Engineering Papers⌕ Search

Engineering topics

Huber, George W.

Publications and source records attributed to Huber, George W..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The Effects of Polyolefin Structure and Source on Pyrolysis-Derived Plastic Oil Composition

Seven types of plastics were pyrolyzed in a fluidized bed reactor: post-consumer recycled (PCR) high-density polyethylene (HDPE), PCR polypropylene (PP), virgin resins of varying molecular weights of HDPE, virgin resins of low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE), and (PP). Pyrolysis produced non-condensable gases (C1-C3), liquid phase products (C4-C40), and solids (C40+ and chars), with alkane, alkene, alkadiene, aromatic, and multi-cycloaromatics as the predominant compounds. Polymer structure had the greatest impact on product distribution, with minimal influence from molecular weight. Branches in polyethylene (PE) acted as thermal defects initiating degradation. Higher branch density in PE led to increased concentrations of aromatics, branched alkanes, and internal alkenes. PP and PE exhibited distinct degradation mechanisms, with PP requiring less energy for decomposition and yielding more oil. Here, pyrolysis oil from PCR HDPE and PCR PP contained a higher proportion of branched compounds. Additives in PCR plastics may promote isomerization during pyrolysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Scale-Up Studies for the Dehydration of C 4+ Alcohols into Drop-In Diesel Fuel

Herein, we demonstrate the production of liter quantities of drop-in diesel-range ethers from biomass-derived alcohols. We report scale-up resultsfor the dehydration of a mixture of C 4+ alcohols using powder and pellet zeolite Ycatalyst in continuous flow and batch reactors. The activity of zeolite Y decreaseswith the introduction of an alumina binder. Large alcohols, as well as branchedand secondary alcohols, increase the coke content over the pellet Y catalyst. Thepellet formulation had lower carbon balances and selectivity to C 10+ ethers,suggesting that the pellet formulation increases alcohol absorption and cokeproduction. Crushing the pellet Y catalyst to smaller particle sizes does notrecover the activity of zeolite Y in its powder form. Cold flow experiments showthat particle agglomeration contributes to pressure buildup in the continuous flowreactor. C 10+ ether blends can be produced in batch reactors at high alcohol conversion regimes. One liter of a diesel #2 blend wasproduced by scaling up this reaction. The final blend consists of a substantial portion of C 10+ ethers (63.7 wt %), followed by heavyunknown products (27.4 wt %). Furthermore, the final alcohol and butyl ether concentration values were 7.3 and 1.5 wt %, respectively. Theblendstock reported in this paper can satisfy diesel #2 ASTM standards for density, cloud point, flashpoint, and cetane number.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Catalytic production of δ-valerolactone (DVL) from biobased 2-hydroxytetrahydropyran (HTHP) – Combined experimental and modeling study

δ-Valerolactone (DVL) is a five-carbon (C5) cyclic ester that can undergo ring-opening polymerization to yield high-performance, biocompatible polyesters. But current market prices of C5 chemicals like DVL are very high due to poor availability of C5 feedstock in petroleum. Herein, we demonstrate a novel route to DVL synthesis via dehydrogenation of biomass-derived 2-hydroxytetrahydropyran (HTHP) over Cu/SiO 2 without the use of toxic reagents. Since HTHP exists in thermal equilibrium with 3,4-dihydropyran (DHP) via dehydration, and with 2,2’-oxybis(tetrahydropyran) and 5-(tetrahydropyran-2-yloxy)pentanal via acetalization, we have also determined the thermochemistry (ΔH rxn and ΔG rxn ) of each competing reaction using density functional theory (DFT) calculations at the M06-2X/cc-pVTZ level. Finally, by developing a kinetic model of all 8 reactions involved, we have achieved 84% selectivity to DVL at 150°C in a packed bed reactor for over 72 hours of time on stream.

