Engineering topics

Hrubiak, Rostislav

Publications and source records attributed to Hrubiak, Rostislav.

11 records

DOE OSTI2024

High Pressure Melting Curve of Fe‐Si: Implication for the Thermal Properties in Mercury's Core

The motion of liquid iron (Fe) alloy materials in the outer core drives the dynamo, which generates Mercury's magnetic field. The assessment of core models requires laboratory measurements of the melting temperature of Fe alloys at high pressure. Here, we experimentally determined the melting curve of Fe9wt%Si and Fe17wt%Si up to 17 GPa using in situ and ex situ measurements of intermetallic fast diffusion that serves as the melting criterion in a large-volume press. Our determined melting slopes are comparable with previous studies up to about 17 GPa. However, when extrapolated, our melting slopes significantly deviate from previous studies at higher pressures. For Mercury's core with a model composition of Fe9wt%Si, the melting temperature-depth profile determined in our study is lower by ∼150–250 K when compared with theoretical calculations. Using the new melting curve of Fe9wt%Si and the electrical resistivity values from a previous study of Fe8.5wt%Si, we estimate that the electronic thermal conductivity of liquid Fe9wt%Si is 30 Wm −1 K −1 at the Mercury's CMB pressure of 5 GPa and 37 Wm −1 K −1 at an assumed ICB of 21 GPa, corresponding to heat flux values of 23 mWm −2 and 32 mWm −2 , respectively. These values provide new constraints on the core models.

58 GEOSCIENCES↗

DOE OSTI2024

Electrical Conductivity and Sound Velocities of Talc Under High Pressure and High Temperature Conditions and Application to the Subducting Cocos Plate

Talc is expected to be an important water carrier in Earth's upper mantle, and understanding its electrical and seismic properties under high pressure and temperature conditions is required to detect possible talc-rich regions in subduction zones imaged using geophysical observations. Here, we conducted acoustic and electrical experiments on natural talc aggregates at relevant pressure-temperature conditions. Compressional wave velocity (V p ) was measured using ultrasonic interferometry in a Paris-Edinburgh press at pressures up to 3.4 GPa and temperatures up to 873 K. Similar Vp values are obtained regardless of the initial crystallographic preferred orientation of the samples, which can be explained by talc grain reorientation during the experiment, with the (001) plane becoming perpendicular to the uniaxial compression axis. Electrical conductivity of the same starting material was determined using impedance spectroscopy in a multi-anvil press up to 6 GPa and 1263 K. Two conductivity jumps are observed, at ∼860–1025 K and ∼940–1080 K, depending on pressure, and interpreted as talc dehydroxylation and decomposition, respectively. Electrical anisotropy is observed at low temperature and decreases with increasing pressure (∼10 at 1.5 GPa and ∼2 at 3.5 GPa). Comparison of acoustic and electrical results with geophysical observations in central Mexico supports the presence of a talc-bearing layer atop the subducted Cocos plate.

Cocos plate↗

DOE OSTI2024

The ultralow viscosity of volatile-rich kimberlite magma: Implications for the water content of primitive kimberlite melts

The eruption of deeply sourced kimberlite magma offers the fastest route to bring deep-seated volatiles back to the Earth’s surface. However, the viscosity of kimberlite magma, a factor governing its migration and eruption dynamics within Earth, remains poorly constrained. We conducted synchrotron in situ falling sphere viscometry experiments to examine kimberlite magma with different volatile contents (0 to 5 wt % H 2 O and 2 to 8 wt % CO 2 ) under high pressure-temperature conditions. The results reveal that the viscosity of volatile-rich kimberlite magma is ~1 to 2 orders lower than that of mid-ocean ridge basalt (MORB) and comparable to the ultramobile pure carbonate melt. Using the measured viscosity values, we simulated the ascent and eruption process of kimberlite magma. We found that a minimum content of ~0.5 wt % water in the primitive magma is necessary to allow the ultrafast eruption process of kimberlite, thereby enabling the preservation of diamonds and high-pressure mineral inclusions transported by the magma.

