Engineering Papers⌕ Search

Engineering topics

Hunt, J. L.

Publications and source records attributed to Hunt, J. L..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Aerodynamic heat transfer to a hypersonic research aircraft model /X-24C/ at Mach 6

The paper reports on results of heat-transfer tests conducted on a 1/29-scale model of the X-24C-12I hypersonic research aircraft configuration in a Mach 6 tunnel at a Reynolds number of thirteen million using the phase-change heat transfer technique. Sequences of phase-change heat transfer pattern photographs are presented showing windward side and leeward side heating processes. Theoretical predictions of dimensionless heat transfer coefficients along a data line on lower fuselage and on fuselage side bracket the experimental values. A turbulent heating theory gives good agreement with data when shifted to a new virtual origin.

Lawing, P. L.↗
NASA NTRS1975

Normal- and oblique-shock flow parameters in equilibrium air including attached-shock solutions for surfaces at angles of attack, sweep, and dihedral

Normal- and oblique-shock flow parameters for air in thermochemical equilibrium are tabulated as a function of shock angle for altitudes ranging from 15.24 km to 91.44 km in increments of 7.62 km at selected hypersonic speeds. Post-shock parameters tabulated include flow-deflection angle, velocity, Mach number, compressibility factor, isentropic exponent, viscosity, Reynolds number, entropy difference, and static pressure, temperature, density, and enthalpy ratios across the shock. A procedure is presented for obtaining oblique-shock flow properties in equilibrium air on surfaces at various angles of attack, sweep, and dihedral by use of the two-dimensional tabulations. Plots of the flow parameters against flow-deflection angle are presented at altitudes of 30.48, 60.96, and 91.44 km for various stream velocities.

Hunt, J. L.↗
NASA NTRS1974

Use of hexafluoroethane to simulate the inviscid real-gas effects on blunt entry vehicles

Results are presented of an experimental and theoretical investigation of the use of equilibrium hexafluoroethane C2F6 as an undissociated test gas in a wind tunnel to simulate the inviscid aerodynamic characteristics of blunt bodies in high-speed flight where dissociation occurs. The results indicate that the use of C2F6 as a test gas in wind tunnels is a practical and relatively simple and inexpensive method of obtaining test conditions with large normal-shock density ratios. Equations for the thermodynamic and transport properties of C2F6 are also included.

Hunt, J. L.↗
NASA NTRS1974

Simulation of real-gas effects for Mars entry

The changes in aerodynamic characteristics due to real-gas effects associated with high speed flight (characterized by large shock density ratios) are primarily the result of changes in surface pressures acting on the forebody. The surface pressures are affected by a change in shock density ratio (real-gas effects) in two ways. First, the level of pressure at the stagnation point relative to freestream dynamic pressure is changed, and second, the distribution of surface pressure relative to stagnation-point pressure is changed. The density-ratio effect on the stagnation point pressure level can be estimated by considering the flow of a perfect gas about a blunt body.

Hunt, J. L.↗
NASA NTRS1973

Measured pressure distributions of large-angle cones in hypersonic flows of tetrafluoromethane, air, and helium

An experimental study of surface pressure distributions on a family of blunt and sharp large angle cones was made in hypersonic flows of helium, air, and tetrafluoromethane. The effective isentropic exponents of these flows were 1.67, 1.40, and 1.12. Thus, the effect of large shock density ratios such as might be encountered during planetary entry because of real-gas effects could be studied by comparing results in tetrafluoromethane with those in air and helium. It was found that shock density ratio had a large effect on both shock shape and pressure distribution. The differences in pressure distribution indicate that for atmospheric flight at high speed where real-gas effects produce large shock density ratios, large-angle cone vehicles can be expected to experience different trim angles of attack, drag coefficient, and lift-drag ratios than those for ground tests in air wind tunnels.