42 ENGINEERING↗
DOE OSTI2024

Cast Film Production with Polyethylene Recycled from a Post-Industrial Printed Multilayer Film by Solvent-Targeted Recovery and Precipitation

The solvent-targeted recovery and precipitation (STRAP) process separates and recovers the constituent resins in multilayer plastic packaging films by selective polymer dissolution. In this work, three different experimental methods were considered to recover a polyethylene (PE) resin from a printed multilayer film by STRAP. The methods consisted of (1) a filter bag system, (2) a Soxhlet extraction, and (3) a jacketed dissolution vessel. Cast films were produced with the PE recovered from each method and were analyzed for color, mechanical properties, and number of impurities. High-quality recycled PE cast films can be produced by increasing the solvent to plastic ratio, including a filter pore size of 100 μm, and optimizing temperature control in STRAP. Furthermore, this study demonstrates that STRAP polymers can be recycled back into plastic films, enabling the potential circularity of these packaging materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (2) Poly(pentylene adipate–co–terephthalate)

Traditionally, most flexible food packaging is made of linear low-density polyethylene (LLDPE) which cannot easily be recycled, nor will it degrade in a reasonable timescale. In this work, a biobased biodegradable polyester alternative was investigated as a possible replacement for LLDPE. High molecular weight poly (pentylene adipate-co-terephthalate) with a 40/60 adipic acid/terephthalic acid mole ratio was synthesized using direct esterification and polycondensation. Glycerol and hexane-1,2,5,6-tetrol were added as branching agents to better match the structure of the LLDPE which in turn might help the ability of these materials in film-blowing. Thermal, mechanical, and rheological properties of the copolyesters were thoroughly investigated. All copolyesters had a weight-average molecular weight of over 140,000 g/mol, which is necessary for proper rheology, and were thermally stable up to 350°C. Here, the addition of branching agents led to a slight decrease in crystallinity, d-spacing, melting temperature, enthalpy of melting, stress at break, and elongation at break. However, an increase in Young's modulus and complex viscosity at high frequency were observed compared to PPeAT60 without branching agent added. Although the improved crystallinity and mechanical properties of the copolyesters made them viable for film-blowing, the slow crystallization rate creates a major challenge.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)

A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Catalytic Reduction of Esters over Zirconia-Supported Metal Catalysts

Esters are often produced as unwanted byproducts during the catalytic upgrading of ethanol to diesel fuel precursors through Guerbet coupling. Removal of esters from the product stream is important to prevent the loss of downstream catalyst activity from ester-derived carboxylic acids. In this work, we studied ester hydrogenolysis to the parent alcohols as a viable route for enhanced diesel fuel production. Specifically, we investigated the reduction of hexyl acetate in butanol over ZrO 2 -supported Ni, Co, Cu, Rh, Pd, and Pt catalysts, where Cu/ZrO 2 was the most selective catalyst for the hydrogenolysis of hexyl acetate into hexanol and ethanol. Thermodynamic analysis reveals that a 90% alcohol yield can be obtained at 200 °C, 30 bar, and a relatively high H 2 :hexyl acetate molar ratio of 480:1. Experimentally, an alcohol yield of 88% yield was obtained with a 10 wt % Cu/ZrO 2 catalyst at these conditions with a residence time of 5.4 h kg cat kmol gas –1 . Catalytic tests on the support revealed that ZrO 2 catalyzes the transesterification reaction between hexyl acetate and butanol. However, only the Cu sites can catalyze the hydrogenolysis of the esters into the final alcohols. We developed a kinetic model for our experimental results, which shows that the transesterification and hydrogenolysis reactions run at two different timescales, the former being 10 times faster than the latter. Data regression has been used to develop a model to predict the mole fraction distribution of ester hydrogenolysis products over a wide range of contact times. Cu/ZrO 2 loses half its catalytic activity after 80 h of time on stream. Modeling of deactivation data reveals that the ZrO 2 support conserves a residual activity due to external active sites, while active sites over the Cu surface deactivate at different rates. Furthermore, the catalytic conversion of esters into their parent alcohols is relevant to the production of surrogate liquid fuels since alcohols can be bimolecularly dehydrated to produce a blend of ethers with diesel fuel-like properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A Reactor Scale-Up Methodology from Lab-Scale to Pilot-Scale Operations: Numerical Modeling of THFA Dehydration to DHP in Packed-Bed Reactors

