Engineering topics

Hohenemser, K. H.

Publications and source records attributed to Hohenemser, K. H..

At least 19 records

NASA NTRS1979

Parameter identification applied to analytic hingeless rotor modeling

It is known that dynamic rotor inflow has a substantial effect on rotor dynamic loads. Despite the complexity of the unsteady flow problem, simple analytical models can be made useful by identifying their parameters from transient response tests without performing flow measurements. Two analytical inflow models are studied: the first is based on an equivalent blade Lock number, the second is based on a time delayed unsteady momentum inflow. In preparation for the experimental data analysis, identifications from simulated test data and an eigenvalue analysis are performed. The experimental results show that the first analytical inflow model is accurate for rotor advance ratios of 0.4 and above. For lower advance ratios, the second inflow model provides better accuracy. Prediction studies with experimental data not used for the identification are performed to determine the accuracy of the mathematical models.

Banerjee, D.↗

NASA NTRS1978

The role of rotor impedance in the vibration analysis of rotorcraft, part 4

A method for a strongly idealized case of vertical excitation and for rolling and pitching moment excitation of a four bladed hingeless rotor on an up-focussing flexible mount is developed. The aeroelastic rotor impedances are computed directly with a finite blade element method that includes aerodynamics. The rotor impedance matrix for three or more blades is determined from the root moment impedance for a single blade by a simple multiblade transformation rule. Force and moment amplitudes transferred from the rotor to support are found to be critically dependent on the support dynamics.

Hohenemser, K. H.↗

NASA NTRS1978

Some alternative dynamic design configurations for large horizontal axis WECS

The present U.S. development effort toward large horizontal axis WECS concentrates on the configuration with two rigid blades with collective pitch variation and a yaw gear drive. Alternative configurations without yaw gear drive were considered where the rotor is either selfcentering or where the yaw angle is controlled by blade cyclic pitch inputs. A preliminary evaluation of the dynamic characteristics for these alternative design configurations is presented.

Hohenemser, K. H.↗

NASA NTRS1978

The role of rotor impedance in the vibration analysis of rotorcraft

In an improved method which retains the advantage of separate treatment of rotor and airframe, the rotor impedance is used to correct the input to the airframe. This improved method is illustrated for a strongly idealized case of vertical excitation and then for rolling and pitching moment excitation of a four bladed hingeless rotor on an up-focussing flexible mount. Contrary to the usual approach that represents aeroelastic blade motions by a series of normal blade modes in vacuum, the aeroelastic rotor impedances are computed directly with a finite blade element method that includes aerodynamics. The rotor impedance matrix for three or more blades is determined from the root moment impedance for a single blade by a simple multiblade transformation rule. Force and moment amplitudes transferred from the rotor to the support are found to be critically dependent on the support dynamics.

Hohenemser, K. H.↗

NASA NTRS1977

Unsteady hovering wake parameters identified from dynamic model tests, part 1

The development of a 4-bladed model rotor is reported that can be excited with a simple eccentric mechanism in progressing and regressing modes with either harmonic or transient inputs. Parameter identification methods were applied to the problem of extracting parameters for linear perturbation models, including rotor dynamic inflow effects, from the measured blade flapping responses to transient pitch stirring excitations. These perturbation models were then used to predict blade flapping response to other pitch stirring transient inputs, and rotor wake and blade flapping responses to harmonic inputs. The viability and utility of using parameter identification methods for extracting the perturbation models from transients are demonstrated through these combined analytical and experimental studies.

Hohenemser, K. H.↗

NASA NTRS1977

Application of system identification to analytic rotor modeling from simulated and wind tunnel dynamic test data, part 2

An introduction to aircraft state and parameter identification methods is presented. A simplified form of the maximum likelihood method is selected to extract analytical aeroelastic rotor models from simulated and dynamic wind tunnel test results for accelerated cyclic pitch stirring excitation. The dynamic inflow characteristics for forward flight conditions from the blade flapping responses without direct inflow measurements were examined. The rotor blades are essentially rigid for inplane bending and for torsion within the frequency range of study, but flexible in out-of-plane bending. Reverse flow effects are considered for high rotor advance ratios. Two inflow models are studied; the first is based on an equivalent blade Lock number, the second is based on a time delayed momentum inflow. In addition to the inflow parameters, basic rotor parameters like the blade natural frequency and the actual blade Lock number are identified together with measurement bias values. The effect of the theoretical dynamic inflow on the rotor eigenvalues is evaluated.

