Engineering topics
Publications and source records attributed to Hunter, Gary.
Missions to the surface of Venus have had limitedlife due to the extreme environmental conditions. Theshort life has limited the science that is achievable,and there are gaps in some science, such asseismology, which is enabled by long life. This worksummarizes technical advances that are preparing usfor long-duration (weeks to months) Venus surfacemissions.
LEAVES (Lofted Environmental Atmospheric Venus Sensors) is a design exercise with the goal of dramatically decreasing the cost of obtaining prioritized chemical and physical data in planetary atmospheres. Through the application of a swarm approach this concept parallelizes atmospheric exploration, with geographic coverage far exceeding what is possible with conventional monolithic platforms or sondes. Each unit in the swarm is exceptionally compact, with a powered payload mass of only a few tens of grams and a high-drag, semi-rigid structure that acts to slow each probe as it descends through the atmosphere. This structural design can collapse into a planar form to allow for efficient stowage prior to arrival at the target body. With a total per-unit mass of only 120 g, a fleet of 100 (or more) units can be very reasonably accommodated on a carrier spacecraft.Science operations, which begin when the LEAVES probes reach an altitude of 100 km, are targeted for the cloud-bearing region of Venus' atmosphere. During the roughly 9 hour, terminal velocity descent through the atmosphere, LEAVES collects data of the state and composition of the atmosphere in parallel across multiple units. These data would represent an unprecedented constraint on the distribution and concentration of targeted chemical species, and the detection of local and regional variations in both chemistry and physical properties.A novel and compelling result of this exercise was that the same optimization that produced a structure with an exceptionally low areal mass density (0.126 kg/m2) also resulted in a probe that can be deployed directly from an aerobraking orbit (~140 km at 5 km/s) without the need for aeroshell protection. This translates to a tremendous mass savings and gives LEAVES the flexibility to be carried as a secondary payload aboard either a descending surface probe or an orbital radar mapper. Because such missions are under active development or have already been proposed (but not flown), we infer that LEAVES is well positioned as a technology
Many crucial geophysical and atmospheric science investigations at Venus require operations on the surface for an entire solar day. Until recently this was not achievable, but new developments in high temperature electronics have now made months long operations on the Venus surface possible even with smallsat class missions. Here we describe a study of a long-lived Venus lander called SAEVe, for Seismic and Atmospheric Exploration of Venus: this was one of the concepts selected in 2017 under NASA's Planetary Science Deep Space SmallSat Studies (PSDS3) call.
NASA's science mission directorate has put increasing emphasis on innovative, smaller, and lower cost missions to achieve their science objectives. One example of this was the recent call by the Planetary Science Division for cube and small satellite concepts expected to cost $100M or less, not including launch and weighing less than 180kg. Over 100 proposals were submitted suggesting that indeed this is a size of mission worthy of being considered in future planning. Nineteen missions were selected for study, one being a long-lived Venus mission called SAEVe, for Seismic and Atmospheric Exploration of Venus. The science objectives and relevance of SAEVe include: Is Venus seismically active? What can we learn about its crust (thickness and composition) and its interior (lithosphere, mantle, and core)? What can be learned about its evolutionary history or about the planet / atmosphere interactions? SAEVe begins to address these science questions with simple, but capable, instrumented probes that can survive on the surface of Venus and take temporal measurements over months something never attempted before. The data returned will further our understanding of the solar system and Earth, and aid in meeting the NASA Science Plan goal to ascertain the content, origin, and evolution of the solar system and the chemical and physical processes in our solar system. SAEVe is delivered to Venus as a ride-along on another mission to Venus. Its two small probes are placed into the Venus atmosphere via a single Stardust-like entry capsule, are ejected at different times, free fall, and decelerate in the thickening atmosphere to touchdown under 8 m/s2 or less. The probes will begin taking measurements and transmitting important parameters at or near the surface and will focus on measurements like seismic activity, heat flux, wind speed and direction, basic chemical abundances, temperature, and pressure. At preset intervals, the probes acquire the science measurements and beam the data to the orbiting host spacecraft. SAEVe will serve as a highly capable precursor and pave the way for larger and more complex lander missions to explore Venus.
This presentation provides an update on development of the Long-Lived In-situ Solar System Explorer (LLISSE). LLISSE is a small probe being developed to provide long-term measurements of simple but important scientific parameters from the surface of Venus. High level summary of recent activities and progress is provided. LLISSE is a small and completely independent probe for Venus surface applications
This presentation and poster provide a brief overview on the Long-Lived In-situ Solar System Explorer (LLISSE). This is a small probe being developed to provide long-term measurements of simple but important scientific parameters from the surface of Venus. This is a revolutionary concept to Venus exploration and promises to change our paradigm of exploring this unique and challenging environment.