This manuscript discusses developing a model-based scale-up methodology for a successful technology transfer of gas-phase catalytic reactors from a lab-scale to a pilot-scale operation. The manuscript demonstrates the methodology for gas-phase dehydration of tetrahydrofurfuryl alcohol (THFA) to dihydropyran (DHP) process over commercial Al 2 O 3 catalysts. A two-dimensional reactor model was developed using COMSOL Multiphysics 6.1 software. The model solves heat and mass transport equations in bed-scale and particle scales simultaneously. This powerful feature enables accurate prediction of the heat and mass transfer limitations in pilot-scale reactors, if any exists. Further, the model uses isothermal lab-scale experimental data to derive and validate the reaction chemistry, flow fields and boundary conditions. The model was then scaled-up to project conversion, selectivity, yield and formation rate of DHP in a pilot-scale reactor. The results highlight the complex nature of chemistry, heat, and mass transfer effects in lab-scale and pilot-scale reactors. The model results inform the possible operational limitations of the pilot-scale reactor and design strategies to improve process efficiency. Although the scale-up approach is explained through the THFA dehydration process, the methodology is applicable to any catalytic packed-bed reactor models for a successful process scale-up.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Optimal Design of Food Packaging Considering Waste Management Technologies to Achieve Circular Economy

Plastic packaging plays a fundamental role in the food industry, avoiding food waste and facilitating food access. The increasing plastic production and the lack of appropriate plastic waste management technologies represent a threat to the environmental and human welfare. Therefore, there is an urgent need to identify sustainable packaging solutions. Circular economy (CE) promotes reducing waste and increasing recycling practices to achieve sustainability. In this work, we propose a CE framework based on multi-objective optimization, considering both economic and environmental impacts, to identify optimal packaging designs and waste management technologies. Using mixed-integer linear programming (MILP), techno-economic analysis (TEA), and life cycle assessment (LCA), this work aims to build the first steps in packaging design, informing about the best packaging alternatives and the optimal technology or technologies to process packaging waste. For the economic analysis, we consider the minimum increase in price (MIP) when adding recycling to the cost of each packaging solution, while for the environmental analysis, the greenhouse gas emissions impact was considered. A case study on ground coffee packaging is used to illustrate the proposed framework. The results demonstrate that the multilayer bag option is the most convenient when considering both the chosen economic and environmental impacts.

Life Cycle Analysis↗
DOE OSTI2024

Techno-Economic Analysis and Life Cycle Assessment of the Production of Biodegradable Polyaliphatic–Polyaromatic Polyesters

Poly(butylene-adipate terephthalate) (PBAT) is a polyaliphatic–polyaromatic polyester that is biodegradable and has found application in several markets, making it a widely produced biodegradable polymer worldwide. However, the production of PBAT is carbon-intensive, as it relies on the use of petroleum-based monomers. There is, thus, significant interest in identifying polyesters that are biodegradable and less carbon-intensive (e.g., use of biomass- derived monomers). In this work, we develop a detailed process model (and an associated database) for the production of polyaliphatic–polyaromatic polyesters including petroleum-based PBAT and biomass-derived alternatives including poly(pentylene- adipate terephthalate) and poly(pentylene-adipate furandicarboxy- late). Techno-economic analysis (TEA) reveals that the production costs of these polyesters strongly depend on monomer costs (accounting for over 90% of the total production cost) and identifies market conditions under which biomass-based polyesters can be cost-competitive to petroleum-based PBAT. Life cycle assessment (LCA) shows that biomass-derived polyesters can reduce the global warming impact of PBAT by half. Altogether, the proposed TEA/LCA model aims to provide guidance into polyesters that are most promising and help assess their overall economic and environmental performance.

