Engineering Papers⌕ Search

Engineering topics

Humrickhouse, Paul W

Publications and source records attributed to Humrickhouse, Paul W.

System Modeling of the HTTR and Economic Dispatch Model of the Secondary System

High Temperature Gas-cooled Reactors (HTGRs) can be used for the generation of electricity and their process heat can be used to improve the efficiency of chemical processes such as hydrogen production. The JAEA-operated High-Temperature engineering Test Reactor (HTTR-GT/H2) is exploring using the reactor for electricity and hydrogen production. A RELAP5-3D model of the HTTR-GT/H2 secondary system has been developed using design information. The various components and heat exchangers in the secondary system were modeled and results were compared to the design conditions. The results for the sole-power generation mode were shown to fit the design conditions very well. The largest temperature difference was on the order of 7 K, and the largest pressure difference was on the order of 0.05 MPa. The results for the hydrogen cogeneration mode did not match the design conditions nearly as well. The largest temperature difference was about 39 K and the largest pressure difference was about 0.27 MPa at the compressor outlet. The larger differences for the hydrogen cogeneration mode are attributed to the various complex components and the flow being split in the secondary loop. A transient reduction in heat removal capability of the secondary system was investigated. Reactor temperatures are anticipated to rise as a result. The core reactivity response due to this increase in temperature is investigated and is expected to add negative reactivity to the reactor. An economic dispatch model was developed for a nuclear-driven iodine-sulfur cycle system to determine hydrogen sale prices that would make such a system profitable. The study focuses on the development of the economic model and the role that input data plays on final calculated values. It was found that the input electricity prices, whether using historical data or a host of synthetic time histories, produce significantly different breakeven hydrogen sale prices. As such, great care should be used in these economic dispatch analyses to select reasonable input assumptions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Tritium Transport Phenomena in Molten-Salt Reactors: Molten Salt Tritium Transport Experiment Design

Tritium is produced from neutron interactions with both lithium and beryllium. Large quantities of tritium are generated in Molten Salt Reactors (MSRs) which use LiF/BeF2 (FLiBe) as the fuel salt. Tritium is unique among the radionuclide hazards as it readily permeates through metal structural materials at high temperatures. All metal surfaces are potential release paths for tritium. For adequate safety analysis and eventual licensing of new reactors, predictive models for tritium transport and release from MSRs must be developed. These models must account for the multiple transport phenomena involved with tritium: fuel salt phase mass transport, dissociation/recombination reactions on metal surfaces, interstitial diffusion through the metal structure, and salt or gas phase mass transport in the downstream fluid. These models also must also be validated with representative experiments. Our previous report outlined tritium transport phenomena involved in MSRs, made suggestions on gaps in the transport dataset, and proposed an experimental test stand to test combined transport effects – tritium transport through pipe walls in a convective salt flow. In this report, we summarize an updated analysis framework for tritium transport in MSRs, report our results on hydrogen and deuterium permeation through Hastelloy N, and describe the final design of the Molten Salt Tritium Transport Experiment (MSTTE, pronounced “misty”). The MSRE provides the only wholistic experimental data set for tritium transport in MSRs and understanding the transport phenomena involved in the MSRE is crucial for future model development. One set of parameters in our analysis framework was unknown for the MSRE—surface reaction rates for tritium on Hastelloy N. This warranted our hydrogen and deuterium permeation campaign to assess the permeability, diffusivity, and solubility of hydrogen isotopes in clean Hastelloy N. Surface reaction rate constants were probed by low pressure measurements, however, no surface effects were observed in the limits of our permeation apparatus. Permeation experiments on oxidized Hastelloy N were not performed for this report but are planned in future work. The experimental test stand, MSTTE, measures combined transport properties of the salt-metal system. MSTTE is a forced convection FLiBe loop with custom designed test section to measure tritium transport through candidate structural materials. We use MSRE relevant dimensionless numbers to design and scale the test section. Hastelloy N is a candidate loop and test section material due to the relevance for the MSRE and related designs, however, other metals are being considered (e.g. 316H SS) which may better align with current vendor concepts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

ARPA-E Summit Presentation

Presentation for ARPA-E Energy Innovation Summit on May 24-27, 2021. Supporting ARPA-E GAMMOW project titled "Interfacial-Engineered Membranes for Efficient Tritium Extraction". Colorado School of Mines is lead and Idaho National Laboratory is a subcontract with CO-PI status.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tritium Transport Phenomena in Molten-Salt Reactors

