the currently operating high-enriched uranium fuel core. These studies indicate that the LEU fuel design would maintain the current performance of the HFIR with respect to the neutron flux to the central target region, reflector, and beam tube locations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

SCALE Validation Experience Using an Expanded Isotopic Assay Database for Spent Nuclear Fuel

The availability of measured isotopic assay data to validate computer code predictions of spent fuel compositions applied in burnup-credit criticality calculations is an essential component for bias and uncertainty determination in safety and licensing analyses. In recent years, as many countries move closer to implementing or expanding the use of burnup credit in criticality safety for licensing, there has been growing interest in acquiring additional high-quality assay data. The well-known open sources of assay data are viewed as potentially limiting for validating depletion calculations for burnup credit due to the relatively small number of isotopes measured (primarily actinides with relatively few fission products), sometimes large measurement uncertainties, incomplete documentation, and the limited burnup and enrichment range of the fuel samples. Oak Ridge National Laboratory (ORNL) recently initiated an extensive isotopic validation study that includes most of the public data archived in the Organization for Economic Cooperation and Development/Nuclear Energy Agency (OECD/NEA) electronic database, SFCOMPO, and new datasets obtained through participation in commercial experimental programs. To date, ORNL has analyzed approximately 120 different spent fuel samples from pressurized-water reactors that span a wide enrichment and burnup range and represent a broad class of assembly designs. The validation studies, completed using SCALE 5.1, are being used to support a technical basis for expanded implementation of burnup credit for spent fuel storage facilities, and other spent fuel analyses including radiation source term, dose assessment, decay heat, and waste repository safety analyses. This paper summarizes the isotopic assay data selected for this study, presents validation results obtained with SCALE 5.1, and discusses some of the challenges and experience associated with evaluating the results. Preliminary results obtained using SCALE 6 and ENDF/B-VII cross sections libraries are also briefly summarized. Oak Ridge National Laboratory (ORNL) has been performing spent-fuel isotopic validation studies using the depletion analysis methods in the SCALE [1] code system for the past 20 years. These studies involve comparisons of calculated inventories against measured isotopic composition data obtained from destructive radiochemical analysis of commercial spent nuclear fuel samples. The results of these benchmark studies are used to quantify the bias and uncertainties associated with isotopic calculations and ultimately determine appropriate margins for uncertainty that can be applied in safety-related analyses such as burnup credit in criticality calculations, decay heat analysis, and source terms. Previous studies using several versions of SCALE and nuclear data libraries have been published in multiple validation reports [2-6] that evaluate selected experimental data obtained largely from public sources. A study was recently initiated at ORNL with the objectives of updating and expanding the validation calculations using a comprehensive database of experimental isotopic assay data that includes isotopic composition data obtained from both publicly available sources and international commercial programs. As part of the study, an extensive isotopic database of nearly 120 measured spent fuel samples with an expanded range of initial enrichments and burnup values compared to previously analyzed data was reviewed and analyzed. The calculations were performed using two-dimensional (2-D) assembly models and a consistent set of modeling assumptions using the SCALE 5.1 code system and ENDF/B-V 44-group cross section library. As part of the current study, detailed benchmark modeling information and measurement data are being documented in a format that is readily usable for validating depletion and decay codes. The work is being extended to include analysis results using SCALE 6 and the ENDF/B-VII 238-group cross section library. This paper describes the isotopic composition data evaluated in this study and highlights the preliminary findings to date.

