Test beam evaluation of silicon strip modules for ATLAS phase-II strip tracker upgrade
Not Available
Engineering topics
Publications and source records attributed to Huang, Y..
Not Available
The avoidance and suppression of runaway electron (RE) generation during disruptions is of great importance for the safe operation of tokamaks. Massive gas injection is enacted to suppress the generation of REs, but the poor gas mixing efficiency and extremely high density required to suppress RE generation make the full RE suppression unreliable. The magnetic perturbations provide an alternative RE suppression during disruptions. The use of mode penetration induced by resonant magnetic perturbations (RMPs) to suppress RE generation has been investigated on the J-TEXT tokamak. For a sufficiently long mode penetration duration, robust runaway suppression has been reached during the disruptions. The m/n = 2/1 mode RMP with high amplitude excites large magnetic islands inside the plasma and leads to the large-scale destruction of magnetic surfaces during disruptions, which results in RE loss and runaway-free disruptions. The essential island width required for runaway suppression is estimated to be larger than 0.16 as the minor radius. This value might be slightly underestimated because of the misalignment between the electron cyclotron emission diagnostic and the island O-point. NIMROD simulations are used to investigate the effect of magnetic islands on RE generation during disruption, showing that the large magnetic islands have the ability to enhance RE seed loss during disruptions. RMP can excite large magnetic islands in the target plasma without tearing mode and might be a way to prevent RE generation during disruptions.
The injection of a large amount of impurities is one of the possible ways of mitigating disruption in large-scale tokamaks. The deposition of impurities at the center of the plasma is the key to the radiation of plasma energy and suppression of runaway. The interaction of the gas jet with the rational surfaces has been studied by scanning the plasma current. The experimental results show that the injection of a massive amount of argon can cool the plasma from the edge to the core region, and the cooling process is accompanied by different magnetohydrodynamic (MHD) modes when the gas jet reaches the corresponding rational surfaces. It is observed that with different edge safety factors and electron density, gas injection can induce different poloidal modes at first. Then, the poloidal mode traverses to lower m (where m is the poloidal mode number) MHD activities until a 2/1 mode is initiated and a thermal quench is started. The experimental results show that the penetration of a gas jet across the rational surfaces is faster in the plasmas with pre-existing large 2/1 tearing modes, which indicates that the 2/1 mode plays an important role in the penetration process. Disruptions triggered by supersonic molecular beam injection display a slower cooling process compared with massive gas injection, which can be divided into four stages. The dominant poloidal mode transition from m = 3 to m = 2 is associated with electron temperature recovery.
Explore the source record for details and available documents.
Here, we investigated the doping dependence of magnetic excitations in the lightly doped cuprate La 2-x Sr x CuO 4 via combined studies of resonant inelastic x-ray scattering (RIXS) at the Cu L 3 edge and theoretical calculations. With increasing doping, the magnon dispersion is found to be essentially unchanged, but the spectral width broadens and the spectral weight varies differently at different momenta. Near the Brillouin zone center, we directly observe bimagnon excitations that possess the same energy scale and doping dependence as previously observed by Raman spectroscopy. They disperse weakly in energy-momentum space, and they are consistent with a bimagnon dispersion that is renormalized by the magnon-magnon interaction at the zone center.
We present results of the timing performance studies of the optical part and front-end electronics of the time-of-flight subdetector prototype for the ATLAS Forward Proton (AFP) detector obtained during the test campaigns at the CERN-SPS test-beam facility (120 GeV π + particles) in July 2016 and October 2016. The time-of-flight (ToF) detector in conjunction with a 3D silicon pixel tracker will tag and measure protons originating in central exclusive interactions p + p → p + X + p, where the two outgoing protons are scattered in the very forward directions. The ToF is required to reduce so-called pileup backgrounds that arise from multiple proton interactions in the same bunch crossing at high luminosity. The background can fake the signal of interest, and the extra rejection from the ToF allows the proton tagger to operate at the high luminosity required for the measurement of the processes. The prototype detector uses fused silica bars emitting Cherenkov radiation as a relativistic particle passes through them. The emitted Cherenkov photons are detected by a multi-anode micro-channel plate photomultiplier tube (MCP-PMT) and processed by fast electronics.
Layered tin sulfide semiconductors are both of fundamental interest and attractive for energy conversion applications. Sn sulfides crystallize in several stable bulk phases with different Sn:S ratios (SnS 2 , Sn 2 S 3 , and SnS), which can transform into phases with a lower sulfur concentration by introduction of sulfur vacancies (V S ). How this complex behavior affects the optoelectronic properties remains largely unknown but is of key importance for understanding light-matter interactions in this family of layered materials. In this work, we use the capability to induce V S and drive a transformation between few-layer SnS 2 and SnS by electron beam irradiation, combined with in-situ cathodoluminescence spectroscopy and ab-initio calculations to probe the role of defects in the luminescence of these materials. In addition to the characteristic band-edge emission of the endpoint structures, our results show emerging luminescence features accompanying the SnS 2 to SnS transformation. Comparison with calculations indicates that the most prominent emission in SnS 2 with sulfur vacancies is not due to luminescence from a defect level but involves recombination of excitons bound to neutral V S in SnS 2 . These results provide insight into the intrinsic and defect-related optoelectronic properties of Sn chalcogenide semiconductors.