In this work, we review phenomena relevant to tritium transport in molten-salt reactors, which produce tritium from lithium and beryllium salts at significantly higher levels than other reactor types. Modeling of such phenomena began following MSRE operations, and these early models attempted to predict measured tritium distributions in the MSRE, accounting for turbulent mass-transport processes (using established heat transfer correlations), permeation through a variety of metal structures such as heat exchanger tubes, and transport to and from bubbles introduced into the salt by gas sparging. The models reasonably reproduced the MSRE data, but did so best when the permeability of structures was reduced by about a factor of 1,000. This issue does not appear to have been conclusively resolved, and all of the more recent attempts to model tritium transport in molten salts appear to make use of the same methodology. MSRE remains, however, essentially our only source of integral tritium transport data relevant to MSRs. Here, we generalize the MSRE approach to permeation in order to include potential rate-limiting effects at interfaces, as well the effects of added hydrogen. Appropriately non-dimensionalized, this system of equations identifies two dimensionless numbers whose relative values clearly delineate the conditions under which mass transport, surface effects, permeation, and hydrogen swamping are expected to become rate-limiting. We also describe the preliminary conceptual design of a forced convection FLiBe loop, into which tritium would be introduced for the purpose of providing validation data for such a model. The primary purpose of this is to investigate the coupled transport phenomena described above and identify those that are rate-limiting in MSRs. Additional test section configurations are described that would address other transport phenomena relevant to MSRs, including bubbly flows and graphite interactions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

AGR-3/4 Modeling and Transport Parameters

Outline AGR-3/4 experiment and objectives Description of AGR-3/4 modeling approach and inputs Source term (release from particles) Temperature profiles Diffusion through concentric rings Adsorption across gaps between rings Simplified Source Model and updated model results Reconstruction of fission product distributions from gamma tomography data

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

MELCOR accident analysis for ARIES-ACT

We model a loss of flow accident (LOFA) in the ARIES-ACT1 tokamak design. ARIES-ACT1 features an advanced SiC blanket with LiPb as coolant and breeder, a helium cooled steel structural ring and tungsten divertors, a thin-walled, helium cooled vacuum vessel, and a room temperature water-cooled shield outside the vacuum vessel. The water heat transfer system is designed to remove heat by natural circulation during a LOFA. The MELCOR model uses time-dependent decay heats for each component determined by 1-D modeling. The MELCOR model shows that, despite periodic boiling of the water coolant, that structures are kept adequately cool by the passive safety system.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

HTGR Dust Safety Issues and Needs for Research and Development

This report presents a summary of high temperature gas-cooled reactor dust safety issues. It draws upon a literature review and the proceedings of the Very High Temperature Reactor Dust Assessment Meeting held in Rockville, MD in March 2011 to identify and prioritize the phenomena and issues that characterize the effect of carbonaceous dust on high temperature reactor safety. It reflects the work and input of approximately 40 participants from the U.S. Department of Energy and its National Labs, the U.S. Nuclear Regulatory Commission, industry, academia, and international nuclear research organizations on the topics of dust generation and characterization, transport, fission product interactions, and chemical reactions. The meeting was organized by the Idaho National Laboratory under the auspices of the Next Generation Nuclear Plant Project, with support from the U.S. Nuclear Regulatory Commission. Information gleaned from the report and related meetings will be used to enhance the fuel, graphite, and methods technical program plans that guide research and development under the Next Generation Nuclear Plant Project. Based on meeting discussions and presentations, major research and development needs include: generating adsorption isotherms for fission products that display an affinity for dust, investigating the formation and properties of carbonaceous crust on the inside of high temperature reactor coolant pipes, and confirming the predominant source of dust as abrasion between fuel spheres and the fuel handling system.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Comparison of Hyperelastic Models for Granular Materials

Three recently proposed hyperelastic models for granular materials are compared with experiment data. Though all three are formulated to give elastic moduli that are power law functions of the mean stress, they have rather different dependencies on individual stresses, and generally differ from well established experimental forms. Predicted static stress distributions are in qualitative agreement with experiments, but do not differ greatly from isotropic linear elasticity, and similarly fail to account for variability in experiment data that presumably occurs due to a preparation dependence of granular materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

HYPERELASTIC MODELS FOR GRANULAR MATERIALS

A continuum framework for modeling of dust mobilization and transport, and the behavior of granular systems in general, has been reviewed, developed and evaluated for reactor design applications. The large quantities of micron-sized particles expected in the international fusion reactor design, ITER, will accumulate into piles and layers on surfaces, which are large relative to the individual particle size; thus, particle-particle, rather than particle-surface, interactions will determine the behavior of the material in bulk, and a continuum approach is necessary and justified in treating the phenomena of interest; e.g., particle resuspension and transport. The various constitutive relations that characterize these solid particle interactions in dense granular flows have been discussed previously, but prior to mobilization their behavior is not even fluid. Even in the absence of adhesive forces between particles, dust or sand piles can exist in static equilibrium under gravity and other forces, e.g., fluid shear. Their behavior is understood to be elastic, though not linear. The recent “granular elasticity” theory proposes a non-linear elastic model based on “Hertz contacts” between particles; the theory identifies the Coulomb yield condition as a requirement for thermodynamic stability, and has successfully reproduced experimental results for stress distributions in sand piles. The granular elasticity theory is developed and implemented in a stand- alone model and then implemented as part of a finite element model, ABAQUS, to determine the stress distributions in dust piles subjected to shear by a fluid flow. We identify yield with the onset of mobilization, and establish, for a given dust pile and flow geometry, the threshold pressure (force) conditions on the surface due to flow required to initiate it. While the granular elasticity theory applies strictly to cohesionless granular materials, attractive forces are clearly important in the interaction of micron-sized particles; extension of the theory to account for these effects is also considered. A set of continuum models are proposed for use in the future dust transport modeling.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