Engineering Papers⌕ Search

Engineering topics

Ibrahim, S. R.

Publications and source records attributed to Ibrahim, S. R..

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Dynamic Identification for Control of Large Space Structures

This is a compilation of reports by the one author on one subject. It consists of the following five journal articles: (1) A Parametric Study of the Ibrahim Time Domain Modal Identification Algorithm; (2) Large Modal Survey Testing Using the Ibrahim Time Domain Identification Technique; (3) Computation of Normal Modes from Identified Complex Modes; (4) Dynamic Modeling of Structural from Measured Complex Modes; and (5) Time Domain Quasi-Linear Identification of Nonlinear Dynamic Systems.

Ibrahim, S. R.↗
NASA NTRS1985

A Parametric Study of the Ibrahim Time Domain Modal Identification Algorithm

The accuracy of the Ibrahim time Domain (ITD) identification algorithm in extracting structural model parameters from free response functions was studied using computer simulated data for 65 positions on an isotropic, uniform thickness plate with mode shapes obtained by NASTRAN analysis. Natural frequencies were used to study identification results over ranges of modal parameter values and user selectable algorithm constants. Effects of superimposing various levels of noise onto the functions were investigated. No detrimental effects were observed when the number of computational degrees of freedom allowed in the algorithm was made many times larger than the minimum necessary for adequate identification. The use of a high number of degrees of freedom when analyzing experimental data, for the simultaneous identification of many modes in one computer run are suggested.

Pappa, R. S.↗
NASA NTRS1985

Large Modal Survey Testing Using the Ibrahim Time Domain Identification Technique

The ability of the ITD identification algorithm in identifying a complete set of structural modal parameters using a large number of free-response time histories simultaneously in one analysis, assuming a math model with a high number of degrees-of-freedom, has been studied. Identification results using simulated free responses of a uniform rectangular plate, with 225 measurement stations, and experimental responses from a ground vibration test of the Long Duration Exposure Facility (LDEF) Space Shuttle payload, with 142 measurement stations, are presented. As many as 300 degrees-of-freedom were allowed in analyzing these data. In general, the use of a significantly oversized math model in the identification process was found to maintain or increase identification accuracy and to identify modes of low response level that are not identified with smaller math model sizes. The concept of a Mode Shape Correlation Constant is introduced for use when more than one identification analysis of the same structure are conducted. This constant quantifies the degree of correlation between any two sets of complex mode shapes identified using different excitation conditions, different user-selectable algorithm constants, or overlapping sets of measurements.

Ibrahim, S. R.↗
NASA NTRS1985

Computation of Normal Modes from Identified Complex Modes

A technique is presented to compute a set of normal modes from a set of measured (damped) complex modes. The number of elements in the modal vectors, which is equal to the number of measurements, can be larger than the number of modes under consideration. It is also shown in this paper that the practice of normal mode approximation to complex modes can lead to considerably large errors when the modes are too complex. A numerical example and a simulated experiment are presented to illustrate the concepts discussed and to support the theory presented.

Ibrahim, S. R.↗
NASA NTRS1985

Dynamic Modeling of Structures from Measured Complex Modes

A technique is presented to use a set of identified complex modes together with an analytical mathematical model of a structure under test to compute improved mass, stiffness and damping matrices. A set of identified normal modes, computed from the measured complex modes, is used in the mass orthogonality equation to compute an improved mass matrix. This eliminates possible errors that may result from using approximated complex modes as normal modes. The improved mass matrix, the measured complex modes and the higher analytical modes are then used to compute the improved stiffness and damping matrices. The number of degrees-of-freedom of the improved model is limited to equal the number of elements in the measured modal vectors. A simulated experiment shows considerable improvements, in the system's analytical dynamic model, over the frequency range of the given measured modal information.

Ibrahim, S. R.↗
NASA NTRS1983

Time-Domain Modal Vibration Identification

Ibrahim Time-Domain modal vibration identification program (ITD) uses multiple free-decay responses of test structure directly in time domain to identify modal parameters of structure: natural frequencies, damping factors and damped mode shapes. ITD written in FORTRAN.

