Engineering Papers⌕ Search

Engineering topics

Hyer, M. W.

Publications and source records attributed to Hyer, M. W..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Bending response of thin-walled laminated composite cylinders

Closed-form linear response solutions are presented for the bending response of thin-walled laminated composite cylinders. Displacements and intralaminar stresses are computed using the Donnell theory, and interlaminar stresses are computed using 3D equilibrium equations of elasticity. Laminates with stacking sequencies and an aluminum cylinder are used to illustrate the displacement response, intralaminar, and interlaminar stresses for two length-to-radius ratios of 1 and 5. Data obtained indicate that if only fiber breakage causes ultimate failure, material failure will occur on the compression side of the cylinders, at the ends, due to fiber compression. The interlaminar normal stress is an order of magnitude smaller than the interlaminar shear stresses and it is not likely to initiate failure.

Fuchs, H. P.↗
NASA NTRS1991

Thermal buckling and postbuckling of symmetrically laminated composite plates

The thermal buckling and postbuckling response of symmetrically laminated composite plates are discussed. Using variational methods in conjunction with a Rayleigh-Ritz formulation, thermal buckling and postbuckling are investigated for two laminates, a (+/- 45/0/90) and a (+/- 45/02), under two different simple support conditions, fixed and sliding. These laminates are subjected to the condition of a uniform temperature change. The effects of the principal material axis not being aligned with the edges of the plate, referred to here as material axis skewing, are also investigated. Although differences between buckling temperatures for the two support conditions were small, support conditions can have a large influence on thermal postbuckling response. In general, plates with fixed simple supports deflect more than plates with sliding simple supports. In addition, support conditions can influence modal interaction. Skewing of the material axis decreases the buckling temperatures of both laminates and, like fixed support conditions, causes increased postbuckling deflections. Skewing also influences modal interaction.

Meyers, C. A.↗
NASA NTRS1991

A study of the response of nonlinear springs

The various phases to developing a methodology for studying the response of a spring-reinforced arch subjected to a point load are discussed. The arch is simply supported at its ends with both the spring and the point load assumed to be at midspan. The spring is present to off-set the typical snap through behavior normally associated with arches, and to provide a structure that responds with constant resistance over a finite displacement. The various phases discussed consist of the following: (1) development of the closed-form solution for the shallow arch case; (2) development of a finite difference analysis to study (shallow) arches; and (3) development of a finite element analysis for studying more general shallow and nonshallow arches. The two numerical analyses rely on a continuation scheme to move the solution past limit points, and to move onto bifurcated paths, both characteristics being common to the arch problem. An eigenvalue method is used for a continuation scheme. The finite difference analysis is based on a mixed formulation (force and displacement variables) of the governing equations. The governing equations for the mixed formulation are in first order form, making the finite difference implementation convenient. However, the mixed formulation is not well-suited for the eigenvalue continuation scheme. This provided the motivation for the displacement based finite element analysis. Both the finite difference and the finite element analyses are compared with the closed form shallow arch solution. Agreement is excellent, except for the potential problems with the finite difference analysis and the continuation scheme. Agreement between the finite element analysis and another investigator's numerical analysis for deep arches is also good.

Hyer, M. W.↗
NASA NTRS1991

The use of curvilinear fiber format to improve buckling resistance of composite plates with central circular holes

The gains in buckling performance are explored that can be achieved by deviating from the conventional straightline fiber format and considering the situation whereby the fiber orientation in a layer, or a group of layers, can vary from point to point. The particular situation studied is a simply supported square plate with a centrally located hole loaded in compression. By using both a sensitivity analysis and a gradient-search technique, fiber orientation in a number of regions of the plate are selected so as to increase the buckling load relative to baseline straightline designs. The sensitivity analysis is used to determine which regions of the plate have the most influence on buckling load, and the gradient search is used to find the design that is believed to represent the absolute maximum buckling load for the conditions prescribed. Convergence studies and sensitivity of the final design are discussed. By examining the stress resultant contours, it is shown how the curvilinear fibers move the load away from the unsupported hole region of the plate to the supported edges, thus increasing the buckling capacity. The tensile capacity of the improved buckling design is investigated, and it is shown that both tensile capacity and buckling capacity can be improved with the curvilinear fiber concept.

Hyer, M. W.↗
NASA NTRS1991

Thermal buckling of symmetrically laminated composite plates

This paper discusses an investigation into the thermal buckling of symmetrically laminated composite plates. In this study thermal buckling is investigated for laminates under two different simple support conditions, fixed and sliding. These laminates are subjected to the conditions of a uniform temperature change, and a temperature change varying linearly along the length of the plate. The effects of the principal material axes not being aligned with the edges of the plate are also investigated. The buckling response is studied using variational methods, specifically the Trefftz criterion. A Rayleigh-Ritz formulation is used to obtain numerical results from the formulations for the prebuckling response and the buckling response.

