Engineering Papers⌕ Search

Engineering topics

Hu, Hongqiang

Publications and source records attributed to Hu, Hongqiang.

At least 19 records

Economic and environmental feasibility of recycling flexible plastic packaging from single stream collection

As demand for plastic increases, there is an urgent need to ramp up its collection and recycling rate. This study reports results of a pilot study in the United States to recycle flexible plastic packaging (FPP) from single stream curbside collection focusing on both the economic feasibility and carbon footprint. To explore the marketability of recycled FPP, four down-stream market pathways were studied, including roof coverboard, plastic pellets, pallets, and film. In this work, results indicated that (1) the cleaning and pelletizing process at reclaimers contributed the most to the total greenhouse gas (GHG) emissions of recycled FPP products, and (2) the GHG emissions of recycled FPP products in all four pathways are lower than the comparator products. Therefore, using a higher percentage of recycled FPP substituted in a product can result in greater GHG emission reductions. All the recycled FPP products also showed favorable economics compared to their direct competitors.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Electrochemically Engineered, Highly Energy-Efficient Conversion of Ethane to Ethylene and Hydrogen below 550 °C in a Protonic Ceramic Electrochemical Cell

Ethylene is one of the largest building blocks in the petrochemical industry, mainly produced by steam cracking of ethane derived from naphtha or shale gas at high temperatures (>800 °C). Despite its technical maturity and economic competitiveness, the thermal steam cracking of ethane is highly energy-intensive. In this work, an electrochemically engineered direct conversion process of ethane to produce hydrogen and ethylene using a planar protonic ceramic membrane reactor with a bi-functional three-dimensional catalytic electrode is reported, with a single-pass ethane conversion of 40% and ethylene yield of 26.7% at 550 °C. Compared with the industrial ethane steam cracking, this method saves process energy input by 45.1% and improves process energy efficiency by 50.6%, based on comprehensive process simulation using Aspen Plus software. Further, steam electrolysis treatment under the solid oxide electrolysis cell mode can regenerate the system’s catalytic performance and significantly alleviate catalytic degradation by 74%, demonstrating high techno-economic viability.

bi-functional electrode↗

Aspenplus Model For Msw Sorting Process

Unit operations for the MSW sorting process include shredding, magnets for ferrous separation, screening, air classification, eddy current for non-ferrous separation, and near-infrared detection for plastic recovery. The MIXCINC module within Aspen Plus was selected to handle mixed solid streams containing inert (metals and glass) and non-conventional materials (paper, plastics, biomass, organic waste). The Peng-Robinson equation of state with Boston-Mathias modifications was applied to predict properties for a nonconventional solids mix. Enthalpy and density of the non-conventional materials were defined using non-conventional material properties.

Hu, Hongqiang↗

Designing an impedance-based technique for studying corrosion on cladding materials

In nuclear cladding materials, changes in structure and chemistry over the lifetime of claddings can have a significant impact on fuel and reactor performance. Currently, chemical evolution over the lifetime of the fuel and cladding materials can only be inferred using post-irradiation examination. As an alternative to post-irradiation measurements, electrochemical impedance spectroscopy (EIS) can provide an in-pile measurement of changes in chemistry in oxides and hydrides. The objective of this study is to develop an impedance based sensing technology for measuring spatial- and time-resolved in-pile changes in cladding chemistry in order to understand the mechanisms of hydride formation, hydride dealloying and associated cladding corrosion so that a mitigation strategy and technology can be developed for reactor safe operation. Two prototype impedance-based sensors were designed and assembled using Zr-4 as working electrode and Pt as counter and reference electrode. One sensor is tubular type and the other one is plate-type. These sensors will be tested in static autoclave to investigate the effects of various environmental conditions (including temperature, pressure, and water chemistry) on cladding material corrosion mechanisms. These in-situ EIS sensors would provide corrosion-layer parameters in high-temperature water, such as (1) total layer thickness, (2) the evolution of oxide structures as uniform layer dielectric or sublayer(s), and (3) the possible electrochemistry of the volume corrosion process and the solid/liquid interface, such as the cyclic nature of corrosion of Zr alloys in high-temperature water. This work was focused on electrochemical sensor development, targeting cladding oxides/hydrides under thermodynamic equilibria; characterization of samples using Kelvin probe force microscopy (SKPFM), Raman spectroscopy, and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS) to provide high-resolution co-localized characterization of zirconium oxide and metal/oxide interface.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Herbaceous Feedstock 2018 State of Technology Report

