Engineering PapersSearch

Engineering topics

Holt, J. W.

Publications and source records attributed to Holt, J. W..

The Geographic Distribution of Boulder Halo Craters at Mid-to-High Latitudes on Mars

Extensive evidence exists for ground ice at mid-to-high latitudes on Mars, including results from neutron spectroscopy [1-3], thermal properties [4-5], geomorphology [e.g., 6-9], and the in situ observations of Mars Phoenix [10]. This ground ice has been hypothesized to be emplaced diffusively and fill pores [11], or to have accumulated by ice and dust deposition that draped or mantled the terrain [7, 12]. These two processes are not mutually exclusive; both potentially have occurred on Mars [5]. One of the landforms found in areas where ground ice is common on Mars are boulder halo craters [e.g., 13-15] (Figure 1), which are topographically muted impact craters that are filled by ice-rich regolith. They are outlined by boulders that trace a circular outline of the original crater rim. Boulder halos generally have distinctly higher boulder densities than the surrounding background plains and have few boulders in their interiors. The mechanism of boulder halo crater formation is somewhat uncertain. Our working model is that an impact event occurs with sufficient size to excavate to a depth greater than the boulder-poor, ice-rich soils. Excavated boulders are deposited around the crater's rim and in its proximal ejecta. Quite rapidly [14], the crater becomes infilled by icy soil. Rather than being buried, boulders in the halo remain at the surface, perhaps be-cause they 'float' relative to finer-grained materials [14, 16]. Regardless of the details of this process, the life-time of boulders at the surface is much greater than the timescale needed to remove most of the craters' topography. Physical weathering of rocks must be greatly out-paced by crater infilling (the opposite of what is typical, e.g., on the Moon [17]). The rapidity of this infilling is easiest to understand if icy mantling material is deposited and accumulates, rather than simply being added by pore filling of soils. If this model is correct, boulder halos only form when they excavate rock-producing materials from beneath the upper surface. Thus, the distribution and size of craters that result in boulders halos may provide in-sight into the thickness of the ice-rich surface layer in different locations. Note that this thickness is necessarily that of the ice-rich layer at the time of impact, not at present. This study is an initial survey of boulder halo crater locations in the 50deg to 80degN and 50deg to 80degS latitude bands on Mars.

Ice

Surface Clutter Removal in Airborne Radar Sounding Data from the Dry Valleys, Antarctica

We have collected roughly 1,000 line-km of airborne radar sounding data over glaciers, rock/ice glaciers, permafrost, subsurface ice bodies, ice-covered saline lakes, and glacial deposits in Taylor and Beacon Valley. These data are being analyzed in order to develop techniques for discriminating between subsurface and off-nadir echoes and for detecting and characterizing subsurface interfaces. The identification of features on Mars exhibiting morphologies consistent with ice/rock mixtures, near-surface ice bodies and near-surface liquid water, and the importance of such features to the search for water on Mars, highlights the need for appropriate terrestrial analogs and analysis techniques in order to prepare for radar sounder missions to Mars. Climatic, hydrological, and geological conditions in the Dry Valleys of Antarctica are analogous in many ways to those on Mars. A crucial first step in the data analysis process is the discrimination of echo sources in the radar data. The goal is to identify all returns from the surface of off-nadir topography in order to positively identify subsurface echoes. This process will also be critical for radar data that will be collected in areas of Mars exhibiting significant topography, so that subsurface echoes are identified unambiguously. The positive detection and characterization of subsurface (including sub-ice) water is a primary goal of NASA's Mars exploration program. Our data over the Dry Valleys provides an opportunity to implement techniques we are developing to accomplish these goals.

Holt, J. W.

Echo Source Discrimination in Airborne Radar Sounding Data for Mars Analog Studies, Dry Valleys, Antarctica

The recent identification of features on Mars exhibiting morphologies consistent with ice/rock mixtures, near-surface ice bodies and near-surface liquid water [1,2], and the importance of such features to the search for water on Mars, highlights the need for appropriate terrestrial analogs in order to prepare for upcoming radar missions targeting these and other water-related features. Climatic, hydrological, and geological conditions in the McMurdo Dry Valleys of Antarctica are analogous in many ways to those on Mars, and a number of ice-related features in the Dry Valleys may have direct morphologic and compositional counterparts on Mars.

Holt, J. W.

Attaching Metal Fasteners to Silica Tiles

Stress distributed so high load borne. Fastener bonded in densified hole or captured in plug of similar refractory material, which in turn bonded in hole in parent tile. Plug or bonding distributes mechanical load from fastener to broad region surrounding fastener, reducing local stress concentration and likelihood of breakage. Bonded-plug method has been successful in attaching mechanical fasteners to porous silica refractory tiles used on outer surface of Space Shuttle orbiter.

