Engineering Papers⌕ Search

Engineering topics

Ilas, Germina

Publications and source records attributed to Ilas, Germina.

At least 73 records · Page 4

Review of Experimental Assay Data for PWR Spent Fuel

The primary objective of this study is to review existing experimental assay data for pressurized water reactor (PWR) spent fuel, identify gaps in existing data, and asses the potential value of new isotopic measurements for nuclides relevant to burnup credit, shielding, and decay heat validation. The impact of adding new, high-quality experimental assay data on uncertainties associated with PWR depletion validation is discussed. In particular, the discussion focuses on potential benefits of additional isotopic measurements for spent fuel rods available at Oak Ridge National Laboratory. Selected measurements for these spent fuel rods are ongoing in Fiscal Year 2019 (FY19) as funded by the US Department of Energy (DOE) under the Spent Fuel and Waste Science and Technology (SFWST) Program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Neutronic and thermal-hydraulic feasibility studies for High Flux Isotope Reactor conversion to low-enriched uranium silicide dispersion fuel

An iterative design process involving neutronic and thermal-hydraulic modeling and simulation has been employed to assess the feasibility of converting the Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR) from high-enriched uranium (HEU) to low-enriched uranium (LEU) silicide dispersion fuel. ORNL is funded by the National Nuclear Security Administration to evaluate HFIR conversion. Previous HFIR conversion studies focused on U-10Mo monolithic fuel; however, due to potential fabrication issues with the complex HFIR U-10Mo fuel design, ORNL is evaluating U 3 Si 2 -Al dispersion fuel as an alternative LEU fuel system.Fueled by 10.1 kg of HEU and operated at 85 MW, HFIR provides one of the highest steady-state neutron fluxes of any research reactor in the world. Retrofitting a compact, high-power density, HEU-based core with LEU is a challenging problem to solve, especially when considering the conversion requirements. Neutronic and thermal-hydraulic analyses were performed with Shift and HSSHTC, respectively, to predict reactor performance and thermal safety margins. A number of designs were proposed and evaluated using an iterative approach in an effort to show that reactor performance could match that obtained using HEU fuel and that thermal safety margins were adequate. Furthermore this study concludes that conversion of HFIR with U 3 Si 2 -Al LEU fuel is feasible if, among other requirements, the fuel meat region is centered and symmetric about the fuel plate thickness centerline, the active fuel zone length is increased from 50.80 cm to 55.88 cm, the proposed fabrication tolerances can be met, and the fuel can be qualified for HFIR conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Neutronic and Thermal-Hydraulic Feasibility Studies for High Flux Isotope Reactor Conversion to Low-Enriched Uranium U3Si2-Al Fuel

Oak Ridge National Laboratory (ORNL) operates the High Flux Isotope Reactor (HFIR) for the US Department of Energy Office of Science to perform neutron scattering experiments, produce isotopes, and conduct materials irradiation research. ORNL is funded by the National Nuclear Security Administration (NNSA) Office of Materials Management and Minimization to evaluate the conversion of HFIR’s fuel from high-enriched uranium (HEU) to low-enriched (LEU). Due to potential fabrication issues with the complex UMo fuel design required to convert HFIR, NNSA requested ORNL to evaluate an alternate LEU fuel form – U3Si2-Al dispersion fuel. Neutronic and thermal-hydraulic feasibility analyses were performed with Shift and HSSHTC, respectively, to predict reactor performance and thermal safety margins. A number of designs were proposed and evaluated using an iterative approach in an effort to show that reactor performance could match that obtained using HEU fuel and that thermal safety margins were adequate. This study concludes that conversion of HFIR with U3Si2-Al LEU (19.75 wt.%) fuel with 4.8 gU/cm3 is feasible if, among other requirements, the fuel meat region is centered and symmetric about the fuel plate thickness centerline, the active fuel zone length is increased 5.08 cm to 55.88 cm, the proposed fabrication tolerances can be met, and the fuel can be qualified for HFIR conditions.