58 GEOSCIENCES↗

DOE OSTI2024

Pressure-induced polyamorphic transition in CaA l 2 O 4 glass

In situ high-pressure ultrasonic velocity measurements of CaAl 2 O 4 glass reveal abrupt irreversible discontinuities in the elastic wave velocities at ~8–10 GPa. Total structure factor and pair distribution functions measured by synchrotron x-ray diffraction show a rapid change in the intermediate range structure attributed to a rearrangement of calcium ions over this narrow pressure region. Atomistic models obtained from molecular dynamics simulations reveal that this intermediate range structure is explained by a transition of Ca–O void radius distribution from a bimodal distribution with peaks at ~2.1 and ~2.4 Å to a single distribution centered at ~2.1 Å. Further, these abrupt structural changes involving the rapid increase in elastic wave velocity are markedly different to the continuous transformations observed in conventional network-forming glasses, such as SiO 2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Report on the HP-CAT Workshop-2023 held at the Advanced Photon Source

The conceptual framework and the founding partner and institutional agreements for the High Pressure Collaborative Access Team (HP-CAT) were established in late 1990’s. In the following years, core infrastructure of HP-CAT was built at sector 16 of the Advanced Photon Source (APS) and the first x-ray light was delivered on July 19, 2002 at 7:00pm – followed by an official commemoration ceremony on July 26, 2002.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Migration and accumulation of hydrous mantle incipient melt in the Earth's asthenosphere: Constraints from in-situ falling sphere viscometry measurements

The Earth's oceanic lithosphere-asthenosphere boundary (LAB) is marked by a notable decrease in seismic wave velocities and an increase in attenuation. This phenomenon is likely attributed to the accumulation of partial melt at the top of the asthenosphere. Nevertheless, the process involving the upward migration and aggregation of low-degree partial melts, highly likely to be mantle incipient melts in the asthenosphere, remains underexplored. Viscosity is a key factor controlling the flow of melts, thus in this study, we used In-situ X-ray falling sphere viscometry experiments to determine the viscosity of the mantle incipient melt containing 1.8–4.0 wt.% water at 1.5–6 GPa and 2100 K. We found that water and pressure can effectively decrease the viscosity of the mantle incipient melt. Therefore, the mantle incipient melts are highly mobile with a high segregation velocity in the deeper part of the asthenosphere. However, during ascent, their mobility diminishes due to an increase in viscosity and a decrease in water content. In conclusion, these mechanisms potentially contribute to the accumulation of partial melt at the top of the asthenosphere.

58 GEOSCIENCES↗

DOE OSTI2024

Different structural behavior of MgSiO 3 and CaSiO 3 glasses at high pressures

Knowledge of the structural behavior of silicate melts and/or glasses at high pressures provides fundamental information for discussing the nature and properties of silicate magmas in the Earth’s interior. The behavior of Si-O structures under high-pressure conditions has been widely studied, while the effect of cation atoms on the high-pressure structural behavior of silicate melts or glasses has not been well investigated. Here, in this study, we investigated the structures of MgSiO 3 and CaSiO 3 glasses up to 5.4 GPa by in situ X-ray pair distribution function measurements to understand the effect of different cations (Mg 2+ and Ca 2+ ) on high-pressure structural behavior of silicate glasses. We found that the structural behavior of MgSiO 3 and CaSiO 3 glasses are different at high pressures. The structure of MgSiO 3 glass changes by shrinking of Si-O-Si angle with increasing pressures, which is consistent with previous studies for SiO 2 and MgSiO 3 glasses. On the other hand, CaSiO 3 glass shows almost no change in Si-Si distance at high pressures, while the intensities of two peaks at ~3.0 and ~3.5 Å change with increasing pressure. The structural change in CaSiO 3 glass at high pressure is interpreted as the change in the fraction of the edge-shared and corner-shared CaO 6 -SiO 4 structures. The different high-pressure structural behavior observed in MgSiO 3 and CaSiO 3 glasses may be the origin of differences in properties, such as viscosity between MgSiO 3 and CaSiO 3 melts at high pressures. This signifies the importance of different structural behaviors due to different cations in investigations of the nature and properties of silicate magmas in Earth’s interior.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Acoustic and electrical properties of Fe-Ti oxides with application to the deep lunar mantle

