Engineering Papers⌕ Search

Engineering topics

Huber, George

Publications and source records attributed to Huber, George.

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Data for Carbon-negative Hydrogen: Aqueous Phase Reforming (APR) of Glycerol over NiPt Bimetallic Catalyst Coupled with CO2 Sequestration

Herein we report the production of high-pressure (19.3 bar), carbon-negative hydrogen (H2) from glycerol with a purity of 98.2 mol% H2, 1.8 mol% light hydrocarbons (mainly methane), and 400 ppm of CO. Aqueous phase reforming (APR) of 10 wt% glycerol solution was studied with a series of NiPt alumina bimetallic catalysts supported on alumina. The Ni8Pt1-450 catalyst had the highest hydrogen selectivity (95.6%) and the lowest alkanes selectivity (3.7%) of the tested catalysts. The hydrogen selectivity decreased in the order of Ni8Pt1-450 > Ni8Pt1-260 > Ni1Pt1-260 > Pt-260. The CO2 was sequestered with CaO adsorbent which formed CaCO3. We measured the adsorption capacity of the CaO adsorbent at different temperatures. Life cycle analysis showed that the APR of glycerol coupled with CO2 capture has net negative CO2 equivalent greenhouse gas emissions. The CO2 emissions are −9.9 kg CO2 eq./kg H2 and −50.1 kg CO2 eq./kg H2 when grid electricity and renewable electricity are used, respectively, and the CO2 is allocated respectively to the mass of products produced. The cost of this H2 (denoted as “green-emerald”) was estimated to be 2.4 USD per kg H2 when grid electricity is used and 2.7 USD per kg H2 when using renewable electricity. The cost of glycerol has the highest contribution of 1.71 USD per kg H2. Participation in the carbon credit markets can further decrease the price of the produced H2.

Catalysis↗
DOE OSTI2024

Mono-Ether and Alcohol Bioblendstocks to Reduce the Fuel Penalty of Mixing Controlled Compression Ignition (MCCI) Engine Aftertreatment

An integrated approach utilizing catalysis experiments, process systems engineering, fuel property modeling, and engine testing was utilized in this project to optimize the production process and composition of a #2 diesel bioblendstock produced from ethanol consisting primarily of long-chain mono-ethers. The primary objective of the project was to determine the composition and to design the production process for a bioblendstock for #2 diesel fuel with > 50% reduction in greenhouse gas emissions relative to conventional diesel fuel. The desired bioblendstock needed to be blendable with #2 diesel fuel at > 5 vol. % while still meeting ASTM D975 diesel fuel specification properties and achieving improvements in fuel properties: increased cetane number, decreased sooting, and reduced pour point and cloud point temperatures. At the same time, it needed to reduce the fuel energy penalty associated with MCCI engine aftertreatment resulting in improved system efficiency. The findings of the current project demonstrate that primary objective of the work has been met, i.e., to determine the composition and to design the production process for a bioblendstock for #2 diesel fuel with > 50% reduction in greenhouse gas emissions relative to conventional diesel fuel. Additionally, the results indicate that the property objectives (increased cetane number, reduced pour and cloud points, and reduced sooting propensity) for the designed bioblendstock composition have also been met. Engine testing performed has also confirmed that the increased reactivity of the bioblendstock can be used to improve catalyst heating operation and to reduce the fuel penalty associated with this operation mode. The fuel property results demonstrate that >5 vol.% blending is easily achieved while meeting the ASTM D975 #2 diesel fuel property specifications tested in this work, as this was achieved for a blend with 43 vol. % of the bioblendstock. The results provide a foundation for future work to scaleup the catalytic production process designed in this work, with many of the challenges and areas for improvement being identified in this work to enable economic production with low GHG lifecycle emissions.

09 BIOMASS FUELS↗
DOE OSTI2023

Data for Catalytic Strategy for Conversion of Triacetic Acid Lactone to Potassium Sorbate

This study shows a new route to produce potassium sorbate (KS) from triacetic acid lactone (TAL), which is a chemical platform that can be biologically synthesized from natural sources. Sorbic acid and its potassium salt (KS) are widely used as preservatives in foods and pharmaceuticals. Three steps are used to produce KS from TAL: 1) hydrogenation of TAL into 4-hydroxy-6-methyltetrahydro-2-pyrone (HMP), 2) dehydration of HMP to parasorbic acid (PSA), and 3) ring-opening and hydrolysis of PSA to KS. TAL can be fully hydrogenated over Ni/SiO2 to give near quantitative yields of HMP. A three-step reaction kinetics model was developed for dehydration of HMP into PSA. This model was used to show that the highest PSA yield occurs at low temperatures. An experimental PSA yield of 84.2% with respect to TAL was obtained which agreed with the prediction of the reaction kinetics model. KOH was used as a coreactant for the ring-opening hydrolysis of PSA to produce >99.9% yield of KS from PSA. Tetrahydrofuran (THF) was used to purify the TAL derived-KS (TAL-KS). The TAL-KS had a KS purity of 95.5%. The overall yield of TAL-KS with respect to TAL was calculated to be 77.3%. TAL-KS produced in this study had similar antimicrobial activities as commercial KS.

