Engineering Papers⌕ Search

Engineering topics

Hsu, Y. Y.

Publications and source records attributed to Hsu, Y. Y..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Preliminary assessment of systems for deriving liquid and gaseous fuels from waste or grown organics

The overall feasibility of the chemical conversion of waste or grown organic matter to fuel is examined from the technical, economic, and social viewpoints. The energy contribution from a system that uses waste and grown organic feedstocks is estimated as 4 to 12 percent of our current energy consumption. Estimates of today's market prices for these fuels are included. Economic and social issues are as important as technology in determining the feasibility of such a proposal. An orderly program of development and demonstration is recommended to provide reliable data for an assessment of the viability of the proposal.

Graham, R. W.↗
NASA NTRS1976

A preliminary assessment of the feasibility of deriving liquid and gaseous fuels from grown and waste organics

The anticipated depletion of our resources of natural gas and petroleum in a few decades has caused a search for renewable sources of fuel. Among the possibilities is the chemical conversion of waste and grown organic matter into gaseous or liquid fuels. The overall feasibility of such a system is considered from the technical, economic, and social viewpoints. Although there are a number of difficult problems to overcome, this preliminary study indicates that this option could provide between 4 and 10 percent of the U.S. energy needs. Estimated costs of fuels derived from grown organic material are appreciably higher than today's market price for fossil fuel. The cost of fuel derived from waste organics is competitive with fossil fuel prices. Economic and social reasons will prohibit the allocation of good food producing land to fuel crop production.

Graham, R. W.↗
NASA NTRS1974

Clean fuels from biomass

The potential of growing crops as a source of fuels is examined, and it is shown that enough arable land is available in the U.S. so that, even with a modest rate of crop yield, the nation could be supplied by fuel crops. The technologies for fuel conversion are available; however, some R&D efforts are needed for scaling up design. Fuel crop economics are discussed and shown to be nonprohibitive.

Hsu, Y. Y.↗
NASA NTRS1974

Clean fuels from biomass

The feasibility of converting biomass to portable fuels is studied. Since plants synthesize biomass from H2O and CO2 with the help of solar energy, the conversion methods of pyrolysis, anaerobic fermentation, and hydrogenation are considered. Cost reduction methods and cost effectiveness are emphasized.

Hsu, Y. Y.↗
NASA NTRS1973

Self-powered mixer for pressurized containers

Mechanical stirrer, installed entirely within tank, is powered by turbine driven by discharge flow of fluid. Contents of tank are automatically mixed whenever fluid in tank is discharged. Magnetic coupling eliminates need for shaft seal, particularly in high-pressure tanks.

Hsu, Y. Y.↗
NASA NTRS1973

A visual study of radial inward choked flow of liquid nitrogen.

Data and high speed movies were acquired on pressurized subcooled liquid nitrogen flowing radially inward through a 0.0076 cm gap. The stagnation pressure ranged from 0.7 to 4 MN/sq m. Steady radial inward choked flow appears equivalent to steady choked flow through axisymmetric nozzles. Transient choked flows through the radial gap are not uniform and the discharge pattern appears as nonuniform impinging jets. The critical mass flow rate data for the transient case appear different from those for the steady case. On the mass flow rate vs pressure map, the slope and separation of the isotherms appear to be less for transient than for steady radial choked flow.

Hendricks, R. C.↗
NASA NTRS1973

A visual study of radial inward choked flow of liquid nitrogen

A visual study of the radial inward choked flow of liquid nitrogen was conducted. Data and high speed moving pictures were obtained. The study indicated the following: (1) steady radial inward choked flow seems equivalent to steady choked flow through axisymmetric nozzles, (2) transient choked flows through the radial gap are not uniform and the discharge pattern appears as nonuniform impinging jets, and (3) the critical mass flow rate data for the transient case appear different from those of the steady case.

Hendricks, R. C.↗
NASA NTRS1972

Effect of contact angle hysteresis on moving liquid film integrity.

A study was made of the formation and breakdown of a water film moving over solid surfaces (teflon, lucite, stainless steel, and copper). The flow rate associated with film formation was found to be higher than the flow rate at which film breakdown occurred. The difference in the flow rates for film formation and film breakdown was attributed to contact angle hysteresis. Analysis and experiment, which are in good agreement, indicated that film formation and film breakdown are functions of the advancing and receding angles, respectively.

Simon, F. F.↗
NASA NTRS1972

Effect of contact angle hysteresis on moving liquid film integrity

A study was made of the formation and breakdown of a water film moving over solid surfaces (teflon, lucite, stainless steel, and copper). The flow rate associated with film formation was found to be higher than the flow rate at which film breakdown occurred. The difference in the flow rates for film formation and film breakdown was attributed to contact angle hysteresis. Analysis and experiment, which are in good agreement, indicated that film formation and film breakdown are functions of the advancing and receding angles, respectively.

Simon, F. F.↗
NASA NTRS1972

A review of film boiling at cryogenic temperatures.

Film boiling occurs in the quenching of metals, the chilling of biological species, the regenerative cooling of rockets, and the cooling down of a cryogenic fuel tank. Occasionally film boiling is also found in a nuclear reactor or in a cryomagnet. Aspects of film boiling involving an unconstrained liquid mass are considered, giving attention to the evaporation time, the Leidenfrost temperature, solid-liquid contacts, the thermal properties of the solid, effects of coating or scale, wettability, the metastable condition, and the velocity effect on drops. Developments discussed with regard to pool boiling are related to vertical surfaces, film boiling from horizontal surfaces, film boiling from a horizontal cylinder, film boiling from a sphere, and film boiling of helium. Processes of film boiling in a channel are also analyzed.

Hsu, Y. Y.↗
NASA NTRS1970

A review on film boiling

Film boiling covering drops and puddles, pool boiling for various geometries and forced convective film boiling

Hsu, Y. Y.↗