Engineering Papers⌕ Search

Engineering topics

Huang, Tieshu

Publications and source records attributed to Huang, Tieshu.

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electrical connectors including glass seals and methods of fabrication

An electrical connector comprises an outer shell, at least one pin, and an insulating seal. The outer shell includes at least one side wall defining a cavity and having an inner surface. The outer shell is formed from electrically conductive material. The pin is positioned within the cavity and is also formed from electrically conductive material. The insulating seal is configured to provide electrical isolation of the pin and fills the cavity between the inner surface of the side wall and the pin. The insulating seal is formed from glass doped with a transition metal oxide.

Eichorst, Dennis J.↗
DOE OSTI2023

Pressureless sintering of dual-phase, high-entropy boride–carbide ceramics

Here, dual-phase, high-entropy boride–carbide ceramics were densified by pressureless sintering. Relative densities up to approximately 96% were obtained for ceramics containing about 30 vol% high-entropy boride and 70 vol% high-entropy carbide. Isostatic pressing at 200 MPa resulted in higher relative densities of both the green bodies and final ceramics compared to uniaxial pressing. The highest relative density of 96.3% was achieved for a ceramic that was isostatically pressed at 200 MPa and sintered at 2300°C for 2 h. Grain sizes of the resulting ceramics were approximately 2 µm. This is the first report of pressureless sintering of dual-phase, high-entropy boride–carbide ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Particle Migration in Large Cross-Section Ceramic On-Demand Extrusion Components

Ceramic On-Demand Extrusion (CODE) is a direct ink writing process which allows for the creation of near theoretically dense ceramic components with large cross-sections due to oil-assisted drying. Here, Yttria-stabilized zirconia (YSZ) colloidal pastes were used in CODE to produce dense (multi-road infill and ≳ 98% relative density), large continuous volume (> 1 cm 3 ), and high fidelity (nozzle diameters ≲ 1 mm) structural ceramic components with nanoparticle feedstocks (~d 50 ≲ 1 µm). However, many of these printed components underwent significant particle migration after forming. The reason for this particle migration defect was investigated using the coffee-ring effect for dilute solutions and rheological methods for dense suspensions. Modifications to the colloidal paste, such as changes in solids loading, pH, or surfactant concentration were explored as to their effectiveness to mitigate the defect. Ultimately, paste formulation and printing trade-offs are discussed with respect to the post-printing defect and as to general direct-write patterning.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fusion welding of refractory metals and ZrB 2 -SiC-ZrC ceramics

Molybdenum and a molybdenum alloy were fusion welded to ZrB2-based ceramics to determine if the electrical and thermal properties of the metals and ceramics affected their weldability. Commercial ceramic powders were hot pressed, machined into coupons, and preheated to 1600 °C before joining the ceramics to commercial metals using plasma arc welding. Weldability varied as indicated by the range of porosity observed within the fusion zones. Measured thermal and electrical properties appeared to have little to no effect on the weldability of metal-ceramic welds despite the large range of values measured across each property. Differences in melting temperatures between metal and ceramic coupons did affect weldability by changing the weld penetration depth into ceramic coupons. Finally, future studies on metal-ceramic welds are suggested to investigate the effect that work function, melt viscosity, wetting, or other properties have on weldability.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-entropy boride–carbide ceramics by sequential boro/carbothermal synthesis

We report a dual-phase high-entropy boride/carbide ceramic with fine grain size was synthesized by a sequential boro/carbothermal process. In the first step, a Hf-Nb-Ta-Ti-Zr-containing carbide was synthesized by carbothermal reduction of oxides followed by reaction of the carbide with B4C and ZrH2 to convert part of the carbide to boride. The resulting composition was ~29 vol% high-entropy boride with an average grain size of ~1.1 µm. Solid solution formation occurred at the densification temperature of 1900°C resulting in a relative density higher than 99%. The Vickers’ hardness was 26.5 ± 1.4 GPa. This is the first report of synthesizing dual-phase boride-carbide high-entropy ceramics from carbothermally synthesized, high-entropy carbide powders.

36 MATERIALS SCIENCE↗