Engineering topics

Holst, T. L.

Publications and source records attributed to Holst, T. L..

44 records · Page 3

NASA NTRS1978

Conservative implicit schemes for the full potential equation applied to transonic flows

Implicit approximate factorization techniques (AF) were investigated for the solution of matrix equations resulting from finite difference approximations to the full potential equation in conservation form. For transonic flows, an artificial viscosity, required to maintain stability in supersonic regions, was introduced by an upwind bias of the density. Two implicit AF procedures are presented and their convergence performance is compared with that of the standard transonic solution procedure, successive line overrelaxation (SLOR). Subcritical and supercritical test cases are considered. The results indicate that the AF schemes are substantially faster than SLOR.

Holst, T. L.↗

NASA NTRS1977

Numerical solution of axisymmetric boattail flow fields with plume simulators

Turbulent separating flows over axisymmetric afterbody-boattail configurations with solid sting plume simulators are computed with a time-dependent finite-difference method to solve the compressible Navier-Stokes equations. The Reynolds stress terms are replaced with a two-layer eddy viscosity model including a relaxation formula to model the nonequilibrium effects of the separated flow. The mesh is alined with the boattail body through an analytic transformation which accommodates a wide variety of boattail geometries. Numerical results for a series of boattail geometries over a wide range of Reynolds number (140,000 to 140 million) are presented and, when possible, compared with experimental data or independent numerical results.

Holst, T. L.↗

NASA NTRS1976

Comparison of a two-dimensional shock impingement computation with experiment

Results of computations of two-dimensional viscous blunt-body flowfields with an impinging shock wave, with a time-dependent finite-difference method employed to solve the complete set of Navier-Stokes equations, are compared with experimental results. The experimental results were obtained in a 20-inch hypersonic tunnel with a planar shock impinging on the cylindrical leading edge of a fin, hence with the shock parallel to the centerline of the leading edge, so that type III and type IV interference patterns were generated. Close agreement is found. The overall effects of smoothing and grid size on the calculations are determined. A 31 x 51 mesh is adequate for wall pressure values (except in peaked regions).

Tannehill, J. C.↗

NASA NTRS1976

The relative merits of several numerical techniques for solving the compressible Navier-Stokes equations

Four explicit finite difference techniques designed to solve the time-dependent, compressible Navier Stokes equations are compared. These techniques are: (1) MacCormack, (2) modified Du Fort-Frankel, (3) modified hopscotch, and (4) Brailovskaya. The comparison was made numerically by solving the quasi-one dimensional Navier Stokes equations for the flow in a converging-diverging nozzle. Solutions with and without standing normal shock waves were computed for unit Reynolds numbers (based on total conditions) ranging from 45374 to 2269. The results indicate that all four techniques are comparable in accuracy; however, the modified hopscotch scheme is two to three times faster than the Brailovskaya and MacCormack schemes and three to six times faster than the modified Du Fort-Frankel scheme.

Holst, T. L.↗

NASA NTRS1975

Numerical computation of three-dimensional blunt body flow fields with an impinging shock

A time-marching finite-difference method was used to solve the compressible Navier-Stokes equations for the three-dimensional wing-leading-edge shock impingement problem. The bow shock was treated as a discontinuity across which the exact shock jump conditions were applied. All interior shock layer detail such as shear layers, shock waves, jets, and the wall boundary layer were automatically captured in the solution. The impinging shock was introduced by discontinuously changing the freestream conditions across the intersection line at the bow shock. A special storage-saving procedure for sweeping through the finite-difference mesh was developed which reduces the required amount of computer storage by at least a factor of two without sacrificing the execution time. Numerical results are presented for infinite cylinder blunt body cases as well as the three-dimensional shock impingement case. The numerical results are compared with existing experimental and theoretical results.

Holst, T. L.↗

NASA NTRS1975

Numerical computation of two-dimensional viscous blunt body flows with an impinging shock

Two-dimensional, viscous, blunt body flows with an impinging shock wave are computed using a time-dependent, finite-difference method to solve the complete set of Navier-Stokes equations. The bow shock wave is treated as a discontinuity, while all interior shock layer detail such as shear layers, shock waves, jets, and the wall boundary layer are automatically captured in the solution. Numerical results are presented for cases in which shock waves of different strengths are allowed to impinge on the flow field surrounding a circular cylinder resulting in different shock interference patterns. The two-dimensional results are compared qualitatively with existing three-dimensional experiments.

Tannehil, J. C.↗

NASA NTRS1974

Numerical computation of two dimensional viscous blunt body flows with an impinging shock, part 2

Two-dimensional viscous blunt body flows with an impinging shock have been computed using a time-dependent finite-difference method which solves the complete set of Navier-Stokes equations for a compressible flow. For low Reynolds number flows, the entire flow field, including the bow shock and impinging shock, has been captured in the computation. For higher Reynolds number flows, the bow shock is treated as a discontinuity across which the Rankine-Hugoniot equations are applied, while the boundary layer and interaction regions are captured as before. Using this latter shock-fitting approach, a Type III shock interaction flow field has been computed with flow conditions corresponding to the space shuttle orbiter freestream conditions at 61 km (200,000 ft).

Holst, T. L.↗

NASA NTRS1974

Numerical computation of viscous blunt body flows with a planar impinging shock

Two- and three-dimensional, viscous blunt body flows with planar impinging shocks are computed using an explicit, time-dependent, finite-difference method to solve the complete set of Navier-Stokes equations. The bow shock is treated as a discontinuity, while all interior shock layer detail such as shear layers, shock waves, jets and the wall boundary layer are automatically captured in the solution. Numerical results are presented for cases in which planar shock waves of different strengths and orientations are allowed to impinge on the flow field surroundings an infinite cylinder resulting in two- and three-dimensional shock interference patterns. The numerical results are compared with experiment.

Holst, T. L.↗