42 ENGINEERING↗
DOE OSTI2024

Carbon-negative hydrogen: aqueous phase reforming (APR) of glycerol over NiPt bimetallic catalyst coupled with CO 2 sequestration

Herein we report the production of high-pressure (19.3 bar), carbon-negative hydrogen (H 2 ) from glycerol with a purity of 98.2 mol% H 2 , 1.8 mol% light hydrocarbons (mainly methane), and 400 ppm of CO. Aqueous phase reforming (APR) of 10 wt% glycerol solution was studied with a series of NiPt alumina bimetallic catalysts supported on alumina. The Ni 8 Pt 1 -450 catalyst had the highest hydrogen selectivity (95.6%) and the lowest alkanes selectivity (3.7%) of the tested catalysts. The hydrogen selectivity decreased in the order of Ni 8 Pt 1 -450 > Ni 8 Pt 1 -260 > Ni 1 Pt 1 -260 > Pt-260. The CO 2 was sequestered with CaO adsorbent which formed CaCO 3 . We measured the adsorption capacity of the CaO adsorbent at different temperatures. Life cycle analysis showed that the APR of glycerol coupled with CO 2 capture has net negative CO 2 equivalent greenhouse gas emissions. The CO 2 emissions are –9.9 kg CO 2 eq./kg H 2 and –50.1 kg CO 2 eq./kg H 2 when grid electricity and renewable electricity are used, respectively, and the CO 2 is allocated respectively to the mass of products produced. The cost of this H 2 (denoted as “green-emerald”) was estimated to be 2.4 USD per kg H 2 when grid electricity is used and 2.7 USD per kg H 2 when using renewable electricity. The cost of glycerol has the highest contribution of 1.71 USD per kg H 2 . As a result, participation in the carbon credit markets can further decrease the price of the produced H 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Production of drop-in biodiesel blendstocks via competitive acid-catalyzed dehydration reactions using ethanol oligomerization products

Ethanol can be converted into diesel fuel ethers using a three-step catalytic approach that involves ethanol oligomerization to larger alcohols, hydrogenolysis of the esters followed by dehydration of the C4 to C8 alcohols into ethers. In this paper we report results for the dehydration of a mixture of C4 – C8 alcohols using a zeolite Y catalyst in a continuous flow reactor. Mono-molecular dehydration of the alcohols produces olefins while bi-molecular dehydration of the alcohol produces ethers. Increasing the pressure increases the ether selectivity while decreasing the pressure produces more olefins. Linear alcohol feeds produce more C8+ ethers, while branched and secondary alcohols lead to more olefins. Olefin and coke selectivities increase with increasing carbon chain length of alcohols. Secondary alcohols lead to higher coke selectivities. Furthermore, ethanol/Butanol oligomerization experiments showed that the incoming dehydration feedstock can be grown to larger C6+ alcohol fractions, leading to higher yields of C10+ diesel-range ethers.

09 BIOMASS FUELS↗
DOE OSTI2024

Kinetic Study of Polyvinyl Chloride Pyrolysis with Characterization of Dehydrochlorinated PVC

In this paper, we study the kinetics of polyvinyl chloride (PVC) decomposition using a combination of experimental and computational approaches. Here, we develop a simplified kinetic model that contains only two steps: dehydrochlorination of PVC and further decomposition of the PVC residue. The model is consistent with density functional theory (DFT) calculations and experimental data. Dehydrochlorination is an autocatalytic reaction that starts with a tertiary chloride (Cl) and generates hydrogen chloride (HCl) and benzene as the main products. Benzene and HCl formation rates showed similar trends, indicating that HCl likely catalyzes a homolytic carbon-carbon (C-C) bond cleavage, which gives rise to benzene and an aliphatic fragment. We characterized the structure of dehydrochlorinated PVC (PVC residue) by using thermal gravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), and nuclear magnetic resonance spectroscopy (NMR). FTIR and NMR results indicate that the PVC residue contains 20% quaternary carbon content, indicating a high concentration of cross-linked molecules. We predict that the most probable structure in the cross-linked centers of the PVC residue is cyclohexadiene, which is supported by DFT calculations, FTIR, and NMR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Aliphatic Amines from Waste Polyolefins by Tandem Pyrolysis, Hydroformylation, and Reductive Amination