Chandler, David↗

Fiscal Year (FY) 2017 Activities for the Spent Fuel Nondestructive Assay Project

The main focus of research in the NA-241 spent fuel nondestructive assay (NDA) project in FY17 has been completing the fabrication and testing of two prototype instruments for upcoming spent fuel measurements at the Clab interim storage facility in Sweden. One is a passive instrument: Differential Die-away Self Interrogation-Passive Neutron Albedo Reactivity (DDSI), and one is an active instrument: Differential Die-Away-Californium Interrogation with Prompt Neutron (DDA). DDSI was fabricated and tested with fresh fuel at Los Alamos National Laboratory in FY15 and FY16, then shipped to Sweden at the beginning of FY17. Research was performed in FY17 to simplify results from the data acquisition system, which is complex because signals from 56 different 3He detectors must be processed using list mode data. The DDA instrument was fabricated at the end of FY16. New high count rate electronics better suited for a spent fuel environment (i.e., KM-200 preamplifiers) were built specifically for this instrument in FY17, and new Tygon tubing to house electrical cables was purchased and installed. Fresh fuel tests using the DDA instrument with numerous configurations of fuel rods containing depleted uranium (DU), low enriched uranium (LEU), and LEU with burnable poisons (Gd) were successfully performed and compared to simulations.1 Additionally, members of the spent fuel NDA project team travelled to Sweden for a “spent fuel characterization and decay heat” workshop involving simulations of spent fuel and analysis of uncertainties in decay heat calculations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Heat deposition analysis for the High Flux Isotope Reactor’s HEU and LEU core models

The High Flux Isotope Reactor at Oak Ridge National Laboratory is an 85 MW th pressurized light-water-cooled and -moderated flux-trap type research reactor. The reactor is used to conduct numerous experiments, advancing various scientific and engineering disciplines. As part of an ongoing program sponsored by the US Department of Energy National Nuclear Security Administration Office of Material Management and Minimization, studies are being performed to assess the feasibility of converting the reactor’s highly enriched uranium fuel to low-enriched uranium fuel. To support this conversion project, reference models with representative experiment target loading and explicit fuel plate representation were developed and benchmarked for both fuels to (1) allow for consistent comparison between designs for both fuel types and (2) assess the potential impact of low-enriched uranium conversion. These high-fidelity models were used to conduct heat deposition analyses at the beginning and end of the reactor cycle and are presented herein. This article (1) discusses the High Flux Isotope Reactor models developed to facilitate detailed heat deposition analyses of the reactor’s highly enriched and low-enriched uranium cores, (2) examines the computational approach for performing heat deposition analysis, which includes a discussion on the methodology for calculating the amount of energy released per fission, heating rates, power and volumetric heating rates, and (3) provides results calculated throughout various regions of the highly enriched and low-enriched uranium core at the beginning and end of the reactor cycle. These are the first detailed high-fidelity heat deposition analyses for the High Flux Isotope Reactor’s highly enriched and low-enriched core models with explicit fuel plate representation. Lastly, these analyses are used to compare heat distributions obtained for both fuel designs at the beginning and end of the reactor cycle, and they are essential for enabling comprehensive thermal hydraulics and safety analyses that require detailed estimates of the heat source within all of the reactor’s fuel element regions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The Impact of Operating Parameters and Correlated Parameters for Extended BWR Burnup Credit

Applicants for certificates of compliance for spent nuclear fuel (SNF) transportation and dry storage systems perform analyses to demonstrate that these systems are adequately subcritical per the requirements of Title 10 of the Code of Federal Regulations (10 CFR) Parts 71 and 72. For pressurized water reactor (PWR) SNF, these analyses may credit the reduction in assembly reactivity caused by depletion of fissile nuclides and buildup of neutron-absorbing nuclides during power operation. This credit for reactivity reduction during depletion is commonly referred to as burnup credit (BUC). US Nuclear Regulatory Commission (NRC) staff review BUC analyses according to the guidance in the Division of Spent Fuel Storage and Transportation Interim Staff Guidance (ISG) 8, Revision 3, Burnup Credit in the Criticality Safety Analyses of PWR Spent Fuel in Transportation and Storage Casks.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Decay heat uncertainty for BWR used fuel due to modeling and nuclear data uncertainties

Characterization of the energy released from radionuclide decay in nuclear fuel discharged from reactors is essential for the design, safety, and licensing analyses of used nuclear fuel storage, transportation, and repository systems. There are a limited number of decay heat measurements available for commercial used fuel applications. Because decay heat measurements can be expensive or impractical for covering the multitude of existing fuel designs, operating conditions, and specific application purposes, decay heat estimation relies heavily on computer code prediction. Uncertainty evaluation for calculated decay heat is an important aspect when assessing code prediction and a key factor supporting decision making for used fuel applications. While previous studies have largely focused on uncertainties in code predictions due to nuclear data uncertainties, this study discusses uncertainties in calculated decay heat due to uncertainties in assembly modeling parameters as well as in nuclear data. Capabilities in the SCALE nuclear analysis code system were used to quantify the effect on calculated decay heat of uncertainties in nuclear data and selected manufacturing and operation parameters for a typical boiling water reactor (BWR) fuel assembly. Furthermore, the BWR fuel assembly used as the reference case for this study was selected from a set of assemblies for which high-quality decay heat measurements are available, to assess the significance of the results through comparison with calculated and measured decay heat data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-Fidelity Modelng and Simulation for a High Flux Isotope Reactor Low-Enriched Uranium Core Design