Hohenemser, K. H.↗

NASA NTRS1977

Finite Element Stability Analysis for Coupled Rotor and Support Systems

The effects of fuselage motions on stability and random response were analytically assessed. The feasibility of adequate perturbation models from non-linear trim conditions was studied by computer and hardware experiments. Rotor wake-blade interactions were assessed by using a 4-bladed rotor model with the capability of progressing and regressing blade pitch excitation (cyclic pitch stirring), by using a 4-bladed rotor model with hub tilt stirring, and by testing rotor models in sinusoidal up or side flow.

Hohenemser, K. H.↗

NASA NTRS1977

Identification of state variables and dynamic inflow from rotor model dynamic tests

The paper describes methods for extracting unknown state variables and parameters from dynamic rotor model tests given transient cyclic pitch stirring inputs, blade root flap-bending measurements, and the form of the dynamic rotor equations, including a rotor dynamic inflow description, when none of the physical parameters are known. A simplified version of the maximum likelihood method seems best suited for this purpose. The measurement equation error covariance matrix is assumed constant during each iteration, but updated for the subsequent iteration. A detailed analysis of the suitability of the derived techniques for studying various rotor dynamic inflow effects is provided.

Banerjee, D.↗

NASA NTRS1976

Rotor dynamic state and parameter identification from simulated forward flight transients, part 1

State and parameter identifications from simulated forward flight blade flapping measurements are presented. The transients were excited by progressing cyclic pitch stirring or by hub stirring with constant stirring acceleration. Rotor dynamic inflow models of varying degree of sophistication were used from a one parameter inflow model (equivalent Lock number) to an eight parameter inflow model. The maximum likelihood method with assumed fixed measurement error covariance matrix was applied. The rotor system equations for both fixed hub and tilting hub are given. The identified models were verified by comparing true responses with predicted responses. An optimum utilization of the simulated measurement data can be defined. From the numerical results it can be anticipated that brief periods of either accelerated cyclic pitch stirring or of hub stirring are sufficient to extract with adequate accuracy up to 8 rotor dynamic inflow parameters plus the blade Lock number from the transients.

Hohenemser, K. H.↗

NASA NTRS1976

Rotor Dynamic State and Parameter Identification from Hovering Transients

State and parameter identifications based on a form of the maximum likelihood method are applied to the problem of extracting linear perturbation models, including rotor dynamic inflow effects, from transient blade flapping measurements. The estimation method is first studied in computer simulations and then applied to cyclic pitch stirring transients generated with a four-bladed rotor model operating in hovering trim conditions. The analytical perturbation models extracted from the transient test results are compared with transient and frequency response tests not used in the state and parameter identification. The identified analytical perturbation model is also compared with a simple theory. The method that is applicable both to small scale and full scale dynamic rotor testing is being extended to perturbations from forward flight trim conditions.

Hohenemser, K. H.↗

NASA NTRS1975

Methods Studies on System Identification from Transient Rotor Tests

Some of the more important methods are discussed that have been used or proposed for aircraft parameter identification. The methods are classified into two groups: Equation error or regression estimates and Bayesian estimates and their derivatives that are based on probabilistic concepts. In both of these two groups the cost function can be optimized either globally over the entire time span of the transient, or sequentially, leading to the formulation of optimum filters. Identifiability problems and the validation of the estimates are briefly outlined, and applications to lifting rotors are discussed.

Hohenemser, K. H.↗

NASA NTRS1975

Additional experiments with a four-bladed cyclic pitch stirring model rotor, part 2 of second yearly report

The four bladed pitch stirring rotor model was used in a rotor dynamic wake survey at zero advance ratio, covering 2 deg, 5 deg and 8 deg collective pitch settings. Dynamic wake data were taken in planes .12 and .20 radii below the rotor disk and are to be compared with analytical wake data with parameters to be identified from pitch stirring transients. The model was modified to perform such transients. The instrumentation developed for this purpose is described together with the method of data acquisition and with the test procedures. The hardware and software for several data handling systems are discussed. These systems extract from pitch stirring transients the parameters of analytical dynamic rotor wake models.

