Engineering Papers⌕ Search

Engineering topics

Hu, Shenyang

Publications and source records attributed to Hu, Shenyang.

At least 55 records · Page 3

A quantitative phase-field model for gas bubble evolution in UO2

Due to the large formation energy of vacancies and noble gas atoms in the form of interstitials or substitutional atoms in nuclear fuel (UO2), the thermodynamic equilibrium concentrations of these species are very low in the nuclear fuel matrix even at very high temperatures, which imposes difficulties upon the quantitative study of bubble evolution via the phase-field method. In this study, a quantitative phase-field model is proposed to deal with this problem. The system’s free energy density is derived according to the principles of thermodynamics, with consideration of the elastic effect and with the use of real material parameters from experiments. The model is useful for the study of the kinetics of gas bubble growth with very dilute concentrations of vacancy and gas atoms in the matrix. This model is applied to study single bubble growth and multiple bubble growth under various concentrations of vacancy and gas atoms and at various temperatures. The elastic effect and the effects of the generation rate of vacancies and gas atoms on bubble growth are analyzed.

low defect concentration, nuclear fuel, gas bubble↗

Phase field modeling of discontinuous dynamic recrystallization in hot deformation of magnesium alloys

We have developed a quantitative phase field model of discontinuous dynamic recrystallization (PF-DDRX) for investigating grain structure evolution and its impact on mechanical response in magnesium alloy during hot deformation. A set of isothermal compression tests were conducted by Gleeble thermo-mechanical simulator and used to determine PF-DDRX model parameters such as critical stresses of recrystallization, activation energies of dislocation, grain boundaries and recrystallization grain nucleation. In the simulations, the experimentally measured average grain size and distribution were used to generate initial microstructures. The results show that the typical ‘necklace’ microstructures observed in DDRX forms at the earlier stage of recrystallization. The inhomogeneity of microstructures first increases rapidly and then decreases gradually and reaches a constant with the increase of dynamic recrystallization volume fraction. Both predicted grain structure and mechanical response are in good agreement with experimental results. This demonstrates that the model parameters determined by experimental data are reliable for the developed PF-DDRX model to predict the grain structure evolution and flow behavior of AZ80 magnesium alloy under hot deformation. This work presents a path to combine experiments and modeling to give quantitative prediction and minimize experimental cost.

magnesium alloy, Phase field method, dynamic recry↗

A phase field study of the thermal migration of gas bubbles in UO 2 nuclear fuel under temperature gradient

Phase field models are developed to study the gas bubble migration in uranium dioxide nuclear fuel in which a large temperature gradient exists during the operation. In this work, thermal diffusion mechanism for nanosized gas bubbles and vapor transport process for micron-sized gas bubbles are considered, respectively. In both cases, gas bubbles migrate to the high-temperature area. Due to the velocity difference between leading and trailing edges of the gas bubbles, nanosized gas bubbles are elongated along the temperature gradient direction when thermal diffusion is dominated. Micron-sized gas bubbles are either compressed along temperature gradient direction to form lenticular shape bubbles or elongated along temperature gradient direction, depending on the location of the gas bubbles within the fuel pellet. Initial gas bubble radius has no significant effect on the gas bubble migration velocity for both thermal diffusion and vapor transport mechanisms. We notice that the shape change of the gas bubble due to vapor transport mechanism has no significant effect on the migration velocity. Furthermore, the center cavity formation is also captured by our model which is due to the migration and accumulation of lenticular gas bubbles at the center of the fuel pellet. The modeling results compare well with experimental observations and theoretical analysis in the literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of grain structure and strain rate on dynamic recrystallization and deformation behavior: A phase field-crystal plasticity model

Herein, a phase field (PF)-crystal plasticity (CP) model has been developed to study the effects of initial grain structures, recrystallized grain orientation, and strain rates on dynamic recrystallization and deformation behavior under stress states typical of the Shear Assisted Processing and Extrusion (ShAPE) process. The model takes the geometrically necessary dislocation density as the nucleation criterion for recrystallization and minimizes the deformation energy as the driving force of recrystallized grain growth. Using this model, the effects of grain orientations and strain rates on dynamic recrystallization and deformation behavior were simulated. The results demonstrate that (1) a polycrystalline structure with the texture observed in ShAPE process has the lowest yield stress under the ShAPE stress conditions, (2) the recrystallized grains with the texture observed in ShAPE process largely soften the materials, and (3) higher shear strain rate or rotation speed results in larger magnitude of material softening.

