Engineering topics

Howard, Richard T.

Publications and source records attributed to Howard, Richard T..

53 records · Page 3

NASA NTRS2002

Successful Development of an Automated Rendezvous and Capture System

During the 1990's, the Marshall Space Flight Center (MSFC) conducted pioneering research in the development of an automated rendezvous and capture/docking system for U.S. space vehicles. Development and demonstration of a rendezvous sensor was identified early in the AR&C Program as the critical enabling technology that allows automated proximity operations and docking. A first generation rendezvous sensor, the Video Guidance Sensor (VGS) was developed and successfully flown on STS 87 and again on STS 95, proving the concept of a video-based sensor. Advances in both video and signal processing technologies and the lessons learned from the two successful flight experiments provided a baseline for the development, by the MSFC, of a new generation of video based rendezvous sensor. The Advanced Video Guidance Sensor (AVGS) has greatly increased performance and additional capability for longer-range operation with a new Target designed as a direct replacement for existing ISS hemispherical reflectors. A ground demonstration of the entire system and software was successfully tested.

Roe, Fred D.↗

NASA NTRS2001

Video-Based Sensor for Robotic Position and Attitude determination

NASA's Marshall Space Flight Center (MSFC) has, for the last ten years, developed various video-based sensors for use in automated docking systems. The latest generation of sensor will operate at rates of up to 100 Hz, determining the relative position (X, Y, and Z) and attitude (Roll, Pitch, and Yaw) between the sensor and a small 3-dimensional target, making it suitable for applications in robotic sensing. The Advanced Video Guidance Sensor (AVGS) is designed to track multiple targets at different ranges and determine the position and attitude of each one. The previous generation of video sensor, the Video Guidance Sensor (VGS), was flown twice on the Space Shuttle to test its performance on orbit. One of the tests performed was determining the relative positions and attitudes between the VGS and its target, which was moved to various positions using the Remote Manipulator System (RMS). The RMS position data and VGS measured data were analyzed after the flights, with good correlation between the position and attitude data of the two data sets. The test using the RMS gives a good idea of the ability of the use of the AVGS as a sensor for end-effector position and attitude determination.

Howard, Richard T.↗

NASA NTRS2001

An Advanced Video Sensor for Automated Docking

This paper describes the current developments in video-based sensors at the Marshall Space Flight Center. The Advanced Video Guidance Sensor is the latest in a line of video-based sensors designed for use in automated docking systems. The X-33, X-34, X-38, and X-40 are all designed to be unpiloted vehicles; such vehicles will require a sensor system that will provide adequate data for the vehicle to accomplish its mission. One of the primary tasks planned for re-usable launch vehicles is to resupply the space station. In order to approach the space station in a self-guided manner, the vehicle must have a reliable and accurate sensor system to provide relative position and attitude information between the vehicle and the space station. The Advanced Video Guidance Sensor is being designed and built to meet this requirement, as well as requirements for other vehicles docking to a variety of target spacecraft. The Advanced Video Guidance Sensor is being designed to allow range and bearing information to be measured at ranges up to 2 km. The sensor will measure 6-degree-of-freedom information (relative positions and attitudes) from approximately 40 meters all the way in to final contact (approximately 1 meter range). The sensor will have a data output rate of 20 Hz during tracking mode, and will be able to acquire a target within one half of a second. The prototype of the sensor will be near completion at the time of the conference.

Howard, Richard T.↗

NASA NTRS2000

Synchronized target subsystem for automated docking systems

A synchronized target subsystem for use in an automated docking or station keeping system for docking a chase vehicle with a target vehicle wherein the chase vehicle is provided with a video camera which provides adjacent frames each having a predetermined time duration. A light source mounted on the target vehicle flashes at a frequency which has a time duration which is a multiple of the duration time of the frames, the light being on for at least one frame duration and being off for the remainder of the cycle. An image processing unit is connected to the camera for receiving signals from the camera and subtracting one of the adjacent frames from the other to detect whether the light appears in one frame, both frames or neither frame. If the target light appears in both frames or neither frame, the image processing unit feeds a signal to a timing circuit to advance the video camera one frame. This process is continued until the target light appears in one frame and not in the other, at which time the process of advancing the video camera is stopped.

