Engineering Papers⌕ Search

Engineering topics

Horio, M.

Publications and source records attributed to Horio, M..

Band-dependent superconducting gap in SrFe 2 (As 0.65 P 0.35 ) 2 studied by angle-resolved photoemission spectroscopy

The isovalent-substituted iron pnictide compound SrFe 2 (As 1– x P x ) 2 exhibits multiple evidence for nodal superconductivity via various experimental probes, such as the penetration depth, nuclear magnetic resonance and specific heat measurements. The direct identification of the nodal superconducting (SC) gap structure is challenging, partly because the presence of nodes is not protected by symmetry but instead caused by an accidental sign change of the order parameter, and also because of the three-dimensionality of the electronic structure. We have studied the SC gaps of SrFe 2 (As 0.65 P 0.35 ) 2 in three-dimensional momentum space by synchrotron and laser-based angle-resolved photoemission spectroscopy. The three hole Fermi surfaces (FSs) at the zone center have SC gaps with different magnitudes, whereas the SC gaps of the electron FSs at the zone corner are almost isotropic and k z -independent. As a possible nodal SC gap structure, we propose that the SC gap of the outer hole FS changes sign around the Z-X [(0, 0, 2 π ) – ( π , π , 2 π )] direction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Unusual nodal behaviors of the superconducting gap in the iron-based superconductor Ba ( F e 0.65 R u 0.35 ) 2 A s 2 : Effects of spin-orbit coupling

Here we have investigated the superconducting (SC) gap on hole Fermi surfaces (FSs) of optimally substituted Ba (Fe 0.65 Ru 0.35 ) 2 As 2 by angle-resolved photoemission spectroscopy (APRES) using bulk-sensitive 7 eV laser and synchrotron radiation. It was found that, whereas the gap is isotropic in the k x - k y plane, the gap magnitudes of two resolved hole FSs show similar k z dependences and decrease as k z approaches ~ 2 π/c (i.e., around the Z point), unlike the other Fe-based superconductors reported so far, where the SC gap of only one hole FS shows a strong k z dependence. This unique gap structure can be understood in the scenario that the d z ₂ orbital character is mixed into both hole FSs due to finite spin-orbit coupling (SOC) and is reproduced by calculation within the random phase approximation including the SOC.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fluidized bed combustor modeling

A general mathematical model for the prediction of performance of a fluidized bed coal combustor (FBC) is developed. The basic elements of the model consist of: (1) hydrodynamics of gas and solids in the combustor; (2) description of gas and solids contacting pattern; (3) kinetics of combustion; and (4) absorption of SO2 by limestone in the bed. The model is capable of calculating the combustion efficiency, axial bed temperature profile, carbon hold-up in the bed, oxygen and SO2 concentrations in the bubble and emulsion phases, sulfur retention efficiency and particulate carry over by elutriation. The effects of bed geometry, excess air, location of heat transfer coils in the bed, calcium to sulfur ratio in the feeds, etc. are examined. The calculated results are compared with experimental data. Agreement between the calculated results and the observed data are satisfactory in most cases. Recommendations to enhance the accuracy of prediction of the model are suggested.

Horio, M.↗

Simulation of fluidized bed combustors. I - Combustion efficiency and temperature profile

A chemical engineering analysis is made of fluidized-bed combustor (FBC) performance, with FBC models developed to aid estimation of combustion efficiency and axial temperature profiles. The FBC is intended for combustion of pulverized coal and a pressurized FBC version is intended for firing gas turbines by burning coal. Transport phenomena are analyzed at length: circulation, mixing models, drifting, bubble wake lift, heat transfer, division of the FB reactor into idealized mixing cells. Some disadvantages of a coal FBC are pointed out: erosion of immersed heat-transfer tubing, complex feed systems, carryover of unburned coal particles, high particulate emission in off-streams. The low-temperature bed (800-950 C) contains limestone, and flue-gas-entrained SO2 and NOx can be kept within acceptable limits.

Horio, M.↗