The U.S. Department of Energy (DOE) promotes the production of advanced liquid transportation fuels from lignocellulosic biomass by funding fundamental and applied research that advances the state of technology (SOT). As part of its involvement with this mission, Idaho National Laboratory (INL) completes an annual SOT report for biomass feedstock logistics. This report summarizes supply system impacts of Bioenergy Technologies Office (BETO)-funded research and development efforts at INL and elsewhere (such as the High-Tonnage Feedstock Logistics projects (Webb et al. 2013a, Webb et al. 2013b, Webb et al. 2013c, Webb and Sokhansanj 2014, Sokhansanj et al. 2014) that lead to improvements in feedstock supply systems. These include improvements to and observed performance of innovative harvest and collection methods, storage technologies, transportation and handling approaches, and advanced preprocessing technologies. Biomass quality and variability, and the interface between feedstock quality and conversion performance are key drivers in addition to delivered feedstock cost. In this report, we estimate the benefits of R&D improvements to individual supply system unit operations, and present the status of feedstock logistics technology development for converting biomass into biofuels. These analyses are supported by experimental data where possible, and help to align the SOT relative to the cost goals defined in the Multi-Year Program Plan. The 2018 Herbaceous SOT aligned feedstock logistic design with current biorefinery’s design capacity utilized by biochemical conversion platform. Currently biochemical conversion platform utilizes a 725,000 dry ton/year biorefiney design for the techno economic analysis. Hence, feedstock delivered cost in the 2018 Herbaceous SOT is calculated based on biorefinery’s 725,000 dry ton design capacity instead of 800, 000 dry ton capacity utilized in the 2017 Herbaceous SOT. Biomass availabilities in this SOT were updated to year 2018 data from the 2016 Billion-Ton Report (BT16) (DOE 2016a), with the exception of switchgrass, for which the 2018 Herbaceous SOT utilized the 2019 switchgrass availability data from BT16. The BT16 report (DOE 2016a) does not project switchgrass availability in 2018; the soonest switchgrass is available in the BT16 report is 2019. Therefore, availability of switchgrass for this analysis was that projected for 2019. The 2018 Herbaceous SOT incorporates same technologies utilized in the 2017 Herbaceous SOT. However, a sensitivity analysis is performed to understand the impact of variation of process parameters on those technologies on feedstock logistic cost. New R&D data that shows the variations of process parameters affecting process performance is incorporated in the 2018 SOT to measure the variations in delivered feedstock cost. The 2018 Herbaceous SOT has also provided projected delivered feedstock of 2022 design case based on near term technical target under BETO funded R&D project. Finally, updated biorefinery size of 725,000 dry ton/year was incorporated within least-cost formulation model to select optimal siting and depot scales during optimization of the least cost blend. This modification to the optimization algorithm allows the trade-off between the cost of increased supply radius and the savings from selecting biomass from higher producing counties to be assessed. Such optimization has also showed the economic benefit of decentralized depots in comparison to centralized preprocessing co-located with the biorefinery by decoupling the biorefinery and feedstock locations. The 2018 Herbaceous SOT report documents the current modeled cost of a herbaceous feedstock supply system (from harvest to the pretreatment reactor throat, including grower payment) for hydrocarbon fuel production via biochemical conversion, based on equipment and processes now available or potentially available in the near term. The modeled cost also considers both the required quality and the availability of the biomass resources. The 2018 Herbaceous SOT predicts a modeled delivered feedstock cost of $83.67/dry ton (2016$); this is a $0.23/dry ton (2016$) decrease from the 2017 Herbaceous SOT. The modification of biorefinery’s designed capacity and increased projected biomass availability in the same supply shed contributed to this modeled cost reduction. The least-cost formulation model to optimally site and scale local distributed preprocessing depots also contributed to the cost reduction by considering county-level grower payment and distance from the biorefinery as variables in the optimization algorithm. Sensitivity analysis on various process parameters that affect delivered feedstock cost in the 2018 Herbaceous SOT shows that the delivered cost could varies from $80.45-$88.83/dry ton. The top factors that causes such variations are: effective baling rate, bale density, hammer mill throughput, interest rate and storage dry matter loss.