Howard, Richard T.↗

NASA NTRS2000

The Video Guidance Sensor: Space, Earth, Ground, and Sea

Engineers at the Marshall Space Flight Center (MSFC) have been developing and testing video-based sensors for automated spacecraft guidance for several years. The next generation of Video Guidance Sensor (VGS) is being designed to be faster and more capable than ever. It will have applications to relative position measurement in any field of endeavor. The system works by sequentially firing two different wavelengths of laser diodes at the target (which has retroreflectors) and processing the two images. Since the target only reflects one wavelength, it shows up well in one image and not at all in the other. Because the target's dimensions are known, the relative positions and attitudes of the target and the sensor can be computed from the spots reflected from the target. The current sensor operates at 5 Hz at ranges from 1 to 110 meters with a 20 deg. field-of-view. The Video Guidance Sensor (VGS) developed over the past several years has performed well in testing and met the objective of being used as the terminal guidance sensor for an automated rendezvous and capture system. The first VGS was successfully tested in closed-loop 3-degree-of-freedom (3-DOF) tests in 1989 and then in 6-DOF open-loop tests in 1992 and closed-loop tests in 1993-4. Development and testing continued, and in 1995 approval was given to test the VGS in an experiment on the Space Shuttle. The VGS flew in 1997 and in 1998, performing well during both flight experiments. During the development and testing before, during, and after the flight experiments, numerous areas for improvement were found. The next generation of VGS is being designed to operate at up to 100 Hz tracking rates and at ranges from 0.5 to 200 meters. In addition to its use as a spacecraft guidance sensor, it could be used as an alignment aid for an operator of a remote system (giving position and attitude feedback data), as a feedback system for a robotic arm, or for automated vehicle guidance. The next generation VGS, with its higher tracking rates, smaller size, and lower power could be used in more places than the original VGS, and by using LED's instead of laser diodes, the system would be eye-safe at any range. More potential applications include aerial station keeping (keeping 2 or more autonomous aircraft within particular relative positions), under-water robotics, and the guidance of ground vehicles in predefined areas equipped with sets of targets.

Howard, Richard T.↗

NASA NTRS1999

Video Guidance Sensor: Optical Performance Predictions and Results from STS-95 Experiment

The Video Guidance Sensor is a key component of NASA's Automated Rendezvous & Capture Program. The Video Guidance Sensor Uses laser illumination of a passive target in the field of view of an on-board camera and signal processor to determine the relative position and attitude between the target and sensor. The Video Guidance Sensor flew on space shuttle mission STS-95 in November of 1998 and was a marked success. Comparisons of experimental results from that mission and theoretical models predicting the optical performance will be discussed.

Jackson, John L.↗

NASA NTRS1999

The Video Guidance Sensor- A Flight Proven Technology

The Video Guidance Sensor (VGS) flew on Shuttle mission STS-95 in October of 1998 to test the VGS functional characteristics on orbit. This was the second flight of the VGS, and during these two flights, both long range and short range data were gathered under a variety of lighting conditions, orbital exposure times, and temperatures. The flight experiment sensor was designed to operate from 1.5 meter range out to 110 meter range, with a field-of-view of 16 X 21 degrees. The VGS tracked its target at a 5 Hz rate and returned 6-degree-of-freedom information on the target's position and attitude relative to the sensor. The VGS was mounted in the Shuttle cargo bay, and its target was mounted on the Spartan spacecraft being carried on this mission. The VGS is a sensor designed to allow an automated vehicle to dock with a spacecraft equipped with a passive target. The VGS is a part of an Automated Rendezvous and Capture (AR&C) system being developed and tested by NASA. The orbital testing included operations with the target on the Shuttle's Remote Manipulator System (RMS) near the start of each flight of the VGS, long-range data (on the STS-95 flight) during the Shuttle rendezvous with the Spartan two days later, and some more RMS operations later in the mission. The data returned from the orbital testing included VGS diagnostics, acquisition, and tracking data, RMS positions, hand-held laser range data, tapes of the data from the VGS video camera, and orbital positioning data from the Spartan and the Shuttle to allow correlation of the VGS data with orbital best-estimate-of-truth data. The Video Guidance Sensor performed well in all phases of the testing, and the VGS is being incorporated into the ground testing of a complete automated rendezvous and docking system. Work on the development of the next generation VGS is continuing.