We report the discovery of two new unbound hypervelocity stars (HVSs) from the LAMOST spectroscopic surveys. They are, respectively, a B2V-type star of ∼7 M {sub ⊙} with a Galactic rest-frame radial velocity of 502 km s{sup −1} at a Galactocentric radius of ∼21 kpc and a B7V-type star of ∼4 M {sub ⊙} with a Galactic rest-frame radial velocity of 408 km s{sup −1} at a Galactocentric radius of ∼30 kpc. The origins of the two HVSs are not clear given their currently poorly measured proper motions. However, the future data releases of Gaia should provide proper motion measurements accurate enough to solve this problem. The ongoing LAMOST spectroscopic surveys are expected to yield more HVSs to form a statistical sample, providing vital constraints on understanding the nature of HVSs and their ejection mechanisms.
The dual coolant lead-lithium (DCLL) blanket concept, which is utilized in the Fusion Nuclear Science Facility (FNSF) conceptual design, is based on a helium-cooled first wall and blanket structure with RAFS (Reduced Activation Ferritic Steel) and a self-cooled LiPb breeding zone. The objective of this work is to develop a multiphysics modeling process in order to optimize the design and achieve long lifetime, maintainability, and high reliability. 3D finite element multiphysics modeling of the DCLL first wall and blanket (midplane of one sector) has been performed using COMSOL 5.2. The multiphysics aspect of the design is demonstrated via coupling of Computational Fluid Dynamics (CFD), conjugate heat transfer and solid mechanics. Both normal and off-normal loading conditions have been analyzed. The results of velocity, pressure, and temperature distributions of helium flow, as well as the primary and thermal stress of the structure were obtained. This was followed by determination of the factors of safety along three critical paths based on the ITER Structural Design Criteria for In-vessel Components (ISDC-IC). We show here that the structural design meets the ITER-ISDC design rules under both normal and off-normal operating conditions, though the safety factors under off-normal condition with 8 MPa helium pressure are marginal. Thus simple design optimization was conducted based on a parametric study on first wall dimensions to improve the design.
Next-step fusion nuclear devices require plasma-facing components that can survive a much higher neutron dose than ITER, and in many design concepts also require higher operating temperatures, higher reliability, and materials with more attractive safety and environmental characteristics. In search of first wall concepts that can withstand surface heat fluxes beyond 2 MW/m 2 , we analyzed advanced “monoblock” designs using coolants and materials that offer more attractive long-term performance. These use tungsten armor and heat sinks, similar to previous designs, but replace the coolant with helium and the coolant containment pipe with either low-activation ferritic-martensitic steel or SiC/SiC composite. The results of analysis show that helium-cooled steel can remove up to 5 MW/m 2 of steady-state surface heat flux and helium-cooled SiC/SiC can remove nearly 10 MW/m 2 while satisfying all materials and design requirements. This suggests that a He-cooled W/SiC monoblock could withstand divertor-like heat fluxes.
We explore the temporal relationship between microwave/hard X-ray (HXR) emission and Doppler velocity during the impulsive phase of a solar flare on 2014 October 27 (SOL2014-10-27) that displays a pulse on the light curves in the microwave (34 GHz) and HXR (25–50 keV) bands before the flare maximum. Imaging observation shows that this pulse mainly comes from one footpoint of a solar flare loop. The slit of the Interface Region Imaging Spectrograph ( IRIS ) stays at this footpoint during this solar flare. The Doppler velocities of Fe xxi 1354.09 Å and Si iv 1402.77 Å are extracted from the Gaussian fitting method. We find that the hot line of Fe xxi 1354.09 Å (log T ∼ 7.05) in the corona exhibits blueshift, while the cool line of Si iv 1402.77 Å (log T ∼ 4.8) in the transition region exhibits redshift, indicating explosive chromospheric evaporation. Evaporative upflows along the flare loop are also observed in the AIA 131 Å image. To our knowledge, this is the first report of chromospheric evaporation evidence from both spectral and imaging observations in the same flare. Both microwave and HXR pulses are well correlated with the Doppler velocities, suggesting that the chromospheric evaporation is driven by nonthermal electrons around this footpoint of a solar flare loop.
