Engineering Papers⌕ Search

Engineering topics

Huang, Jinsong

Publications and source records attributed to Huang, Jinsong.

47 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Crystallization in one-step solution deposition of perovskite films: Upward or downward?

Despite the fast progress of perovskite photovoltaic performances, understanding the crystallization and growth of perovskite films is still lagging. One unanswered fundamental question is whether the perovskite films are grown from top (air side) to bottom (substrate side) or from bottom to top despite 10 years of development. Here, by using grazing incidence x-ray diffraction and morphology characterizations, we unveil that the perovskite films prepared by one-step solution processes, including antisolvent-assisted spin coating and blade coating, follow the downward growth from intermediate phase during thermal annealing. Such a top-to-bottom downward growth is initialized by the evaporation of residual solvent from the top surface of “wet” films and is less sensitive to perovskite compositions and the wettability of underlying substrates. Addressing this fundamental question is important to understand the heterogeneity of perovskite films along the vertical direction, which markedly affects the efficiency and stability of perovskite solar cells.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultrafast Exciton Transport with a Long Diffusion Length in Layered Perovskites with Organic Cation Functionalization

Abstract Layered perovskites have been employed for various optoelectronic devices including solar cells and light‐emitting diodes for improved stability, which need exciton transport along both the in‐plane and the out‐of‐plane directions. However, it is not clear yet what determines the exciton transport along the in‐plane direction, which is important to understand its impact toward electronic devices. Here, by employing both steady‐state and transient photoluminescence mapping, it is found that in‐plane exciton diffusivities in layered perovskites are sensitive to both the number of layers and organic cations. Apart from exciton–phonon coupling, the octahedral distortion is revealed to significantly affect the exciton diffusion process, determined by temperature‐dependent photoluminescence, light‐intensity‐dependent time‐resolved photoluminescence, and density function theory calculations. A simple fluorine substitution to phenethylammonium for the organic cations to tune the structural rigidity and octahedral distortion yields a record exciton diffusivity of 1.91 cm 2 s −1 and a diffusion length of 405 nm along the in‐plane direction. This study provides guidance to manipulate exciton diffusion by modifying organic cations in layered perovskites.

Xiao, Xun↗
DOE OSTI2020

Simplified interconnection structure based on C 60 /SnO 2-x for all-perovskite tandem solar cells

The efficiencies of all-perovskite tandem devices are improving quickly. However, their complex interconnection layer (ICL) structures – with typically four or more layers deposited by different processes – limit their prospects for applications. Here, we report an ICL in all-perovskite tandem cells consisting merely of a fullerene layer and a SnO 2-x (0 60 layer is unintentionally n-doped by iodine ions from the perovskite and thus acts as an effective electron collecting layer. The SnO 2-x layer, formed by the incomplete oxidization of tin (x=1.76), has ambipolar carrier transport property enabled by the presence of a large density of Sn 2+ . The C 60 /SnO 1.76 ICL forms Ohmic contacts with both wide and narrow bandgap perovskite subcells with low contact resistivity. The ICL boosts the efficiencies of small-area tandem cells (5.9 mm 2 ) and large-area tandem cells (1.15 cm 2 ) to 24.4% and 22.2%, respectively. Lastly, the tandem cells remain 94% of its initial efficiency after continues 1-sun illumination for 1,000 hours.

14 SOLAR ENERGY↗
DOE OSTI2020

Blading Phase–Pure Formamidinium–Alloyed Perovskites for High–Efficiency Solar Cells with Low Photovoltage Deficit and Improved Stability

Currently, blade-coated perovskite solar cells (PSCs) with high power conversion efficiencies (PCEs), i.e. greater than 20%, normally employ methylammonium lead tri-iodide with a sub-optimal bandgap. Alloyed perovskites with formamidinium (FA) cation have narrower bandgap and thus enhance device photocurrent. However, FA-alloyed perovskites show low phase stability and high moisture sensitivity. Here, we report that incorporating 0.83 molar percent organic halide salts (OHs) into the perovskite inks enables phase-pure, highly crystalline FA-alloyed perovskites with extraordinary optoelectronic properties. Here, the OH molecules modulate the crystal growth, enhance the phase stability, passivate ionic defects at the surface and/or grain boundaries, and enhance the moisture stability of the perovskite film. We demonstrate a high efficiency of 22.0% under 1 sun illumination for blade-coated PSCs with an open-circuit voltage of 1.18 V, corresponding to a very small voltage deficit of 0.33 V, and significantly improved operational stability with 96% of the initial efficiency retained under one sun illumination for 500 hours.

14 SOLAR ENERGY↗
DOE OSTI2020

Resolving spatial and energetic distributions of trap states in metal halide perovskite solar cells

We report the profiling of spatial and energetic distributions of trap states in metal halide perovskite single-crystalline and polycrystalline solar cells. The trap densities in single crystals varied by five orders of magnitude, with a lowest value of 2 × 10 11 per cubic centimeter and most of the deep traps located at crystal surfaces. The charge trap densities of all depths of the interfaces of the polycrystalline films were one to two orders of magnitude greater than that of the film interior, and the trap density at the film interior was still two to three orders of magnitude greater than that in high-quality single crystals. Suprisingly, after surface passivation, most deep traps were detected near the interface of perovskites and hole transport layers, where a large density of nanocrystals were embedded, limiting the efficiency of solar cells.

14 SOLAR ENERGY↗
DOE OSTI2020

Comparative Studies of Optoelectrical Properties of Prominent PV Materials: Halide Perovskite, CdTe, and GaAs

We compare three representative high performance PV materials: halide perovskite MAPbI3, CdTe, and GaAs, in terms of photoluminescence (PL) efficiency, PL lineshape, carrier diffusion, and surface recombination and passivation, over multiple orders of photo-excitation density or carrier density appropriate for different applications. An analytic model is used to describe the excitation density dependence of PL intensity and extract the internal PL efficiency and multiple pertinent recombination parameters. A PL imaging technique is used to obtain carrier diffusion length without using a PL quencher, thus, free of unintended influence beyond pure diffusion. Our results show that perovskite samples tend to exhibit lower Shockley-Read-Hall (SRH) recombination rate in both bulk and surface, thus higher PL efficiency than the inorganic counterparts, particularly under low excitation density, even with no or preliminary surface passivation. PL lineshape and diffusion analysis indicate that there is considerable structural disordering in the perovskite materials, and thus photo-generated carriers are not in global thermal equilibrium, which in turn suppresses the nonradiative recombination. This study suggests that relatively low point-defect density, less detrimental surface recombination, and moderate structural disordering contribute to the high PV efficiency in the perovskite. This comparative photovoltaics study provides more insights into the fundamental material science and the search for optimal device designs by learning from different technologies.

14 SOLAR ENERGY↗