Howard, Richard T.↗

NASA NTRS1999

On Orbit Testing of the Video Guidance Sensor

The Video Guidance Sensor (VGS), part of NASA's Automated Rendezvous and Capture program, was flown on Shuttle mission STS-95 in October of 1998 to orbitally test the functional characteristics of the VGS. This was the second flight of the VGS (the first flight was in 1997 on STS-87), and this time long-range tracking data was gathered during the experiment. The flight experiment sensor was designed to operate from 1.5 meter range out to 110 meter range, with a field-of-view of 16 X 21 degrees. The VGS tracked its target at a 5 Hz rate and returned 6-degree-of-freedom information on the target's position and attitude relative to the sensor. The VGS was mounted in the Shuttle cargo bay, and its target was mounted on the Spartan spacecraft being carried on this mission. The orbital testing of the VGS included operations with the target on the Shuttle's Remote Manipulator System (RMS) at the start of the 10-day mission, long-range data during the Shuttle rendezvous with the Spartan two days later, and some more RMS operations later in the mission. The data returned from the orbital testing included VGS diagnostics, acquisition, and tracking data, RMS positions, hand-held laser range data, tapes of the data from the VGS video camera, and orbital positioning data from the Spartan and the Shuttle to allow correlation of the VGS data with orbital best-estimate-of-truth data. The Video Guidance Sensor performed well in all phases of the testing, and the VGS is being incorporated into the ground testing of a complete automated rendezvous and docking system. Work on the development of the next generation VGS is continuing

Howard, Richard T.↗

NASA NTRS1998

Video Guidance Sensor Flight Experiment Results

NASA's Marshall Space Flight Center flew on the STS-87 mission an active sensor system, the Video Guidance Sensor (VGS), to demonstrate its functioning in space and to collect performance data. The VGS was designed to provide near-range sensor data as part of an automatic rendezvous and docking system. The sensor determines the relative positions and attitudes between the active sensor and the passive target. The VGS uses laser diodes to illuminate retro-reflectors in the target, a solid-state camera to detect the return from the target, and a frame grabber and digital signal processor to convert the video information into the relative positions and attitudes. The system is designed to operate with the target within a relative azimuth of +/- 9.5 degrees and a relative elevation of +/- 7.5 degrees. The system will acquire and track the target within that field-of-view anywhere from 1.5 meters to 110 meters range, and is designed to acquire at relative attitudes of +/- 10 degrees in pitch and yaw and at any roll angle. The data is output from the sensor at 5 Hz, and the target and sensor software have been designed to permit two independent sensors to operate simultaneously (in order to allow for redundancy). The data from the flight experiment includes raw video data from the VGS camera, relative position and attitude measurements from the VGS to the target, independent hand-held laser ranges from the Shuttle Aft Flight Deck to the target, and Remote Manipulator System position data to correlate with the VGS data. The experiment was quite successful and returned much useful information. The experience gained from the design and flight of this experiment will lead to improved video sensors in the future.

Howard, Richard T.↗

NASA NTRS1998

Automatic Docking System Sensor Design, Test, and Mission Performance

The Video Guidance Sensor is a key element of an automatic rendezvous and docking program administered by NASA that was flown on STS-87 in November of 1997. The system used laser illumination of a passive target in the field of view of an on-board camera and processed the video image to determine the relative position and attitude between the target and the sensor. Comparisons of mission results with theoretical models and laboratory measurements will be discussed.

Jackson, John L.↗

NASA NTRS1996

Global Positioning System Synchronized Active Light Autonomous Docking System

A Global Positioning System Synchronized Active Light Autonomous Docking System (GPSSALADS) for automatically docking a chase vehicle with a target vehicle comprising at least one active light emitting target which is operatively attached to the target vehicle. The target includes a three-dimensional array of concomitantly flashing lights which flash at a controlled common frequency. The GPSSALADS further comprises a visual tracking sensor operatively attached to the chase vehicle for detecting and tracking the target vehicle. Its performance is synchronized with the flash frequency of the lights by a synchronization means which is comprised of first and second internal clocks operatively connected to the active light target and visual tracking sensor, respectively, for providing timing control signals thereto, respectively. The synchronization means further includes first and second Global Positioning System receivers operatively connected to the first and second internal clocks, respectively, for repeatedly providing simultaneous synchronization pulses to the internal clocks, respectively. In addition, the GPSSALADS includes a docking process controller means which is operatively attached to the chase vehicle and is responsive to the visual tracking sensor for producing commands for the guidance and propulsion system of the chase vehicle.

Howard, Richard T.↗

NASA NTRS1994

Synchronized Flashing Lights For Approach And Docking

Proposed optoelectronic system for guiding vehicle in approaching and docking with another vehicle includes active optical targets (flashing lights) on approached vehicle synchronized with sensor and image-processing circuitry on approaching vehicle. Conceived for use in automated approach and docking of two spacecraft. Also applicable on Earth to manually controlled and automated approach and docking of land vehicles, aircraft, boats, and submersible vehicles, using GPS or terrestrial broadcast time signals for synchronization. Principal advantage: optical power reduced, with consequent enhancement of safety.