Holt, J. W.

Bonding Heat-Resistant Fabric to Tile

Acid etching, densification, and silica cement ensure strong bond. Key step in preparation for bonding to glazed tile is etching quartz fabric and tile with acid. This increases adhesion of silica cement used to form bond. Procedures use high-temperature materials exclusively and therefore suitable for securing flexible seals and heat barriers around doors and viewing ports in furnaces and kilns.

Holt, J. W.

High Temperature Filler for Tile Gaps

Gaps between ceramic tiles filled with ceramic-coated fabric that withstands temperatures as high as 2,000 degrees F (1,300 degrees C). Reusable high-temperature gap filler is made of fabric coated with ceramic slurry and bonded in place with room-temperature-vulcanized adhesive. Procedure used in kilns and furnaces.

Holt, J. W.

Improving Surface Strength of Insulating Tiles

Procedure for improving tile resistance to impact damage described in new report on tile densification. Developed for Space Shuttle reusable surface insulations, procedure has potential application when space restrictions necessitate thin layers of insulation with low thermal conductivity. Examples are advanced heat engines, such as adiabatic diesel and automotive gas turbine, as well as fast-heating high-temperature ovens.

Holt, J. W.

Vacuum Head Removes Sanding Dust

Vacuum sander prevents sanding dust from entering a work area, since dust particles are drawn off as quickly as they are produced. Tool is useful where dust presents health hazards, interferes with such processes as semiconductor manufacture, or could destroy wet paint or varnish finishes. Could be used to sand such materials as lead paint.

Bengle, C. G.

Attachment system for silica tiles

An improved method for markedly increasing the bond strength between a rigid, porous refractory material and non-rigid substrate by densifying the face of the rigid material opposing the substrate is discussed. Densification is accomplished by wetting the refractory material and then impregnating it with a composite slurry having a particle size to fill voids of the porous material.

Dotts, R. L.

Method for repair of thin glass coatings

A method of repairing cracks or damaged areas in glass, in particular, glass coatings provided on tile. The method includes removing the damaged area using a high speed diamond burr drilling out a cavity that extends slightly into the base material of the tile. All loose material is then cleaned from the drilled out cavity and the cavity is filled adjacent the upper surface of the coating with a filler material including chopped silica fibers mixed with a binder. The filler material is packed into the cavity and a repair coating is applied by means of a brush or sprayed thereover. The repair includes borosilicate suspended in solution. Heat is applied at approximately 2100 F. for approximately five minutes for curing the coating, causing boron silicide particles of the coating to oxidize forming a very fluid boron-oxide rich glass which reacts with the other frits to form an impervious, highly refractory layer.

Holt, J. W.

"Densified" tiles form stronger bonds

Application of colloidal silica more than doubles bond strength of ceramic tile/substrate attachments. "Densification" process strengthens surface where tile attaches to felt strain-isolator pad, redistributing stresses and preventing failures at that point. First, isopropyl alcohol is applied to bottom tile surface. Second, aqueous mixture of cementing colloidal silica and reinforcing ball-milled silica particles is painted on tile. Finally, after drying, tile is rewaterproofed by exposure to vapors or methyltrimethoxysilane and acetic acid.

Dotts, R. L.

Mobile glazing unit

Unit programs thermal cycle from 100 to 2,300 F for firing ceramic gglaze coatings on refractory surfaces in any attitude and position. Device includes control console, heater assembly, protective cover, and manipulator boom; boom places heater next to surface to be fired. Unit is industrially useful for in situ repair of ceramics and curing individual refractory blocks during furnace maintenance.

Holt, J. W.

Repairing cracked glass

Filing procedure consisting of machined lightweight fused-silica tiles coated with thin-layer of borosilicate glass produces homogeneous seal in thin glass. Procedure is useful in repairing glass envelopes, X-ray tub windows, Dewar flasks, and similar thin glass objects.

Helman, D. D.

Tile-bonding tool

Device applies uniform, constant, precise pressure to hold tiles in place during bonding. Tool consists of pressure bladders supported by adjustable pole. Pole can accomodate single or multiple bladders. Tiles can be flat or contoured.

Haynie, C. C.

Debonding agent for silicone-rubber adhesive

Commercially-available blend of methylene chloride in saturated trichloro-trifluoroethane is utilized as chemical debonding agent for silicone rubber adhesive bonds, without damaging bonded material.

Holt, J. W.

Hot-wire tile removal tool

Cheesecutterlike device uses electrically heated wire to slice through thermosetting embedment. Technique does not damage tile or create unwanted debris in work area.

Holt, J. W.