Pyrolysis of waste plastics can produce a product mixture with a high concentration of olefins (>50 wt%). The olefins, as building blocks in the petroleum industry, are potential precursors for valuable commodity chemicals with higher values (>$2000 per ton). In this work, we produce aldehydes by hydroformylation of the olefins present in pyrolysis oil from colored post-consumer recycled high-density polyethylene (PCR-HDPE). The obtained aldehydes in the oil are then converted into aliphatic amines via reductive amination with a Ru/C catalyst. The aminated oil was characterized by multiple analytical chemistry techniques including elemental analysis, nuclear magnetic resonance spectroscopy, high-resolution liquid chromatography-mass spectrometry, and gas chromatography-mass spectrometry with a Polyarc flame ionization detector. The concentration of metals in the PCR-HDPE and oil changes during the tandem processes, showing limited effects of these elements (e.g., Al, Ca, Fe, Mg, Ti, Zn) on hydroformylation and reductive amination. Additionally, we demonstrated that reductive amination of aldehydes with varied carbon numbers and branching properties can be achieved in the presence of a complex mixture, including paraffins and aromatics. The results indicate that waste plastics have the potential to serve as a renewable source for mono and di aliphatic amines, thereby diminishing reliance on fossil feedstocks as the current primary amine source.

aliphatic amines↗
DOE OSTI2024

Shear and extensional rheology of polyethylenes recycled using a solvent dissolution process

There is high market demand for increasing the viability of current plastic recycling processes. In this work rheology is used to evaluate the mechanical properties of a solvent dissolution recycled polymer compared to its virgin untreated precursor. Solvent dissolution and precipitation are used to target multi-layer, multi-component, industry films, which cannot be mechanically recycled. Polyethylene was chosen as the primary polymer of interest. Polymer thermal stability was monitored via time-resolved rheology; consecutive frequency sweeps over the course of an hour while under isothermal conditions. Additional rheological experiments were performed within the identified thermally stable conditions. Small-angle oscillatory shear was complemented with steady shear viscosity experiments over a wide range of shear rates. Extensional rheology was used to determine changes in molecular weight and cross link density. As a result, rheological characterization is supplemented with gas chromatography–mass spectrometry of the solvent wash to determine components stripped from the virgin polymers during solvent treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Catalytic conversion of post-consumer recycled high-density polyethylene oil over Zn-impregnated ZSM-5 catalysts

The catalytic conversion of post-consumer recycled high-density polyethylene (PCR-HDPE) pyrolysis oil was investigated using modified ZSM-5 zeolites, prepared under different conditions. The PCR-HDPE oil, obtained through pyrolysis at 500 °C followed by distillation at 165 °C, contained a naphtha fraction hydrocarbons suitable for catalytic upgrading. H/ZSM-5 converts PCR-HDPE naphtha fraction oil primarily into BTX, along with light paraffins and olefins. Introducing mesoporosity led to increased propylene yield at the expense of BTX. Zn impregnation onto H/ZSM-5 and H-meso/ZSM-5 enhanced BTX yield by up to 13 %. However, Zn-meso/ZSM-5 exhibited a lower BTX yield than Zn/ZSM-5 with the same Zn loadings, especially after additional steam treatment at 700 °C. Spent catalysts revealed no noticeable increase in metal contaminants such as calcium and aluminum that were present in the PCR-HDPE. Here, the Zn/ZSM-5 catalyst was stable for more than 50 h time on stream and showed promising potential for upgrading PCR-HDPE naphtha fraction oils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Design of supported organocatalysts from a biomass-derived difuran compound and catalytic assessment for lactose hydrolysis

The engineered structures and active sites of enzyme catalysts give rise to high catalytic activity and selectivity toward desired reactions. We have employed a biomass-derived difuran compound to append N-substituted maleimides with amino acid (glutamic acid) substitution by Diels–Alder reaction to mimic the chemical functional groups that comprise the active site channels in enzyme catalysts. The difunctionality of the biomass-derived difuran allows production of Diels–Alder adducts by appending two amino acid moieties to form a difunctional organocatalyst. The catalytic activity of the organocatalyst can be improved by immobilizing the organocatalyst on solid supporting materials. Accordingly, the structures of these immobilized organocatalysts can be engineered to mimic enzymatic active sites and to control the interaction between reactants, products, and transition states of catalytic reactions. Lactose hydrolysis was carried out to provide an example of industrial application of this approach to design and fabricate new supported organocatalysts as artificial enzymes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