Hohenemser, K. H.↗

NASA NTRS1974

Methods studies toward simplified rotor-body dynamics, part 1

This report is directed to the problem of developing an adequate but not overly complex linear flight dynamics analytical model of a rotorcraft to study stability, control, gust and random turbulence responses. Since the conventional flight dynamics analysis using quasisteady rotor derivatives is adequate for the long period modes like the phugoid mode, only short time responses are considered here, where rotor-body coupling is of importance. Thus the body motion consists of pitch, roll and vertical motion, omitting linear longitudinal and lateral and yaw perturbations. Five analytical models of varying degree of sophistication are applied to a hypothetical hingeless compound helicopter operating up to .8 rotor advance ratio. Stability and response data are obtained for the basic helicopter and for the vehicle with two simple control feedback systems.

Hohenemser, K. H.↗

NASA NTRS1974

Computer experiments in preparation of system identification from transient rotor model tests, part 2

System identification methods which can extract model rotor paramenters with reasonable accuracy from noise polluted blade flapping transient measurements were developed. Usually parameter identification requires data on the state variables, that is on deflections and on rate of deflections. The small size of rotor models makes it, however, difficult to measure more than the blade flapping deflections. For the computer experiments it was, therefore, assumed that only noisy deflection measurements are available. Parameter identifications were performed for one and two unknown parameters. Both rotating coordinates and multiblade coordinates were used. It was found that data processing with a digital filter allowed by numerical differentiation a sufficiently accurate determination of the rates of deflection and of the accelerations to obtain reasonable parameter estimates with a simple linear estimator.

Hohenemser, K. H.↗

NASA NTRS1974

Experiments with a four-bladed cyclic pitch stirring model rotor, part 3

The experimental work with the 2-bladed 16-inch diameter model rotor has been continued with a 4-bladed 16.5 inch diameter rotor capable of progressing and regressing cyclic pitch excitation (cyclic pitch stirring). Advance ratios of 0, .19 and .38 were tested at rotor speeds corresponding to non-dimensional blade natural frequencies of 1:14 and 1.19. The results are presented in the form of the first 5 Fourier components of the periodic response modulating function which for a periodic system takes the place of the complex response amplitude ratio of a constant system. In addition, the first and second harmonics of the trim response are presented. The test data are compared to analytical data without rotor wake and to the test data obtained earlier with the two-bladed rotor model of half the blade solidity ratio.

Hohenemser, K. H.↗

NASA NTRS1974

On the use of first order rotor dynamics in multiblade coordinates

This paper is directed to the question of how to represent most efficiently rotor/body coupling in a linear flight dynamics analysis. Rigid body pitch, roll and vertical motions are considered for the rotor/body coupling studies. Flapping stability limits, eigenvalues, transient responses to control step inputs, to step gusts and to random gusts are determined for a hypothetical hingeless compound helicopter operating up to .8 advance ratio. Data are obtained for the basic helicopter and for the craft with two simple control feedback systems. While complete periodic system modeling is necessary for determining flapping stability limits and vibrations, constant system modeling using first order dynamics in each of the multiblade rotor coordinates was found to be adequate for rotor-craft stability and response computations.

Hohenemser, K. H.↗

NASA NTRS1974

Computer experiments on periodic systems identification using rotor blade transient flapping-torsion responses at high advance ratio

Systems identification methods have recently been applied to rotorcraft to estimate stability derivatives from transient flight control response data. While these applications assumed a linear constant coefficient representation of the rotorcraft, the computer experiments described in this paper used transient responses in flap-bending and torsion of a rotor blade at high advance ratio which is a rapidly time varying periodic system.

Hohenemser, K. H.↗

NASA NTRS1974

Computer experiments on periodic systems identification using rotor blade transient flapping-torsion responses at high advance ratio

Computer experiments are described which used transient responses in flap-bending and torsion of a rotor blade at high advance ratio. It was found that a simple system identification method applying a linear sequential estimator also called equation of motion estimator, is suitable for this periodic system and can be used directly, if only the acceleration data are noise-polluted. In the case where noise is also present in the state-variable data, the direct application of the estimator gave poor results. However after prefiltering the data with a digital Graham filter having a cutoff frequency above the natural blade torsion frequency, the linear sequential estimator successfully recovered the parameters of the periodic coefficient analytical model.

Hohenemser, K. H.↗