Ihme, Matthias — Page 2 | Engineering Papers

DOE OSTI2023

Experimental and numerical investigation of flame stabilization and pollutant formation in matrix stabilized ammonia-hydrogen combustion

Ammonia (NH 3 ) is a carbon-free fuel that offers an attractive alternative for reducing greenhouse gas emissions. However, the slow flame speed, low heating value, and emissions of nitrogen-containing pollutants present significant issues for practical combustion applications. To address these issues, we investigate the use of matrix stabilized combustion. In this type of burner, combustion is performed within an inert porous ceramic foam, heat is recirculated by solid conduction and radiation, which enhances flame speed and combustion stabilization, thereby permitting combustion over a wide range of equivalence ratio conditions. We present a new porous media burner (PMB) capable of stabilizing NH 3 /air flames at ambient conditions. An extensive experimental characterization of the stability of this burner is conducted with up to 30% by volume of hydrogen (H 2 ) in the fuel stream. A 15:1 turndown ratio is demonstrated, with a high thermal power density of 62 MW m -3 . Concentrations of NO, unburnt NH 3 , and H 2 in the exhaust stream are measured. Two regimes are identified for low NO operation: rich and very lean. For rich conditions, NO emissions decrease with increasing equivalence ratio and decreasing H 2 blending. Unburnt NH 3 emissions follow opposite trends. These measurements are complemented by simulations in which the burner is represented by a coupled solid-gas reactor network. In conclusion, this model captures the burner’s pollutant emissions to good accuracy and is used to analyze the mechanisms of pollutant formation.

42 ENGINEERING↗

DOE OSTI2023

Corrosive Influence of Carbon Dioxide on Crack Initiation in Quartz: Comparison With Liquid Water and Vacuum Environments

The stimulation of crack growth in quartz and siliceous materials by injecting carbon dioxide (CO 2 ) represents a key technology in long-term carbon storage and in the development of natural gas wells. While this technology is widely used, the molecular impact of CO 2 interactions on the solid matrix is only incompletely understood. In this work, we employ reactive molecular dynamics simulations to study how the CO 2 fluid environment affects the mechanical properties of pre-cracked single-crystal quartz. The thermodynamic conditions of interest are those relevant to subsurface reservoirs. We report how structural properties of quartz—bond length distribution and crack tip shape—evolve upon introduction of a fluid. These properties are directly related to macroscopic quantities of the global stress-strain curves, thus reaffirming the inherent coupling across multiple scales for fluid-solid interactions in the subsurface. Here, we find that CO 2 reduces the fracture toughness of quartz by 12.1% compared to that of quartz in vacuum, thereby promoting crack growth and enhancing fluid transport in the subsurface.

58 GEOSCIENCES↗

DOE OSTI2023

Cost-constrained adaptive simulations of transient spray combustion in a gas turbine combustor

Predictive high-fidelity simulations of turbulent spray combustion must capture the combined effects of complex chemistry, multiphase evaporating flow and spray-flame interactions to achieve physical accuracy. Finite-rate chemistry (FRC) combined with a realistic chemical mechanism is a combustion model well-suited for this purpose, but has a high computational cost due to the large number and stiffness of transported chemical species. In contrast, flamelet-based models achieve lower cost by transporting a small number of quantities of reduced stiffness, but assumptions regarding local flame topology, boundary conditions and inter-phase coupling limit their physical accuracy. Recently, the Pareto-efficient combustion (PEC) framework was developed to dynamically assign combustion models based on local cost and accuracy metrics in gas-phase reacting flows. In this work, we extend this PEC framework to spray combustion through the rigorous analysis of the multiphase coupling terms in the governing equations. The derivation shows that spray evaporation causes errors in the prediction of species mass fractions for flamelet-based models due to the sensitivity of the local thermo-chemical state to changes in composition caused by fuel vaporization across combustion regimes present in practical spray combustion devices. Sub-model assignment is formulated as a multiple-choice knapsack problem, where computational cost is directly controlled through the fraction of the domain assigned to the FRC sub-model. The extended PEC formulation is applied to the simulation of a realistic rich-quench-lean gas turbine combustor at steady-state conditions, as well as transient operation resulting in lean blow-out (LBO). Analysis of transient simulations during LBO demonstrates the extended PEC formulation’s capacity to dynamically adapt to changing conditions within the combustor. Transient combustor dynamics are shown to approach convergence with limited increases in computational cost, while retaining substantial computational cost reduction compared to monolithic FRC simulations. Through PEC simulations with increasing fractions of the domain assigned to FRC, monolithic flamelet simulations are shown to over-predict flame stability during LBO. Finally, the extended PEC formulation is thus shown to overcome deficiencies of monolithic models by controlling modeling error for multiphase combustion modeling.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS2020