NASA Centers continue to collaborate to characterize the chemical species and smoke particles generated by the combustion of current space-rated non-metallic materials including fluoropolymers. This paper describes the results of tests conducted February through September 2012 to identify optimal chemical markers both for augmenting particle-based fire detection methods and for monitoring the post-fire cleanup phase in human spacecraft. These studies follow up on testing conducted in August 2010 and reported at ICES 2011. The tests were conducted at the NASA White Sands Test Facility in a custom glove box designed for burning fractional gram quantities of materials under varying heating profiles. The 623 L chamber was heavily instrumented to quantify organics (gas chromatography/mass spectrometry), inorganics by water extraction followed by ion chromatography, and select species by various individual commercially-available sensors. Evaluating new technologies for measuring carbon monoxide, hydrogen cyanide, hydrogen fluoride, hydrogen chloride and other species of interest was a key objective of the test. Some of these sensors were located inside the glovebox near the fire source to avoid losses through the sampling lines; the rest were located just outside the glovebox. Instruments for smoke particle characterization included a Tapered Element Oscillating Microbalance Personal Dust Monitor (TEOM PDM) and a TSI Dust Trak DRX to measure particle mass concentration, a TSI PTrak for number concentration and a thermal precipitator for collection of particles for microscopic analysis. Materials studied included Nomex®, M22759 wire insulation, granulated circuit board, polyvinyl chloride (PVC), Polytetrafluoroethylene (PTFE), Kapton®, and mixtures of PTFE and Kapton®. Furnace temperatures ranged from 340o to 640o C, focusing on the smoldering regime. Of particular interest in these tests was confirming burn repeatability and production of acid gases with different fuel mixture compositions, as well as the dependence of aerosol concentrations on temperature.
NASA Centers continue to collaborate to characterize the chemical species and smoke particles generated by the combustion of current space-rated non-metallic materials including fluoropolymers. This paper describes the results of tests conducted February through September 2012 to identify optimal chemical markers both for augmenting particle-based fire detection methods and for monitoring the post-fire cleanup phase in human spacecraft. These studies follow up on testing conducted in August 2010 and reported at ICES 2011. The tests were conducted at the NASA White Sands Test Facility in a custom glove box designed for burning fractional gram quantities of materials under varying heating profiles. The 623 L chamber was heavily instrumented to quantify organics (gas chromatography/mass spectrometry), inorganics by water extraction followed by ion chromatography, and select species by various individual commercially-available sensors. Evaluating new technologies for measuring carbon monoxide, hydrogen cyanide, hydrogen fluoride, hydrogen chloride and other species of interest was a key objective of the test. Some of these sensors were located inside the glovebox near the fire source to avoid losses through the sampling lines; the rest were located just outside the glovebox. Instruments for smoke particle characterization included a Tapered Element Oscillating Microbalance Personal Dust Monitor (TEOM PDM) and a TSI Dust Trak DRX to measure particle mass concentration, a TSI PTrak for number concentration and a thermal precipitator for collection of particles for microscopic analysis. Materials studied included Nomex(R), M22759 wire insulation, granulated circuit board, polyvinyl chloride (PVC), Polytetrafluoroethylene (PTFE), Kapton(R), and mixtures of PTFE and Kapton(R). Furnace temperatures ranged from 340 to 640 C, focusing on the smoldering regime. Of particular interest in these tests was confirming burn repeatability and production of acid gases with different fuel mixture compositions, as well as the dependence of aerosol concentrations on temperature.
The aerospace industry requires development of a range of chemical-sensor technologies for applications including emissions monitoring as well as fuel-leak and fire detection. Improvements in sensing technology are necessary to increase safety, reduce emissions, and increase performance. The overall aim is to develop intelligent-vehicle systems that can autonomously monitor their state and respond to environmental changes. A range of chemical sensors is under development to meet these needs, based in part on microfabrication technology which produces sensors of minimal size, weight, and power consumption. We have fabricated a range of sensor platforms, integrated them with hardware to form complete sensor systems, and demonstrated their applicability.
No abstract available
The objective of this research is to use a combination of carbon nanotubes and silicon-based microfabrication and micromachining processes to produce unique micro-sized chemical and gaseous sensors. Polished quartz substrate is used. Interdigitated structure is used for the sensing elements. Metallic catalysts for the growth of the carbon nanotube include copper, iron, nickel, and cobalt. Various thicknesses of the metallic catalysts are used in this study varying between 5 to 20 microns. Depositing of the metallic catalyst is accomplished using an ion-beam sputtering thin film technique and a shadow mask. Single wall carbon nanotubes are successfully formed over the metallic catalyst layer. Preliminary measurements of the carbon nanotubes show this nanotube contained film over the sensing elements which had a resistance value of 400 ohms at room temperature. This is a more conductive film comparing to metal oxide films, such as SnO2 or ZnO, that are now widely used in gaseous sensor research. Evaluation of the carbon nanotube film for potential gaseous sensing will be carried out.
The goals of the project described in this viewgraph presentation are the following: (1) Increase safety by understanding operating conditions and component capabilities; and (2) Reduce development and operating costs by reducing testing and design cycle times and reducing engine weight and increasing component life. The objectives are to determine cooling system effectiveness and structural loads.