Meyers, C. A.↗
NASA NTRS1990

The use of curvilinear fiber format to improve buckling resistance of plates with central circular holes

The potential gain in buckling resistance is explored by using the curvilinear format with a plate containing a centrally located circular hole and subjected to a uniaxial compressive load. The buckling loads for a uniform stress loading and simple support boundary conditions were examined. The method of analysis is outlined for the buckling improvement study. Several designs that represent an improvement over a baseline quasi-isotropic design (a design that is quite good for buckling resistance) are discussed. The tensile load of these designs is examined. A recommended design is presented that not only shows an improved buckling capacity, but also shows improved tensile performance. Follow-on activities are also discussed.

Lee, H. H.↗
NASA NTRS1990

Innovative design of composite structures: Axisymmetric deformations of unsymmetrically laminated cylinders loaded in axial compression

The study focuses on the axisymmetric deformation response of unsymmetrically laminate cylinders loaded in axial compression by known loads. A geometrically nonlinear analysis is used. Though buckling is not studied, the deformations can be considered to be the prebuckling response. Attention is directed at three 16 layer laminates: a (90 sub 8/0 sub 8) sub T; a (0 sub 8/90 sub 8) sub T and a (0/90) sub 4s. The symmetric laminate is used as a basis for comparison, while the two unsymmetric laminates were chosen because they have equal but opposite bending-stretching effects. Particular attention is given to the influence of the thermally-induced preloading deformations that accompany the cool-down of any unsymmetric laminate from the consolidation temperature. Simple support and clamped boundary conditions are considered. It is concluded that: (1) The radial deformations of an unsymmetric laminate are significantly larger than the radial deformations of a symmetric laminate, although for both symmetric and unsymmetric laminates the large deformations are confined to a boundary layer near the ends of the cylinder; (2) For this nonlinear problem the length of the boundary layer is a function of the applied load; (3) The sign of the radial deformations near the supported end of the cylinder depends strongly on the sense (sign) of the laminate asymmetry; (4) For unsymmetric laminates, ignoring the thermally-induced preloading deformations that accompany cool-down results in load-induced deformations that are under predicted; and (5) The support conditions strongly influence the response but the influence of the sense of asymmetry and the influence of the thermally-induced preloading deformations are independent of the support conditions.

Hyer, M. W.↗
NASA NTRS1990

Innovative design of composite structures: The use of curvilinear fiber format in structural design of composites

The influence is investigated of a curvilinear fiber format on load carrying capacity of a layered fiber reinforced plate with a centrally located hole. A curvilinear fiber format is descriptive of layers in a laminate having fibers which are aligned with the principal stress directions in those layers. Laminates of five curvilinear fiber format designs and four straightline fiber format designs are considered. A quasi-isotropic laminate having a straightline fiber format is used to define a baseline design for comparison with the other laminate designs. Four different plate geometries are considered and differentiated by two values of hole diameter/plate width equal to 1/6 and 1/3, and two values of plate length/plate width equal to 2 and 1. With the plates under uniaxial tensile loading on two opposing edges, alignment of fibers in the curvilinear layers with the principal stress directions is determined analytically by an iteration procedure. In-plane tensile load capacity is computed for all of the laminate designs using a finite element analysis method. A maximum strain failure criterion and the Tsai-Wu failure criterion are applied to determine failure loads and failure modes. Resistance to buckling of the laminate designs to uniaxial compressive loading is analyzed using the commercial code Engineering Analysis Language. Results indicate that the curvilinear fiber format laminates have higher in-plane tensile load capacity and comparable buckling resistance relative to the straightline fiber format laminates.

Charette, R. F.↗
NASA NTRS1990

Innovative design of composite structures: The use of curvilinear fiber format to improve buckling resistance of composite plates with central circular holes

The gains in buckling performance are explored that can be achieved by deviating from the conventional straightline fiber format and considering the situation whereby the fiber orientation in a layer, or a group of layers, can vary from point to point. The particular situation studied is a simply supported square plate with a centrally located hole loaded in compression. By using both a sensitivity analysis and a gradient-search technique, fiber orientation in a number of regions of the plate are selected so as to increase the buckling load relative to baseline straightline designs. The sensitivity analysis is used to determine which regions of the plate have the most influence on buckling load, and the gradient search is used to find the design that is believed to represent the absolute maximum buckling load for the conditions prescribed. Convergence studies and sensitivity of the final design are discussed. By examining the stress resultant contours, it is shown how the curvilinear fibers move the load away from the unsupported hole region of the plate to the supported edges, thus increasing the buckling capacity. The tensile capacity of the improved buckling design is investigated, and it is shown that both tensile capacity and buckling capacity can be improved with the curvilinear fiber concept.