Book, Michael L.↗

NASA NTRS1992

Closed-loop autonomous docking system

An autonomous docking system is provided which produces commands for the steering and propulsion system of a chase vehicle used in the docking of that chase vehicle with a target vehicle. The docking system comprises a passive optical target affixed to the target vehicle and comprising three reflective areas including a central area mounted on a short post, and tracking sensor and process controller apparatus carried by the chase vehicle. The latter apparatus comprises a laser diode array for illuminating the target so as to cause light to be reflected from the reflective areas of the target; a sensor for detecting the light reflected from the target and for producing an electrical output signal in accordance with an image of the reflected light; a signal processor for processing the electrical output signal in accordance with an image of the reflected light; a signal processor for processing the electrical output signal and for producing, based thereon, output signals relating to the relative range, roll, pitch, yaw, azimuth, and elevation of the chase and target vehicles; and a docking process controller, responsive to the output signals produced by the signal processor, for producing command signals for controlling the steering and propulsion system of the chase vehicle.

Dabney, Richard W.↗

NASA NTRS1992

Autoguidance video sensor for docking

The Automated Rendezvous and Docking system (ARAD) is composed of two parts. The first part is the sensor which consists of a video camera ringed with two wavelengths of laser diode. The second part is a standard Remote Manipulator System (RMS) target used on the Orbiter that has been modified with three circular pieces of retro-reflective tape covered by optical filters which correspond to one of the wavelengths of laser diode. The sensor is on the chase vehicle and the target is on the target vehicle. The ARAD system works by pulsing one wavelength laser diodes and taking a picture. Then the second wavelength laser diodes are pulsed and a second picture is taken. One picture is subtracted from the other and the resultant picture is thresholded. All adjacent pixels above threshold are blobbed together (X and Y centroids calculated). All blob centroids are checked to recognize the target out of noise. Then the three target spots are windowed and tracked. The three target spot centroids are used to evaluate the roll, yaw, pitch, range, azimuth, and elevation. From that a guidance routine can guide the chase vehicle to dock with the target vehicle with the correct orientation.

Book, Michael L.↗

NASA NTRS1991

Standard remote manipulator system docking target augmentation for automated docking

A docking target is provided for use in automated docking of a first vehicle on which the target is located. The target comprises a pair of laterally extending arm portions lying in substantially the same plane and a central post extending outwardly from the plane of the arm portions. At least three reflectors are located on the target. Two of the reflectors are located at the outboard ends of the arms portions and another reflector is located at the end of the central post. In an important embodiment, the reflectors comprise individual pieces of retroreflective tape. The reflectors, when viewed from the front of the target, are aligned along the longitudinal center line of the target, and can take a number of different shapes including circular or square.

Dabney, Richard W.↗

NASA NTRS1991

Design and fabrication of an autonomous rendezvous and docking sensor using off-the-shelf hardware

NASA Marshall Space Flight Center (MSFC) has developed and tested an engineering model of an automated rendezvous and docking sensor system composed of a video camera ringed with laser diodes at two wavelengths and a standard remote manipulator system target that has been modified with retro-reflective tape and 830 and 780 mm optical filters. TRW has provided additional engineering analysis, design, and manufacturing support, resulting in a robust, low cost, automated rendezvous and docking sensor design. We have addressed the issue of space qualification using off-the-shelf hardware components. We have also addressed the performance problems of increased signal to noise ratio, increased range, increased frame rate, graceful degradation through component redundancy, and improved range calibration. Next year, we will build a breadboard of this sensor. The phenomenology of the background scene of a target vehicle as viewed against earth and space backgrounds under various lighting conditions will be simulated using the TRW Dynamic Scene Generator Facility (DSGF). Solar illumination angles of the target vehicle and candidate docking target ranging from eclipse to full sun will be explored. The sensor will be transportable for testing at the MSFC Flight Robotics Laboratory (EB24) using the Dynamic Overhead Telerobotic Simulator (DOTS).

Grimm, Gary E.↗

NASA NTRS1991

Video guidance sensor for autonomous capture

A video-based sensor has been developed specifically for the close-range maneuvering required in the last phase of autonomous rendezvous and capture. The system is a combination of target and sensor, with the target being a modified version of the standard target used by the astronauts with the Remote Manipulator System (RMS). The system, as currently configured, works well for autonomous docking maneuvers from approximately forty feet in to soft-docking and capture. The sensor was developed specifically to track and calculate its position and attitude relative to a target consisting of three retro-reflective spots, equally spaced, with the center spot being on a pole. This target configuration was chosen for its sensitivity to small amounts of relative pitch and yaw and because it could be used with a small modification to the standard RMS target already in use by NASA.

Howard, Richard T.↗