09 BIOMASS FUELS↗

Evaluation of Non-electric Market Options for a Light-water Reactor in the Midwest. Light Water Reactor Sustainability program

This study has addressed the technical feasibility and economic viability of LWR hybrid system operations based on realistic market around a specific reactor site in the Upper Midwest United States within the Great Lakes Region and near an industrial center that could benefit from more direct use of nuclear energy. The diverse industrial user and the electricity grid to optimize the revenue of the nuclear plant, depending on specific day-ahead electricity-grid capacity commitments and reserve capacity agreement requirements. For this market arrangement to work, the non-grid user is sold electricity without paying grid service fees (i.e., being considered a house load). This mode of energy sharing may require approval of governing utility commissions, depending on whether the hybrid operations can affect grid supply and manufacturing, agriculture, and transportation systems in this region provides several advantages to converting a nuclear plant into a hybrid plant that produces hydrogen and other feedstock commodities, such as polyethylene or formic acid, for example. Large-scale hydrogen production can essentially service several refineries within 20-30 miles of the nuclear plant. This would results in a measurable reduction of air-pollutant emissions reduction in the region. In addition, a large, consistent supply of hydrogen would draw new industries to the area—especially other steel-reduction and ammonia plants. For example, the nation’s first synthetic-fuels plant could also be sited near this hydrogen plant to convert CO 2 collected from the several ethanol plants in the region into methanol-based chemical feedstock and biofuels. With these perspectives in mind, this study has evaluated the business case for the following hybrid plant options.

08 HYDROGEN↗

Development of an Electrochemical Impedance Instrument for Monitoring Corrosion Formation (Oxide and Hydride) on Cladding Materials

The objective of this work package is to develop electrochemical impedance spectroscopic (EIS) techniques for the in pile measurement of changes in cladding materials in coupling with model simulation and material characterization. This work package will involve the initial development of electrochemical sensing technologies for measuring spatial and time resolved changes in cladding chemistry. Specific attention will be paid to monitoring changes in monitor cladding corrosion including oxide and hydride formation and deformation. The planned work during this period was focused on cladding material zirconium alloy corrosion, oxide and hydride development, and to characterize samples using EIS under controlled gas atmosphere, atom probe tomography (APT), Raman Spectroscopy, and Synchrotron X-ray diffraction (XRD). The corrosion, including oxide and hydride of zirconium alloy samples, was tested in this study. The samples were treated at a gas environment containing 3% H2 (vol%) balanced with N2 gas at various temperatures (100 – 500°C) and different times (up to 60 hours) and were characterized by in situ EIS. After treatment, various characterization techniques were applied to measure the samples, including TGA, Ramen, XRD, and APT. This study found that impedance spectra can be affected significantly with (furnace/environment) temperature. Higher temperature resulted in higher overall impedance, and longer exposure time exerted similar effects. Proof of concept characterization of oxidized samples, including TGA, Raman, XRD, and APT, were accomplished on samples exposed to 700 oC gas environment containing 20% O2 and 80% N2. TGA provides observable breakaway and bulk oxide growth measurements. High-temperature, in-situ Raman provides observation of oxidation stress at the surface of the oxide. Additionally, a transition from tetragonal to monoclinic zirconia can be seen early in the oxidation experiment. Specifically, tetragonal-rich zirconia is seen at the metal/oxide interface, where a transition to monoclinic-rich zirconia is seen in the bulk of the oxide. It has also been confirmed that highly compressive residual stresses are seen near the metal/oxide interface. It is concluded that the transition from tetragonal to monoclinic zirconia is induced by massive shifts in stress as the oxide grows. APT has supplied evident differences in the distribution of zirconium and oxygen at the metal/oxide interface. On the pre-breakaway sample, the metastable Zr(O) region at the boundary is relatively thin, interfaced by Zr-rich (i.e., metal) and O-rich (i.e., ZrO2) on either side. In contrast, it has been seen on a post-breakaway sample that the Zr(O) metastable region is much greater in thickness, with evidence of four “zones” showing slightly contrasting composition between 49-54% Zr. In addition, it can be seen from the Zr-2.65Nb post-breakaway sample that secondary element concentrations are considerably different than bulk composition measurements show. Specifically, Nb concentration is much lower than expected, whereas Fe concentration is much higher than expected. These differences could play a role in each element’s contribution to oxide growth mechanisms, as well as causation for breakaway. Future work is focused on analyzing EIS spectra of hydride and its correlation with characterization features, finite element (FE) modeling of cladding materials, electrochemical sensor development, targeting cladding oxides/hydrides under thermodynamic equilibria, during transients and under irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Woody Feedstock 2018 State of Technology Report