Modeling Heatshield Erosion due to Dust Particle Impacts for Martian Entries

Heatshield design for spacecraft entering the atmosphere of Mars may be affected by the presence of atmospheric dust. Particle impacts with sufficient kinetic energy can cause spallation damage to the heatshield that must be estimated. The dust environment in terms of particle size distribution and number density can be inferred from ground-based or atmospheric observations at Mars. Using a Lagrangian approach, the particle trajectories through the shock layer can be computed using a set of coupled ordinary differential equations. The dust particles are small enough that non-continuum effects must be accounted for when computing the drag coefficient and heat transfer to the particle surface. Surface damage correlations for impact crater diameter and penetration depth are presented for fused-silica, AVCOAT, Shuttle tiles, cork, and Norcoat Liège. The cork and Norcoat Liège correlations are new and were developed in this study. The modeling equations presented in this paper are applied to compute the heatshield erosion due to dust particle impacts on the ExoMars Schiaparelli entry capsule during dust storm conditions.

Palmer, Grant↗

NASA NTRS2020

Modeling Heatshield Erosion Due to Dust Particle Impacts for Martian Entries

Heatshield design for spacecraft entering the atmosphere of Mars may be affected by the presence of atmospheric dust. Particle impacts with sufficient kinetic energy can cause spallation damage to the heatshield that must be estimated. The dust environment in terms of particle size distribution and number density can be inferred from ground-based or atmospheric observations at Mars. Using a Lagrangian approach, the particle trajectories through the shock layer can be computed using a set of coupled ordinary differential equations. The dust particles are small enough that non-continuum effects must be accounted for when computing the drag coefficient and heat transfer to the particle surface. Surface damage correlations for impact crater diameter and penetration depth are presented for fused-silica, AVCOAT, Shuttle tiles, cork, and Norcoat Liège. The cork and Norcoat Liège correlations are new and were developed in this study. The modeling equations presented in this paper are applied to compute the heatshield erosion due to dust particle impacts on the ExoMars Schiaparelli entry capsule during dust storm conditions.

Palmer, Grant↗

NASA NTRS2019

Numerical Predictions of Dust-Induced Heat Flux Augmentation in Hypersonic Blunt-Body Flows Using a Discontinuous Galerkin Multiphase Flow Solver

Recent interest in human-scale missions to Mars has motivated the need for high-fidelity simulations of reentry flows. During a dust storm, there can be high levels of suspended dust in the Martian atmosphere, which cannot only enhance erosion of thermal protection systems but also transfer energy and momentum to the shock layer, thereby significantly augmenting the surface heat flux. Second-order finite-volume schemes are typically employed for hypersonic flow simulations, but such schemes suffer from a number of disadvantages. An attractive alternative is discontinuous Galerkin methods, which benefit from arbitrarily high spatial order of accuracy, geometric flexibility, and other properties. To enable accurate computations of high-speed particle-laden flows, an Euler-Lagrange methodology was developed in which the Eulerian field of the carrier gas is calculated using a discontinuous Galerkin scheme while the disperse phase is treated with Lagrangian particle tracking. We discuss challenges associated with coupling these two formulations and how to handle them. Momentum and energy transfer between the carrier gas and the particle phase is considered, and the importance of accounting for interparticle collisions is assessed. In addition, we describe the physical model of the particle phase and examine effects of its uncertainties on the numerical solution. We demonstrate the performance of the Euler-Lagrange method in representative testcases, with focus on the accurate prediction of particle trajectories and heating augmentation. Quantitative comparisons with experiments are provided.

Ching, Eric J.↗