Hyer, M. W.↗
NASA NTRS1990

Innovative design of composite structures: The use of curvilinear fiber format in composite structure design

The gains in structural efficiency are investigated that can be achieved by aligning the fibers in some or all of the layers in a laminate with the principal stress directions in those layers. The name curvilinear fiber format is given to this idea. The problem studied is a plate with a central circular hole subjected to a uniaxial tensile load. An iteration scheme is used to find the fiber directions at each point in the laminate. Two failure criteria are used to evaluate the tensile load capacity of the plates with a curvilinear format, and for comparison, counterpart plates with a conventional straightline fiber format. The curvilinear designs for improved tensile capacity are then checked for buckling resistance. It is concluded that gains in efficiency can be realized with the curvilinear format.

Hyer, M. W.↗
NASA NTRS1990

The development of an alternative thermoplastic powder prepregging technique

Discussed is a novel powder prepregging technique that is based on the deposition of the powder onto fibers that have been moistened using an ultrasonic humidifier. The moisture acts as an initial binding agent for the powder until the powder can be melted onto the fiber in a subsequent heating step. LaRC-TPI powder, produced by Mitsui Toastsu, and Hercules AS-4 fiber served as the process development material system. The influence of powder particle size on this process, and the quality of the resulting composite are discussed.

Ogden, A. L.↗
NASA NTRS1990

Thermal buckling and post-buckling of symmetric composite plates

The thermally induced buckling and postbuckling behavior of square and rectangular simply supported composite plates is examined using the Rayleigh-Ritz method in conjunction with the second variations of the total potential energy. Spatially uniform and nonuniform temperatures and laminates with material axes that are not aligned with the plate edges (skewed material axes) are considered. Results of the analysis are presented in graphic form.

Meyers, C. A.↗
NASA NTRS1989

The structural response of unsymmetrically laminated composite cylinders

The responses of an unsymmetrically laminated fiber-reinforced composite cylinder to an axial compressive load, a torsional load, and the temperature change associated with cooling from the processing temperature to the service temperature are investigated. These problems are considered axisymmetric and the response is studied in the context of linear elastic material behavior and geometrically linear kinematics. Four different laminates are studied: a general unsymmetric laminate; two unsymmetric but more conventional laminates; and a conventional quasi-isotropic symmetric laminate. The responses based on closed-form solutions for different boundary conditions are computed and studied in detail. Particular emphasis is directed at understanding the influence of elastic couplings in the laminates. The influence of coupling decreased from a large effect in the general unsymmetric laminate, to practically no effect in the quasi-isotropic laminate. For example, the torsional loading of the general unsymmetric laminate resulted in a radial displacement. The temperature change also caused a significant radial displacement to occur near the ends of the cylinder. On the other hand, the more conventional unsymmetric laminate and the quasi-isotropic cylinder did not deform radially when subjected to a torsional load. From the results obtained, it is clear the degree of elastic coupling can be controlled and indeed designed into a cylinder, the degree and character of the coupling being dictated by the application.

Butler, T. A.↗
NASA NTRS1989

Thermally-induced stresses in graphite-epoxy tubes coated with aluminum foil

Thermally-induced stresses in the foil, adhesive, and graphite-epoxy layers of composite tubes with aluminum foil bonded to the inner and outer surface are computed. The thermal effects are due to a temperature decrease from the processing temperature of the material to a temperature felt to represent the space environment, the intended operating environment of the tubes. Tubes fabricated from T300/934 and P75s/934 material systems are considered. The results indicate that the presence of the foil and adhesive have no detrimental effect on the stresses in the tube.

Knott, Tamara W.↗
NASA NTRS1989

The use of curvilinear fiber format in composite structure design

This paper investigates the gains in structural efficiency that can be achieved by aligning the fibers in some or all of the layers in a laminate with the principal stress directions in those layers. The name curvilinear fiber format is given to this idea. The problem studied is a plate with a central circular hole subjected to a uniaxial tensile load. An iteration scheme is used to find the fiber directions at each point in the laminate. Two failure criteria are used to evaluate the tensile load capacity of the plates with a curvilinear format, and for comparison, counterpart plates with a conventional straightline fiber format. The curvilinear designs for improved tensile capacity are then checked for buckling resistance. It is concluded that gains in efficiency can be realized with the curvilinear format.

Hyer, M. W.↗
NASA NTRS1989

Mechanics of unsymmetric laminates

Theoretical models describing the mechanical behavior of fiber-reinforced composite laminates are developed analytically and demonstrated. The curing of composite structures and the out-of-plane shapes of unsymmetric laminates are discussed and illustrated with photographs; the derivation of the governing equations is outlined; numerical results for typical laminates are presented in graphs; and particular attention is given to stability considerations and the effects of material properties, laminate thickness, aspect ratio, and stacking sequence.

Hyer, M. W.↗