Catalysis↗
DOE OSTI2023

Catalytic upgrading of ethanol to C8+ distillate range ethers via Guerbet coupling and etherification

In this presentation we describe the catalytic approaches for conversion of ethanol into diesel fuel ethers. This involves first alcohol oligomerization, followed by acid-catalyzed dehydration. As we will show in this presentation, ethanol can be converted to higher linear and α-branched alcohols by C-C coupling reactions (ethanol oligomerization) as well as to high molecular weight esters by C-O coupling reactions with Cu/MgxAlOy (CuHT) catalysts. Alcohols may be converted to ethers via bimolecular dehydration in a subsequent step. We have identified more than 160 number of species in the products including alcohols, esters, aldehydes, ketones, and olefins. Alcohols range from C4 to C10. Both alcohols and esters follow a Schulz-Flory chain growth model. We show the relationship between the catalyst properties (BET surface area, acid and base site count and Cu loading and synthesis method) and the performance in the reactions. We also show that physical mixtures of CuHT and HT can have similar product selectivity of low loading CuHT catalysts. The selectivity towards diesel fuel precursor compounds (hereafter ‘DFPC’) increased with conversion until reaching a plateau at high ethanol conversion (~70%). Alcohol selectivity follows a Schultz-Flory distribution at all studied conversions, and that adsorbed ethanol-derived species may undergo surface oligomerization into 1-butanol and higher alcohols before desorbing in a chain-growth mechanism. Zeolite catalysts convert the C4+ alcohols into C8+ ethers in both batch and continuous flow reactors. Selectivities of up to 80% to C8+ ethers at around 70% conversion using a single pass continuous flow system are achieved. The final product feedstocks obtained from etherification have been used in technoeconomic (TEA) and lifecycle analysis (LCA), which indicate a reduction in greenhouse gas (GHG) emissions of 50% relative to conventional diesel and diesel fuel prices that are lower than biodiesel. These final feedstocks are undergoing engine testing to elucidate the physiochemical properties and compare well to diesel #2 ASTM standards.

Huber, George↗
DOE OSTI2022

Catalytic Upgrading of Ethanol to C8+ Distillate Range Ethers via Guerbet Coupling and Etherification

Guerbet coupling followed by etherification is a two step process for conversion of ethanol into distillate range molecules. This involves first alcohol oligomerization, followed by acid-catalyzed dehydration. As we will show in this presentation, ethanol can be converted to higher linear and α-branched alcohols by C-C coupling reactions (ethanol oligomerization) as well as to high molecular weight esters by C-O coupling reactions with Cu/MgxAlOy (CuHT) catalysts. Alcohols may be converted to ethers via bimolecular dehydration in a subsequent step. We have identified more than 160 number of species in the products including alcohols, esters, aldehydes, ketonces, and olefins. Alcohols range from C4 to C10. Both alcohols and esters follow a Schulz-Flory chain growth model. We show the relationship between the catalyst properties (BET surface area, acid and base site count and Cu loading and synthesis method) and the performance in the reactions. We also show that physical mixtures of CuHT and HT can have similar product selectivity of low loading CuHT catalysts. The selectivity towards diesel fuel precursor compounds (hereafter ‘DFPC’) increased with conversion until reaching a plateau at high ethanol conversion (~70%). Alcohol selectivity follows a Schultz-Flory distribution at all studied conversions, and that adsorbed ethanol-derived species may undergo surface oligomerization into 1-butanol and higher alcohols before desorbing in a chain-growth mechanism. Zeolite catalysts convert the C4+ alcohols into C8+ ethers in both batch and continuous flow reactors. Selectivities of up to 80% to C8+ ethers at around 70% conversion using a single pass continuous flow system are able to be achieved. The final product feedstocks obtained from etherification have been used in technoeconomic (TEA) and lifecycle analysis (LCA), which indicate a reduction in greenhouse gas (GHG) emissions of 50% relative to conventional diesel. These final feedstocks are undergoing engine testing to elucidate the physiochemical properties and will be compared to diesel #2 ASTM standards as a reference and will serve as a basis to improve the final bio-diesel blendstocks from etherification.

Huber, George↗
DOE OSTI2021

Data for Renewable Linear Alpha-Olefins by Base-Catalyzed Dehydration of Biologically-Derived Fatty Alcohols

Base catalysts were studied for the dehydration of fatty alcohols to linear alpha olefins (LAOs). For the gas phase dehydration of 1-octanol to 1-octene, 15% Cs/SiO2 catalyst was 56% selective at 10% conversion. Diluting a feed of C8, C10, and C14 fatty alcohols to 50% in undecane increased the selectivity to alpha olefins to 77–99%. 15% Cs/SiO2 was further investigated for the gas phase dehydration of a 4.2 g L−1 mixed C8–C14 fatty alcohol in tridecane feed and showed linear alpha olefin selectivities of 78–100% at initial conversions of 51–91% with the conversion lowering to 32–77% over 30 h. Catalytic activity was totally regenerated through calcination. A feed of biologically derived alcohols was produced with E. coli strain CM24 transformed with three plasmids (pBTRCk–pVHb–maACR, pACYC–pVHb–seFadBA, pTRC99A–pVHb–tdTER–fdh) which yielded a 5.5 g L−1 of C8–C14 fatty alcohol in tridecane. This biologically-derived feed was successfully dehydrated to linear alpha olefins over 15% Cs/SiO2 at selectivities of 60–100% with initial conversions of 35–75% which decreased to 22–55% over 30 h. Techno-economic analysis (TEA) of the integrated process for fatty alcohol production and subsequent dehydration to alpha olefins was conducted across the potential fermentation TRY (titer, rate, yield) landscape. Baseline fermentation performance resulted in a minimum product selling price (MPSP) double the market price for LAOs due to low titers and high costs associated with managing water and tridecane solvent flows through the system. However, targeted improvements in fermentation performance (e.g., achieving 40 g L−1 titer, 0.5 g L−1 h−1 productivity, 80% theoretical yield) can enable financially viable production of biologically derived LAOs.

Catalysis↗