36 MATERIALS SCIENCE↗

Ion redistributions at interfaces facilitate nucleation and growth of branched Ag 3 PO 4 polypods

Branched structures are of spectacular interest due to their improved light-harvesting, direct carrier transportation pathway, high surface area, and controllable electronic structures. Understanding their growth mechanisms and controlling factors enables the design of materials with improved functions. Interfaces of liquid-solid and air-liquid are known to change the chemical and physical properties of the liquid solution. However, their role in crystal growth, especially of branched structures, is seldom investigated. In this work we synthesized branched silver phosphate polypods in a thin layer of aqueous solution at room temperature taking advantage of the unique properties near the interfaces. The branched crystals nucleate and grow with a liquid thickness of 810 µm or below requiring the presence of both the gas-liquid and liquid-solid interfaces. The hydrophilicity of the solid substrate also facilitates nucleation and growth. Our results indicate that the synergism of long-range electric fields (ion distributions) at the interfaces promotes not only the nucleation and growth of silver phosphate but also the formation of branched structures. This work can be a reference for facilitating crystal nucleation and growth and controlling structures with specific morphologies, such as branched ones, by understanding and mimicking the properties at the interfaces.

36 MATERIALS SCIENCE↗

Hierarchical porous silicon structures with extraordinary mechanical strength as high-performance lithium-ion battery anodes

Abstract Porous structured silicon has been regarded as a promising candidate to overcome pulverization of silicon-based anodes. However, poor mechanical strength of these porous particles has limited their volumetric energy density towards practical applications. Here we design and synthesize hierarchical carbon-nanotube@silicon@carbon microspheres with both high porosity and extraordinary mechanical strength (>200 MPa) and a low apparent particle expansion of ~40% upon full lithiation. The composite electrodes of carbon-nanotube@silicon@carbon-graphite with a practical loading (3 mAh cm −2 ) deliver ~750 mAh g −1 specific capacity, <20% initial swelling at 100% state-of-charge, and ~92% capacity retention over 500 cycles. Calendered electrodes achieve ~980 mAh cm −3 volumetric capacity density and <50% end-of-life swell after 120 cycles. Full cells with LiNi 1/3 Mn 1/3 Co 1/3 O 2 cathodes demonstrate >92% capacity retention over 500 cycles. This work is a leap in silicon anode development and provides insights into the design of electrode materials for other batteries.

25 ENERGY STORAGE↗

Effects of catalyst droplets on wire growth and the resulting branched structures during VLS growth

Vapor-liquid-solid (VLS) method is vastly employed to grow hierarchical structures with unique properties. However, key questions remain, such as what controls the branched structures and what the roles of catalyst droplet size are during the growth. Here, an in-depth understanding of the kinetics of the nucleation, growth, and subsequent coalescence processes of Bi liquid catalyst droplets is provided by direct observation of PbSe branched wire growth in an environmental transmission electron microscope. This brings a kinetic control of the branch density by varying the parameters, such as temperature. In addition, the dependence of wire growth rate on the catalyst droplet size is revealed, i.e., the smaller the catalyst size the larger the wire growth rate, unlike the wire growth controlled by Gibbs-Thomson effect, possibly due to different mass transport pathways and atomic surface diffusion. These results extend the fundamental understanding of the VLS growth mechanism of branched structures and benefit the structure design of hierarchical materials with tailored properties.

36 MATERIALS SCIENCE↗

A improved equation of state for Xe gas bubbles in gamma U-Mo fuels

A monolithic fuel design based on a U-Mo alloy has been selected as the fuel type for conversion of the United States High-Performance Research Reactors (HPRRs). An issue with U-Mo monolithic fuel is the large amount of swelling that takes place during operation. The accurate prediction of fuel evolution under irradiation requires implementation of correct thermodynamic properties into mesoscale and continuum level fuel performance modeling codes. However, the thermodynamic properties of the fission gas bubbles (such as the relationship among bubble size, equilibrium Xe concentration, and bubble pressure) are not well known. This work studies Xe bubbles in ?U-Mo from a diameter of 3 nm up to 8.5 nm and from 400 K up to 700 K. The energetic relationship of Xe bubbles with regard to voids and Xe substitutional atoms is described. The transition is also determined for when a bubble becomes over-pressurized. Finally, an equation of state is fit to the pressure as a function of molar volume and temperature.

