Engineering Papers⌕ Search

Engineering topics

Hughes, D. L.

Publications and source records attributed to Hughes, D. L..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Net thrust calculation sensitivity of an afterburning turbofan engine to variations in input parameters

The calculated value of net thrust of an aircraft powered by a General Electric F404-GE-400 afterburning turbofan engine was evaluated for its sensitivity to various input parameters. The effects of a 1.0-percent change in each input parameter on the calculated value of net thrust with two calculation methods are compared. This paper presents the results of these comparisons and also gives the estimated accuracy of the overall net thrust calculation as determined from the influence coefficients and estimated parameter measurement accuracies.

Hughes, D. L.↗
NASA NTRS1985

Effects of inlet distortion on a static pressure probe mounted on the engine hub in an F-15 airplane

An inlet static pressure (PS2) probe was mounted on the hub of an F100 engine in an F-15 airplane. Flight test results showed that for low distortion conditions, the ratio of engine-face total pressure to static pressure agreed well with previous altitude facility data. Off-schedule operation of the inlet third ramp angle caused increased distortion of the inlet airflow during steady-state flight conditions. Data are shown for inlet third ramp excursions leading to engine stall. The relationships of inlet face total to static pressure ratio as a function of several distortion descriptors are also described.

Hughes, D. L.↗
NASA NTRS1984

Effects of inlet distortion on a static pressure probe mounted on the engine hub in an F-15 airplane

Problems encountered in obtaining good engine face pressure data were studied. A single static measurement located upstream of the engine hub in the stream flow was found to provide a pressure signal suitable for engine control. Two identical probes for measuring fan inlet static (PS2) pressure were designed and mounted on the hub of the left F100-PW-100 turbofan engine installed in the F-15 test aircraft for flight evaluation. The probe is used as a static pressure sensor for a digital engine control system.

Hughes, D. L.↗
NASA NTRS1981

Comparison of three thrust calculation methods using in-flight thrust data

The gross thrust of an experimental airplane was determined by each method using the same flight maneuvers and generally the same data parameters. Coefficients determined from thrust stand calibrations for each of the three methods were then extrapolated to cruise flight conditions. The values of total aircraft gross thrust calculated by the three methods for cruise flight conditions agreed within + or - 3 percent. The disagreement in the values of thrust calculated by the different techniques manifested itself as a bias in the data. There was little scatter (0.5 percent) for the thrust levels examined in flight.

Hughes, D. L.↗
NASA NTRS1976

Dynamic test techniques - Concepts and practices

An initial investigation of dynamic flight test analysis techniques indicated that a strict, comprehensive force-moment accounting system would be necessary. An implementation of the longitudinal force-moment accounting system provided excellent results in accounting for small lift/drag and tail deflection changes. Attention is given to gross thrust calculation, instrumentation, maneuvers, and aspects of data correlation. The results of the studies demonstrate that it is possible to generate a lift/drag model which is capable of predicting performance from nearly any maneuver.

Rawlings, K., III↗
NASA NTRS1973

Steady-state and dynamic pressure phenomena in the propulsion system of an F-111A airplane

Flight tests were conducted with two F-111A airplanes to study the effects of steady-state and dynamic pressure phenomena on the propulsion system. Analysis of over 100 engine compressor stalls revealed that the stalls were caused by high levels of instantaneous distortion. In 73 percent of these stalls, the instantaneous circumferential distortion parameter, k sub theta, exhibited a peak just prior to stall higher than any previous peak. The K sub theta parameter was a better indicator of stall than the distortion factor, k sub d, and the maximum-minus-minimum distortion parameter, d, was poor indicator of stall. Inlet duct resonance occurred in both F-111A airplanes and is believed to have been caused by oscillations of the normal shock wave from an internal to an external position. The inlet performance of the two airplanes was similar in terms of pressure recovery, distortion, and turbulence, and there was good agreement between flight and wind-tunnel data up to a Mach number of approximately 1.8.

Burcham, F. W.↗
NASA NTRS1973

Pressures and temperatures on the lower surfaces of an externally blown flap system during full-scale ground tests

Full-scale ground tests of an externally blown flap system were made using the wing of an F-111B airplane and a CF700 engine. Pressure and temperature distributions were determined on the undersurface of the wing, vane, and flap for two engine exhaust nozzles (conical and daisy) at several engine power levels and engine/wing positions. The test were made with no airflow over the wing. The wing sweep angle was fixed at e6 deg; and the angle of incidence between the engine and the wing was fixed at 3 deg; and the flap was in the retracted, deflected 35 deg, and deflected 60 deg positions. The pressure load obtained by integrating the local pressures on the undersurface of the flap, F sub p was approximately three times greater at the 60 deg flap position than at the 35 deg flap position. At the 60 deg flap position, F sub p was between 40 percent and 55 percent of the engine thrust over the measured range of thrust. More than 90 percent of F sub p was contained within plus or minus 20 percent of the flap span centered around the engine exhaust centerline with both nozzle configurations. Maximum temperatures recorded on the flaps were 218 C (424 F) and 180 C (356 F) for the conical and daisy nozzles, repectively,

Hughes, D. L.↗
NASA NTRS1972

Flight-determined characteristics of an air intake system on an F-111A airplane

Flow phenomena of the F-111A air intake system were investigated over a large range of Mach number, altitude, and angle of attack. Boundary-layer variations are shown for the fuselage splitter plate and inlet entrance stations. Inlet performance is shown in terms of pressure recovery, airflow, mass-flow ratio, turbulence factor, distortion factor, and power spectral density. The fuselage boundary layer was found to be not completely removed from the upper portion of the splitter plate at all Mach numbers investigated. Inlet boundary-layer ingestion started at approximately Mach 1.6 near the translating spike and cone. Pressure-recovery distribution at the compressor face showed increasing distortion with increasing angle of attack and increasing Mach number. The time-averaged distortion-factor value approached 1300, which is near the distortion tolerance of the engine at Mach numbers above 2.1.

Hughes, D. L.↗
NASA NTRS1972

Survey of wing and flap lower-surface temperatures and pressures during full-scale ground tests of an externally blown flap system

Full-scale ground tests of an externally blown flap system were made using the wing of an F-111B airplane and a CF700 engine. Pressure and temperature distributions were determined on the undersurface of the wing, vane, and flap for two engine exhaust nozzles (conical and daisy) at several engine power and engine/wing positions. The tests were made with no airflow over the wing. The leading-edge wing sweep angle was fixed at 26 deg, the angle of incidence between the engine and the wing was fixed at 3 deg, and the tests were conducted with the flap retracted, extended and deflected 35 deg, and extended and deflected 60 deg. The integrated local pressures on the undersurface of the flap produced loads approximately three times as great at the 60 deg flap position as at the 35 deg flap position. With both nozzle configurations, more than 90 percent of the integrated pressure loads were contained within plus or minus 20 percent of the flap span centered around the engine exhaust centerline. The maximum temperature recorded on the flaps was 218 C (424 F) for the conical nozzle and 180 C (356 F) for the daisy nozzle.

Hughes, D. L.↗