The overturn of titanium-rich mantle cumulates has been invoked to explain the structure and dynamics of the Moon. These dense cumulates are stable at the core-mantle boundary (CMB) and could explain field observations inferred from geophysical studies. Here, we report acoustic and electrical experiments on natural ilmenite-rutile aggregates up to 4.5 GPa and 1920 K. Seismic velocities show a weak pressure and temperature dependence, with Vs ~ 4.2 (+/-0.2) km/s and Vp ~8.0 (+/-0.2) km/s at the CMB conditions. Conductivity increases by a factor of 10 4 from 373 to 1920 K and is >10(3) S/m above 1573 K. Seismic and electrical models for the lunar mantle based on our results, considering mixtures of Fe-Ti oxides and olivine, indicate that field velocity and conductivity estimates are reproduced satisfactorily with 3-16 vol.% Fe-Ti oxides and 20 vol.% melt. Interactions between a Ti-rich, melt-bearing layer and the adjacent core likely affect the cooling and magnetic history of the Moon.

58 GEOSCIENCES↗

DOE OSTI2023

Combined First-Principles and Experimental Investigation into the Reactivity of Codeposited Chromium–Carbon under Pressure

High-pressure synthesis in the diamond anvil cell suffers from the lack of a general approach for the control of precursor stoichiometry and homogeneity. Here, we present results from a new method we have developed that uses magnetron cosputtering to prepare stoichiometrically precise and atomically mixed amorphous films of Cr:C. Laser-heated diamond anvil cell experiments carried out on a flake of this sample at pressures between 13.5 and 24.3 GPa lead to the observation of Cr 3 C (Pnma) over the entire pressure range–in good agreement with our in-house theoretical predictions–but also reveal two other metastable phases that were not expected: a novel monoclinic chromium carbide phase and the NaCl-type CrC (Fm3̅m) phase. The unexpected stability of CrC is investigated by using first-principles methods, revealing a large stabilizing effect tied to substoichiometry at the carbon site. These results offer an important case study into the current limitations of crystal structure prediction methods with regard to phase complexity and bolster the growing need for advanced theoretical approaches that can more completely survey experimentally unexplored phase space.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

hpMCA: A Python-based Graphical Program for Energy Dispersive X-Ray Diffraction Data Collection and Analysis

Energy-dispersive X-ray diffraction (EDXD) at synchrotron beamlines is commonly used for the study of material properties under high pressure and/or high temperature. Experimenters typically rely on the availability of robust data collection and analysis at a beamline, but this has become increasingly difficult, especially with the introduction of multi-element detectors that generate complex, multi-dimensional data sets. These data sets have energy resolution, and they can also be resolved in relation to sample position, diffraction angle, or different external stimuli. We report a new Python-based graphical program, hpMCA, for EDXD data collection and analysis that streamlines the experimental process for the beamline users. The program features a user-friendly interface, capability for online viewing and analyzing data from multi-element energy-dispersive detectors, and includes features useful for working with samples under high pressure and/or high temperature, such as crystal phase identification, real-time unit cell lattice refinement, and pressure determination based on an equation of state.

data analysis software↗

DOE OSTI2023

SonicPy: a suite of programs for ultrasound pulse-echo data acquisition and analysis

Sound speed and elastic constants measurements in solids and liquids are commonly performed using the ultrasound pulse-echo technique. Recent advances have expanded the use of this technique at numerous high pressure synchrotron beamlines and offline laboratories. However, the increased experimental throughput has revealed many limitations in existing software for handling the rapid measurement and the subsequent data-reduction. Here, we report the development of a collection of computer programs for sound speed measurements using the ultrasound pulse-echo technique, compatible with stepped multi-frequency, as well as broadband-pulse, couplant-corrected methods. The programs provide a highly interactive graphical interface, enable efficient measurement, exploration and near real-time analysis of the ultrasound data, and contain features useful for working with samples under high pressure and/or high temperature. The included analysis programs can alleviate the time required for data reduction from hours to less than a minute, allowing users to make timely and informed decisions regarding the appropriate experimental parameters.

97 MATHEMATICS AND COMPUTING↗