A high-fidelity model of the High Flux Isotope Reactor (HFIR) with a low-enriched uranium (LEU) fuel design and a representative experiment loading has been developed to serve as a new reference model for LEU conversion studies. With the exception of the fuel elements, this HFIR LEU model is completely consistent with the current highly enriched uranium HFIR model. Results obtained with the new LEU model provide a baseline for analysis of alternate LEU fuel designs and further optimization studies. The newly developed HFIR LEU model has an explicit representation of the HFIR-specific involute fuel plate geometry, including the within-plate fuel meat contouring, and a detailed geometry model of the fuel element side plates. Such high-fidelity models are necessary to accurately account for the self-shielding from 238 U and the depletion of absorber materials present in the side plates. In addition, a method was developed to account for fuel swelling in the high-density LEU fuel plates during the depletion simulation. In conclusion, calculated time-dependent metrics for the HFIR LEU model include fission rate and cumulative fission density distributions, flux and reaction rates for relevant experiment locations, point kinetics data, and reactivity coefficients.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Impact of Reactor Operating Parameters on Cask Reactivity in BWR Burnup Credit

This paper discusses the effect of reactor operating parameters used in fuel depletion calculations onspent fuel cask reactivity, with relevance for boiling-water reactor (BWR) burnup credit (BUC)applications. Assessments that used generic BWR fuel assembly and spent fuel cask configurationsare presented. The considered operating parameters, which were independently varied in thedepletion simulations for the assembly, included fuel temperature, bypass water density, specificpower, and operating history. Different operating history scenarios were considered for the assemblydepletion to determine the effect of relative power distribution during the irradiation cycles, as wellas the downtime between cycles. Depletion, decay, and criticality simulations were performed usingcomputer codes and associated nuclear data within the SCALE code system. Results quantifying thedependence of cask reactivity on the assembly depletion parameters are presented herein.

Ilas, Germina↗

Key metrics for HFIR HEU and LEU models

This report compares key metrics for two fuel design models of the High Flux Isotope Reactor (HFIR). The first model represents the highly enriched uranium (HEU) fuel currently in use at HFIR, and the second model considers a low-enriched uranium (LEU) interim design fuel. Except for the fuel region, the two models are consistent, and both include an experiment loading that is representative of HFIR's current operation. The considered key metrics are the neutron flux at the cold source moderator vessel, the mass of 252 Cf produced in the flux trap target region as function of cycle time, the fast neutron flux at locations of interest for material irradiation experiments, and the reactor cycle length. These key metrics are a small subset of the overall HFIR performance and safety metrics. They were defined as a means of capturing data essential for HFIR's primary missions, for use in optimization studies assessing the impact of HFIR's conversion from HEU fuel to different types of LEU fuel designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Modeling and Depletion Simulations for a High Flux Isotope Reactor Cycle with a Representative Experiment Loading

The purpose of this report is to document a high-fidelity VESTA/MCNP High Flux Isotope Reactor (HFIR) core model that features a new, representative experiment loading. This model, which represents the current, high-enriched uranium fuel core, will serve as a reference for low-enriched uranium conversion studies, safety-basis calculations, and other research activities. A new experiment loading model was developed to better represent current, typical experiment loadings, in comparison to the experiment loading included in the model for Cycle 400 (operated in 2004). The new experiment loading model for the flux trap target region includes full length 252 Cf production targets, 75 Se production capsules, 63 Ni production capsules, a 188 W production capsule, and various materials irradiation targets. Fully loaded 238 Pu production targets are modeled in eleven vertical experiment facilities located in the beryllium reflector. Other changes compared to the Cycle 400 model are the high-fidelity modeling of the fuel element side plates and the material composition of the control elements. Results obtained from the depletion simulations with the new model are presented, with a focus on time-dependent isotopic composition of irradiated fuel and single cycle isotope production metrics.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

High Flux Isotope Reactor Core Analysis-Challenges and Recent Enhancements in Modeling and Simulation

A concerted effort over the past few years has focused on enhancing the core depletion models for the High Flux Isotope Reactor (HFIR) as part of a comprehensive study for designing a HFIR core that would use low-enriched uranium (LEU) fuel. A HFIR core depletion model that is based on current state-of-the-art methods and nuclear data was needed for use as a reference for the design of an LEU fuel for HFIR and to improve the basis for analyses that support HFIR’s current operation with high-enriched uranium (HEU) fuel. This paper summarizes the recent improvements in modeling and simulation for HFIR core analyses, with a focus on core depletion models.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