Three-dimensional topological insulators (3D TIs) represent states of quantum matters in which surface states are protected by time-reversal symmetry and an inversion occurs between bulk conduction and valence bands. However, the bulk-band inversion, which is intimately tied to the topologically nontrivial nature of 3D Tis, has rarely been investigated by experiments. Besides, 3D massive Dirac fermions with nearly linear band dispersions were seldom observed in TIs. Recently, a van der Waals crystal, ZrTe 5 , was theoretically predicted to be a TI. Here, we report an infrared transmission study of a high-mobility [~33,000 cm 2 /(V • s)] multilayer ZrTe 5 flake at magnetic fields (B) up to 35 T. Our observation of a linear relationship between the zero-magnetic-field optical absorption and the photon energy, a bandgap of ~10 meV and a √B dependence of the Landau level (LL) transition energies at low magnetic fields demonstrates 3D massive Dirac fermions with nearly linear band dispersions in this system. More importantly, the reemergence of the intra-LL transitions at magnetic fields higher than 17 T reveals the energy cross between the two zeroth LLs, which reflects the inversion between the bulk conduction and valence bands. Finally, our results not only provide spectroscopic evidence for the TI state in ZrTe 5 but also open up a new avenue for fundamental studies of Dirac fermions in van der Waals materials.
The millisecond-duration radio flashes known as fast radio bursts (FRBs) represent an enigmatic astrophysical phenomenon. Recently, the sub-arcsecond localization (∼100 mas precision) of FRB 121102 using the Very Large Array has led to its unambiguous association with persistent radio and optical counterparts, and to the identification of its host galaxy. However, an even more precise localization is needed in order to probe the direct physical relationship between the millisecond bursts themselves and the associated persistent emission. Here, we report very-long-baseline radio interferometric observations using the European VLBI Network and the 305 m Arecibo telescope, which simultaneously detect both the bursts and the persistent radio emission at milliarcsecond angular scales and show that they are co-located to within a projected linear separation of ≲40 pc (≲12 mas angular separation, at 95% confidence). We detect consistent angular broadening of the bursts and persistent radio source (∼2–4 mas at 1.7 GHz), which are both similar to the expected Milky Way scattering contribution. The persistent radio source has a projected size constrained to be ≲ 0.7 pc (≲0.2 mas angular extent at 5.0 GHz) and a lower limit for the brightness temperature of T{sub b}≳5×10{sup 7} K. Together, these observations provide strong evidence for a direct physical link between FRB 121102 and the compact persistent radio source. We argue that a burst source associated with a low-luminosity active galactic nucleus or a young neutron star energizing a supernova remnant are the two scenarios for FRB 121102 that best match the observed data.
Epitaxial heterostructures with precisely controlled composition and electronic modulation are of central importance for electronics, optoelectronics, thermoelectrics, and catalysis. In general, epitaxial material growth requires identical or nearly identical crystal structures with small misfit in lattice symmetry and parameters and is typically achieved by vapor-phase depositions in vacuum. We report a scalable solution-phase growth of symmetry-mismatched PbSe/Bi 2 Se 3 epitaxial heterostructures by using two-dimensional (2D) Bi 2 Se 3 nanoplates as soft templates. The dangling bond–free surface of 2D Bi 2 Se 3 nanoplates guides the growth of PbSe crystal without requiring a one-to-one match in the atomic structure, which exerts minimal restriction on the epitaxial layer. With a layered structure and weak van der Waals interlayer interaction, the interface layer in the 2D Bi 2 Se 3 nanoplates can deform to accommodate incoming layer, thus functioning as a soft template for symmetry-mismatched epitaxial growth of cubic PbSe crystal on rhombohedral Bi 2 Se 3 nanoplates. We show that a solution chemistry approach can be readily used for the synthesis of gram-scale PbSe/Bi 2 Se 3 epitaxial heterostructures, in which the square PbSe (001) layer forms on the trigonal/hexagonal (0001) plane of Bi 2 Se 3 nanoplates. We further show that the resulted PbSe/Bi 2 Se 3 heterostructures can be readily processed into bulk pellet with considerably suppressed thermal conductivity (0.30 W/m·K at room temperature) while retaining respectable electrical conductivity, together delivering a thermoelectric figure of merit ZT three times higher than that of the pristine Bi 2 Se 3 nanoplates at 575 K. Our study demonstrates a unique epitaxy mode enabled by the 2D nanocrystal soft template via an affordable and scalable solution chemistry approach. It opens up new opportunities for the creation of diverse epitaxial heterostructures with highly disparate structures and functions.
We used resonant inelastic x-ray scattering to investigate the electronic origin of orbital polarization in nickelate heterostructures taking LaTiO 3 -LaNiO 3 -3×(LaAlO 3 ), a system with exceptionally large polarization, as a model system. Furthermore, we find that heterostructuring generates only minor changes in the Ni 3d orbital energy levels, contradicting the often-invoked picture in which changes in orbital energy levels generate orbital polarization. Instead, O K-edge x-ray absorption spectroscopy demonstrates that orbital polarization is caused by an anisotropic reconstruction of the oxygen ligand hole states. This also provides an explanation for the limited success of theoretical predictions based on tuning orbital energy levels and implies that future theories should focus on anisotropic hybridization as the most effective means to drive large changes in electronic structure and realize novel emergent phenomena.
Not Available