Ibrahim, S. R.↗
NASA NTRS1982

Determination of normal modes from measured complex modes

A technique is presented for computing a set of normal modes from a set of measured complex modes. The number of elements in the modal vectors, which is equal to the number of measurements, can be larger than the number of modes under consideration. It is also shown that the practice of normal mode approximation to complex modes can lead to very large errors when the modes are too complex. A numerical example and a simulated experiment illustrate the concepts discussed and support the theory presented.

Ibrahim, S. R.↗
NASA NTRS1981

Large modal survey testing using the Ibrahim time domain /ITD/ identification technique

The ability of the ITD identification algorithm in identifying a complete set of structural modal parameters using a large number of free-response time histories simultaneously in one analysis, assuming a math model with a high number of degrees-of-freedom, has been studied. Identification results using simulated free responses of a uniform rectangular plate, with 225 measurement stations, and experimental responses from a ground vibration test of the Long Duration Exposure Facility (LDEF) Space Shuttle payload, with 142 measurement stations, are presented. As many as 300 degrees-of-freedom were allowed in analyzing these data. In general, the use of a significantly oversized math model in the identification process was found to maintain or increase identification accuracy and to identify modes of low response level that are not identified with smaller math model sizes. The concept of a Mode Shape Correlation Constant is introduced for use when more than one identification analysis of the same structure are conducted. This constant quantifies the degree of correlation between any two sets of complex mode shapes identified using different excitation conditions, different user-selectable algorithm constants, or overlapping sets of measurements.

Ibrahim, S. R.↗
NASA NTRS1978

Comparison of modal test methods on the Voyager payload

A comparison of the performance of modern modal data analysis methods on test data from the Voyager Jupiter/Saturn payload is presented. Four different test/data-analysis combinations are compared - multiple-point sine excitation tests, single-point random-excitation tests using two different techniques of manipulating Fourier transform data, and a time-domain method for analyzing random data. Results indicate that all four methods can give comparable results. Of the four, the time-domain approach detects more modes in the test data and, at the same time, shows the greatest promise for reducing the time and cost of modal testing.

Hanks, B. R.↗
NASA NTRS1978

Modal confidence factor in vibration testing

The modal confidence factor (MCF) is a number calculated for every identified mode for a structure under test. The MCF varies from 0.00 for a distorted nonlinear, or noise mode to 100.0 for a pure structural mode. The theory of the MCF is based on the correlation that exists between the modal deflection at a certain station and the modal deflection at the same station delayed in time. The theory and application of the MCF are illustrated by two experiments. The first experiment deals with simulated responses from a two-degree-of-freedom system with 20%, 40%, and 100% noise added. The second experiment was run on a generalized payload model. The free decay response from the payload model contained 22% noise.

Ibrahim, S. R.↗
NASA NTRS1978

Modal confidence factor in vibration testing

The theory and applications of a time domain modal test technique are presented. The method uses free decay of random responses from a structure under test to identify its modal characteristics namely, natural frequencies, damping factors, and mode shapes. The method can identify multimodal (highly coupled) systems and modes that have very small contribution in the responses. A method is presented to decrease the effects of high levels of noise in the data and thus improve the accuracy of identified parameters. This is accomplished using an oversized mathematical model. The concept of modal confidence factor (MCF) is developed. The MCF is a number calculated for every identified mode for a structure under test. The MCF varies from 0.000 for a distorted, nonlinear, or noise mode to 100.0 for a pure structural mode. The theory of the MCF is based on the correlation that exits between the modal deflection at a certain station and the modal deflection at the same station delayed in time. The theory and application of the MCF is illustrated by two experiments. The first experiment deals with simulated responses from a two degree of freedom system with 20 percent, 40 percent, and 100 percent noise added. The second experiment was run on a generalized payload model. The free decay response from the payload model contained about 22 percent noise.

Ibrahim, S. R.↗
NASA NTRS1977

The use of random decrement technique for identification of structural modes of vibration

An algorithm is developed to obtain the free responses of a structure from its random responses due to some unknown or known random input or inputs, using the random-decrement technique without changing time correlation between signals. The algorithm is tested using random responses from a 'generalized payload' model and from the 'Space Shuttle' model. The resulting free responses are then used to identify the modal characteristics of the two systems.

Ibrahim, S. R.↗