Beeler, Benjamin↗

Recrystallization and Grain Growth Simulations for Multiple-Pass Rolling and Annealing of U-10Mo

A simulation model of recrystallization and grain growth has been developed to investigate grain structure evolution during deformation and heat treatment in polycrystalline U-10wt% Mo (U-10Mo) fuel. Experimentally obtained U-10Mo microstructures were used as input for closed loop simulations of multiple rolling, intermediate heating and final annealing process. FEM calculations of deformation and Potts Model simulations of recrystallization and grain growth were used to iteratively inform each subsequent stage of simulation. Furthermore, the model was then applied to predict the grain structure evolution during multiple-pass hot rolling of U-10Mo, and benchmarked against experimentally observed U-10Mo recrystallization behavior. The results showed that our model was able to capture the coupling between deformation and recrystallization as a function of microstructure, including particle stimulated nucleation and recrystallization nucleation on grain boundaries. Additionally, we have achieved reasonable quantitative agreement with U-10Mo recrystallization and grain growth behavior.

36 MATERIALS SCIENCE↗

Alkaline earth ion exchange study in pure silica LTA zeolites using periodic first-principles calculations

Experiments show that Zeolites, such as Linde Type A (LTA), are promising materials for radioactive decontamination processes. In this work, the thermodynamic properties associated with alkaline earth ion (Ca2+, Sr2+ and Ba2+) exchange in pure silica LTA was studied using periodic first-principles calculations. The adsorption energies of alkaline earth ions compared with that of Na+ were investigated. The driving force for the alkaline earth exchange and related isotherms were calculated, and analyzed as a function of the electron chemical potential. The results demonstrate that Na+ in a pure silica LTA can completely be removed by Ba2+ and almost completely be removed by Sr2+ from a stream, but cannot be effectively exchanged by Ca2+. We also showed that electron-donating dopants should suppress the Sr2+ and Ba2+ ion exchange, and that there is a substantial preference for incorporating Ba2+ over Sr2+. Lastly, the substantial difference between the adsorption energies of the ions in an assumed vacuum and those computed in water suggests that a solvation model is needed for accurate representation of ion adsorption in an LTA zeolite.

Kocevski, Vancho↗

A Quick Screening Approach for Design of Multi-Principle Element Alloy with Solid Solution Phase

Multi-principle element alloys (MPEAs) provide an innovative way to design materials with potential applications in extreme conditions, such as high-dose irradiation in nuclear reactors, high temperatures in aeronautic and aerospace engineering, etc. However, the composition design and optimization of MPEAs are challenging due to the vast options and complexity which make traditional theory and methods insufficient or even invalid. To effectively design MPEAs, a two-parameter approach is developed based on newly proposed enthalpy and entropy-enthalpy competition parameters. This approach can not only be used to classify conventional steels, high-entropy steels (HESs), high-entropy alloys (HEAs) and amorphous alloys, but also to predict the optimal composition of MPEAs with stable solid solution (SS) phases. The optimal compositions of three sets of Fe-Mn-Cr-Co-Ni alloys are quickly screened from millions of options to form HESs or HEAs with stable SS phases. This quick screening approach can also be applied to design other alloys and facilitate the research and development of MPEAs possessing the targeted properties and economic acceptability.

Zheng, Mingjie↗

A Monte Carlo Model of Irradiation-Induced Recrystallization in Polycrystalline UMo Fuels