Jones, R. A.↗
NASA NTRS1973

Thermodynamic and transport properties of gaseous tetrafluoromethane in chemical equilibrium

Equations and in computer code are presented for the thermodynamic and transport properties of gaseous, undissociated tetrafluoromethane (CF4) in chemical equilibrium. The computer code calculates the thermodynamic and transport properties of CF4 when given any two of five thermodynamic variables (entropy, temperature, volume, pressure, and enthalpy). Equilibrium thermodynamic and transport property data are tabulated and pressure-enthalpy diagrams are presented.

Hunt, J. L.↗
NASA NTRS1973

Application of phase-change technique to thin sections with heating on both surfaces

A numerical digital computer program was developed to calculate the heat-transfer coefficients for both sides of a one-dimensional finite slab subject to the boundary conditions ascribed to the phase-change coating heat-transfer technique. In a typical tunnel test situation where a thin wing was exposed to heating on both sides, the data reduction procedures for a semi-infinite slab gave heat-transfer coefficients as much as 375 percent too high on the side with the lowest heating. The results from the one-dimensional finite-slab procedure are presented in the form of correction factors to the solution for a semi-infinite slab in terms of parameters normally used with the phase-change heat-transfer technique. These correlations are not restricted to slab thickness or thermophysical properties and are easily used to obtain accurate data on thin model sections.

Hunt, J. L.↗
NASA NTRS1973

Heating and flow-field studies on a straight-wing hypersonic reentry vehicle at angles of attack from 20 to 80 deg with simulation of real-gas trends

Data are presented from a series of phase-change heat transfer and flow visualization tests at Mach 7.4, 8, and 10.3 in air, Mach 19.5 in nitrogen, Mach 20.3 in helium, and Mach 6 in tetrafluoromethane (CF4) on the windward surface of a straight wing hypersonic reentry configuration for angles of attack from 20 deg to 80 deg. The results indicate that: (1) for hypersonic stream Mach numbers, the flow field over the straight-wing configuration is essentially independent of Mach number, (2) transition Reynolds number decreases with increasing angle of attack, (3) at some critical angle of attack, the wing-shock standoff distance is greatly increased and the stagnation line moves downstream from the wing leading edge, (4) value of the critical angle of attack is very sensitive to the flow shock density ratio or effective gamma, and (5) at angles of attack above the critical value for all gases, the nondimensional level of heat transfer to the wing is higher for the higher shock density ratio flows.

Hunt, J. L.↗
NASA NTRS1972

Photographing flow fields and heat-transfer patterns in color simultaneously.

A color-schlieren technique is described that combines the flow-field shock shapes and the phase-change coating to give a very descriptive account of aerodynamic heating. This technique employs, in addition to the conventional schlieren system, a temperature-sensitive material as a thin surface coating that undergoes a visible phase change from opaque solid to clear liquid at a known temperature. The resulting pictures can lead to a better understanding of shock/boundary layer interactions, as shown with the aid of a specific example.

Creel, T. R., Jr.↗
NASA NTRS1972

Heat transfer to four fineness-ratio-1.6 hexagonal prisms with various corner radii at Mach 6

An investigation was conducted in the Langley 20-inch Mach 6 tunnel to define the aerodynamic heat transfer to the radioisotope fuel cask (heat source) of the SNAP-19/Pioneer power system. The shape of the SNAP-19/Pioneer heat source is that of a hexagonal prism with flat ends; the fineness ratio, based on maximum (edge to edge) diameter, is 1.61. Phase-change-paint heat-transfer data and schlieren photographs were obtained on four possible 1/2-scale entry configurations of the SNAP-19/Pioneer heat source. Tests were conducted over a wide range of attitudes and at nominal Reynolds numbers, based on the length of the unablated configuration, of 33,000; 84,000; and 2,200,000.

Hunt, J. L.↗
NASA NTRS1971

Thin wing corrections for phase-change heat-transfer data.

Since no methods are available for determining the magnitude of the errors incurred when the semiinfinite slab assumption is violated, a computer program was developed to calculate the heat-transfer coefficients to both sides of a finite, one-dimensional slab subject to the boundary conditions ascribed to the phase-change coating technique. The results have been correlated in the form of correction factors to the semiinfinite slab solutions in terms of parameters normally used with the technique.

Hunt, J. L.↗