The U.S. Department of Energy promotes production of advanced liquid transportation fuels from lignocellulosic biomass by funding fundamental and applied research that advances the state of technology (SOT). As part of its involvement with this overall mission, Idaho National Laboratory completes annual SOT reports for biomass feedstock logistics. The purpose of the SOTs are to provide the status of feedstock supply system technology development for biomass to biofuels, based on actual data and experimental results relative to technical targets and cost goals from specific design cases. The 2018 Woody Feedstock SOT has been separated into three individual thermochemical conversion pathways that utilize woody feedstocks: indirect liquefaction (IDL), catalytic fast pyrolysis (CFP), and algal-blend hydrothermal liquefaction (AHTL). The 2018 delivered cost for the feedstocks were found to be ${$}$63.76/dry ton, ${$}$87.82/dry ton and ${$}$70.31/dry ton, respectively (2016${$}$). In addition to the SOT analyses, projections for each pathway have been made for the year 2022. In 2022, the feedstock costs for IDL and AHTL are estimated to remain constant over the period, while the feedstock cost for CFP is projected to be reduced to ${$}$70.31/dry ton due to advancements in air classification and leaching, that will allow forest residue to be sufficiently cleaned to match or exceed the quality of clean pine.

09 BIOMASS FUELS↗

Understanding the Impacts of Biomass Blending on the Uncertainty of Hydrolyzed Sugar Yield from a Stochastic Perspective

Feedstock price and availability are key challenges for biorefinery development and biomass blending has been suggested as a route to overcome these limitations. However, the impacts of feedstock blending on the variability of yields of hydrolyzed sugar remained unclear. This study quantifies the uncertainties in the sugar yields from the blends of corn stover, switchgrass, and grass clippings by considering both variable and model uncertainties. The results indicate that feedstock blending reduces the uncertainties in sugar yields and delivers feedstock of more uniform quality. A further investigation on xxx demonstrates that the reduction in overall uncertainty is achieved by reduced compositional uncertainties of blended feedstock. Based on these results, the optimization of blending ratios was performed with respect to three objectives: (1) probability of meeting the sugar yield target; (2) expected sugar yields; and (3) sugar yield per unit feedstock expense, while satisfying constraints of feedstock availability and cost. In conclusion, the optimization method developed in this study, is readily applied to other combinations of feedstocks, biofuels production processes, and constraints.