07 ISOTOPE AND RADIATION SOURCES↗

ENDF/B-VII Nuclear Data Libraries for SCALE-6.0

Version 6 of the SCALE (Standardized Computer Analyses for Licensing Evaluation) code system was released in February 2009. SCALE provides a comprehensive, integrated package of modular programs and nuclear data for a wide range of applications, including reactor physics, criticality safety, shielding, sensitivity/uncertainty analysis, and isotopic transmutation and radiation source term determination. SCALE computational modules are executed by automated control sequences that prepare input and call the desired modules in a particular order, linking output from one calculation to the next in series. The SCALE lattice physics sequence TRITON generates few-group, assembly-homogenized cross sections, as a function of burnup and branch states, which can be input to core simulator codes. TRITON couples the ORIGEN-S depletion module with either the NEWT (NEW Transport algorithm) twodimensional (2D) arbitrary-geometry transport code or the three-dimensional Monte Carlo KENO code. Fluxes from the transport solution, along with self-shielded multigroup (MG) cross sections, are passed to ORIGEN-S, which computes the time-dependent isotopic concentrations of more than 1400 nuclides. One of the major advancements in SCALE 6 is the availability of new nuclear data libraries based on ENDF/BVII for neutron transport calculations. In this paper we describe the SCALE ENDF/B-VII (designated here as V7) libraries and present some validation results for critical benchmarks and isotopic depletion experiments.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

ENDF/B-VII.0: Next Generation Evaluated Nuclear Data Library for Nuclear Science and Technology

Version 6 of the SCALE (Standardized Computer Analyses for Licensing Evaluation) code system was released in February 2009. SCALE provides a comprehensive, integrated package of modular programs and nuclear data for a wide range of applications, including reactor physics, criticality safety, shielding, sensitivity/uncertainty analysis, and isotopic transmutation and radiation source term determination. SCALE computational modules are executed by automated control sequences that prepare input and call the desired modules in a particular order, linking output from one calculation to the next in series. The SCALE lattice physics sequence TRITON generates few-group, assembly-homogenized cross sections, as a function of burnup and branch states, which can be input to core simulator codes. TRITON couples the ORIGEN-S depletion module with either the NEWT (NEW Transport algorithm) two-dimensional (2D) arbitrary-geometry transport code or the three-dimensional Monte Carlo KENO code. Fluxes from the transport solution, along with self-shielded multigroup (MG) cross sections, are passed to ORIGEN-S, which computes the time-dependent isotopic concentrations of more than 1400 nuclides. One of the major advancements in SCALE 6 is the availability of new nuclear data libraries based on ENDF/B-VII for neutron transport calculations. In this paper we describe the SCALE ENDF/B-VII (designated here as V7) libraries and present some validation results for critical benchmarks and isotopic depletion experiments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Design Study for a Low-Enriched Uranium Core for the High Flux Isotope Reactor, Annual Report for FY 2008

This report documents progress made during FY 2008 in studies of converting the High Flux Isotope Reactor (HFIR) from highly enriched uranium (HEU) fuel to low-enriched uranium (LEU) fuel. Conversion from HEU to LEU will require a change in fuel form from uranium oxide to a uranium-molybdenum alloy. With axial and radial grading of the fuel foil and an increase in reactor power to 100 MW, calculations indicate that the HFIR can be operated with LEU fuel with no degradation in reactor performance from the current level. Results of selected benchmark studies imply that calculations of LEU performance are accurate. Scoping experiments with various manufacturing methods for forming the LEU alloy profile are presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Designing a New Fuel for HFIR-Performance Parameters for LEU Core Configurations

An engineering design study for a fuel that would enable the conversion of the High Flux Isotope Reactor from highly enriched uranium to low enriched uranium fuel is ongoing as part of an effort sponsored by the U.S. Department of Energy's National Nuclear Security Administration through the Global Threat Reduction Initiative. Given the unique fuel and core design and high power density of the reactor and the requirement that the impact of the fuel change on the core performance and operation be minimal, this conversion study presents a complex and challenging task, requiring improvements in the computational models currently used to support the operation of the reactor and development of new models that would take advantage of newly available simulation methods and tools. The computational models used to search for a fuel design that would meet the requirements for the conversion study and the results obtained with these models are presented and discussed. Estimates of relevant reactor performance parameters for the low enriched uranium fuel core are presented and compared to the corresponding data for the currently operating highly enriched uranium fuel core.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