Experiments show that irradiation-induced recrystallization speeds up the swelling kinetics in U10wt%Mo fuels. However, recrystallization mechanisms and the effect of initial grain microstructures on recrystallization kinetics are still unclear. In this work a Monte Carlo model coupling the rate theory of defect evolution has been developed to study the irradiation-induced recrystallization. The rate theory is used to describe the spatial evolution of gas bubbles, interstitials and interstitial loops; First-Passage Kinetic Monte Carlo (FPKMC) approach is used to describe the fast and strongly anisotropic migration of interstitials, and a Cellular Automata method is used to model the formation of recrystallized grains. With the assumption that recrystallization may occur when the local interstitial loop density is larger than a given critical value, simulation results reveal that 1) recrystallized grains first nucleate on grain boundaries and the recrystallization zone front moves to the center of original coarse grains in the UMo matrix, and 2) recrystallization starts earlier in coarse polycrystalline structures, while the overall recrystallization kinetics decreases with increasing grain size. These results agree with experimental observations. The comparison of recrystallization kinetics obtained from experiments and modeling suggests that the interstitial loop accumulation leads to the recrystallization and the interstitial loop growth is suppressed inside coarse grains due to the over-pressured intra-granular gas bubbles.

Frazier, William E.↗

PIE of Cycle 13 316SS Cladding Using Aberration Corrected STEM Image and Analys

Optical, SEM and TEM analysis confirmed the presence of moderate sensitization in the 20% cold worked 316SS after the iron aluminide coating was applied. The Cr depletion occurs on the grain boundaries between the closely spaced carbides, and at the interface between the carbides and matrix. Cr depletion varied from locally along the grain boundaries, in many cases showing levels down to 15 wt%, but a few isolated regions had depletion levels down to 12.5 wt%. Optical and SEM images taken from a weld heat affected zone revealed the recrystallization occurred after an end plug cap had been welded to the coated cladding. Irradiation did not affect the carbides in a noticeable manner, but radiation-induced segregation/depletion altered the Cr depletion profiles by removing the wide Cr depletion profile, and replacing it with a much deeper, more narrow profile. Cr levels were depleted to 8-10 wt%, Ni and Si were enriched to levels of 40 wt% and 12 wt% respectively. Substantial precipitation formed in the matrix, and on line dislocations in the matrix and on grain boundary dislocations. Voids were observed in the upper region of the TPBAR where the irradiation temperature exceeds 320C. The levels of Cr depletion and Ni/Si enrichment indicate a material in a state susceptible to irradiation assisted stress corrosion cracking.

316SS cladding↗

Simulations of post-recrystallization grain growth in monolithic U–10Mo fuel processing

In this study, the Potts Model was used to simulate the post-recrystallization grain growth behavior of U-10 wt.% Mo (U-10Mo). The fabrication process for monolithic U-10Mo fuels involves multiple stages of rolling, during which spatially heterogeneous distributions of second phase particles form in the alloy microstructure. These particles can strongly affect the post-recrystallization grain growth process. Absent particle dissolution effects, U-10Mo grain growth has been observed stagnating at increasing grain size with increasing annealing temperature. In this work, we simulate this effect in the Potts Model by making adjustments to the non-physical Monte Carlo temperature. This modification was used to account for the weakening pinning effect of the second phases with elevated annealing temperature. Simulated average grain sizes and grain size distributions were compared with experimentally obtained results for 700 °C, 800 °C, and 900 °C anneals of duration up to 240 hours. These simulations achieved reasonable agreement with experimentally observed grain growth behavior, but showed narrower grain size distributions. It is believed that this disagreement originates from the formation of bands of second-phase particles during rolling. Finally, these results demonstrate the capability to evaluate the post-recrystallization grain growth behavior for U-10Mo as a function of previous homogenization, rolling, and annealing treatments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure-based model of nonlinear ultrasonic response in materials with distributed defects

Nonlinear ultrasonic technique is one of promising NDE methods for monitoring defect evolution in irradiated nuclear materials. In this work, we have studied the effect of distributed defects on nonlinear ultrasonic response, in particular, the nonlinear parameter ß from the 2nd harmonic wave. A three-dimensional microstructure-based model has been developed for investigating the dynamic interaction between distributed defects and a propagating longitudinal sound wave. Both linear and nonlinear materials are considered. It is known that the 2nd harmonic wave is generated when a monochromatic wave propagates in a nonlinear elastic material. The results show that second phase particles with elastic heterogeneity and lattice mismatch have strong impact on the nonlinear parameter ß. Lattice mismatches have more effect on the nonlinear parameter no matter they are expansion or contraction. The developed model enables one to explore the contributions of different types of defects to the nonlinear ultrasonic signals and shed light on the development of nonlinear ultrasound nondestructive detection of material defects in nuclear reactors.

Second harmonic generation, Scattered distributed ↗