09 BIOMASS FUELS↗

(M4CT-18IN0707093) Investigating Electrochemical Impedance Spectroscopic (EIS) Measurement of Surrogate Oxide at High Temperatures

The objective of this work package is to develop electrochemical impedance spectroscopic (EIS) techniques for the in-pile measurement of changes in solid state chemistry of fuels and materials in coupling with model simulation and material characterization. This work package will involve the initial development of electrochemical sensing technologies for measuring spatial- and time-resolved changes in fuel and cladding chemistry. Specific attention will be paid to monitoring changes in fuel stoichiometry, monitor cladding hydride formation and deformation, and cladding corrosion. The planned work during this period was focused on theoretical investigation on high temperature impedance of material, establishing experimental capabilities, including high temperature EIS under controlled gas atmosphere, atom probe tomography (APT), Raman Spectroscopy, and Synchrotron XRD. Future work will focus on starting the electrochemical sensor development, targeting the dielectric response of oxide fuels and cladding oxides/hydrides under thermodynamic equilibria, during transients, and under irradiation. Three main achievements are summarized in this report for the FY17 carry-over. First, theoretical investigation on high temperature impedance of material were conducted and spatial distribution of defects and equivalent resistivity in stoichiometric oxides under a temperature gradient were analyzed. Second, a laboratory for EIS measurement at high temperature was established and the laboratory instruction (LI) for conducting experiments was approved; and the impedance of CeO2 at 800 C was examined and its electrical conductivities were analyzed and compared with other reported data. In addition, the capabilities of advanced characterization wer established including high temperature Ramen, atom probe tomography (APT) and SEM, and samples including Zr4 and CeO2 were characterized.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Establishing New Capability of High Temperature Electrochemical Impedance Spectroscopy Techniques for Equilibrium and Kinetic Experiments

In nuclear fuel and cladding materials, changes in structure and chemistry over the lifetime of the fuel can have a significant impact on fuel and reactor performance. Currently, chemical evolution over the lifetime of the fuel can only be inferred using post-irradiation examination. As an alternative to post-irradiation measurements, electrochemical impedance spectroscopy (EIS) can provide an in-pile measurement of changes in chemistry in oxides and hydrides coupling with modeling such as finite element (FE) and other material characterization techniques such as atom probe tomography (APT), Raman spectroscopy, in-situ Transmission Electron Microscopy (TEM), and synchrotron X-ray microscopy. The objective of this work package is to develop EIS techniques for the in-pile measurement of changes in solid state chemistry of fuels and materials in coupling with model simulation and material characterization. This work package will involve the initial development of electrochemical sensing technologies for measuring spatial- and time-resolved changes in fuel and cladding chemistry. Specific attention will be paid to monitoring changes in fuel stoichiometry, monitor cladding hydride formation and deformation, and cladding corrosion. This report summarized the FY17 achievements of this work package. A laboratory was begun to set up from scratch. The laboratory place was located; necessary equipment and materials were purchased and some were delivered; laboratory instruction (LI) for conducting experiments was drafted for review; radiation level of depleted UO2 that will be investigated as the potential testing sample was valued for safety issue; a testing plan for measuring changes in stoichiometry of oxide fuels has been made and roadblocks for making measurements at high temperature have been pinpointed; in addition, collaboration with Boise State University (BSU) and Massachusetts Institute of Technology (MIT) has been established. In short, the capability of applying EIS for in-pile measurement of changes of fuels and cladding materials was initiated to be established.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Technical Assessment of Using Biomass from Methyl-bromide Treated Fields in Solid Fuel Boilers

Approximately 2,500 tons of alfalfa hay in Idaho farm fields were impacted by excessive amount of bromide (Br) from field application of methyl bromide, which makes them unsuitable for animal feed. The Idaho State Department of Agriculture (ISDA) engaged the Biomass Feedstock National User Facility (BFNUF) at the Idaho National Laboratory (INL) with an objective to evaluate the feasibility of affected alfalfa as a boiler fuel to provide thermal heat. To this end, the following tasks were conducted and accomplished: (1) alfalfa characterization, both as received and processed; (2) environment, safety and health (ES&H) monitoring associated with alfalfa processing; (3) alfalfa processing and densification; (4) combustion analysis in a lab-scale boiler.

09 BIOMASS FUELS↗