Engineering Papers⌕ Search

Engineering topics

Hoggatt, J. T.

Publications and source records attributed to Hoggatt, J. T..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Hybridized polymer matrix composites

The extent to which graphite fibers are released from resin matrix composites that are exposed to fire and impact conditions was determined. Laboratory simulations of those conditions that could exist in the event of an aircraft crash and burn situation were evaluated. The effectiveness of various hybridizing concepts in preventing this release of graphite fibers were also evaluated. The baseline (i.e., unhybridized) laminates examined were prepared from commercially available graphite/epoxy, graphite/polyimide, and graphite/phenolic materials. Hybridizing concepts investigated included resin fillers, laminate coatings, resin blending, and mechanical interlocking of the graphite reinforcement. The baseline and hybridized laminates' mechanical properties, before and after isothermal and humidity aging, were also compared. It was found that a small amount of graphite fiber was released from the graphite/epoxy laminates during the burn and impact conditions used in this program. However, the extent to which the fibers were released is not considered a severe enough problem to preclude the use of graphite reinforced composites in civil aircraft structure. It also was found that several hybrid concepts eliminated this fiber release. Isothermal and humidity aging did not appear to alter the fiber release tendencies.

House, E. E.↗
NASA NTRS1979

Quality control developments for graphite/PMR15 polyimide composites materials

The problem of lot-to-lot and within-lot variability of graphite/PMR-15 prepreg was investigated. The PMR-15 chemical characterization data were evaluated along with the processing conditions controlling the manufacture of PMR-15 resin and monomers. Manufacturing procedures were selected to yield a consistently reproducible graphite prepreg that could be processed into acceptable structural elements.

Sheppard, C. H.↗
NASA NTRS1979

Development and demonstration of manufacturing processes for fabricating graphite/PMR-15 polyimide structural elements

The processing requirements for graphite/PMR-15 polyimide composites developed to demonstrate the structural integrity of polyimide composite structural elements at temperatures up to 589K (600 F) are described. Major tasks included: quality assurance development; materials and process development; specification verification; flat panel fabrication; stiffened panel fabrication; honeycomb panel fabrication; chopped fiber moldings; and demonstration component fabrication. Materials, processing, and quality assurance documents were prepared from experimentally derived data. Structural elements consisting of flat panels, corrugated stiffeners, I-beams, hat stiffeners, honeycomb panels, and chopped fiber moldings were made and tested. Property data from 219K (-65 F) to 589K (600 F) were obtained. All elements were made in a production environment. The size of each element was sufficient to insure production capability and structural component applicability. Problems associated with adhesive bonding, laminate and structural element analysis, material variability, and test methods were addressed.

Sheppard, C. H.↗
NASA NTRS1979

Development of LARC-13 adhesive systems

Various adhesive formulations were evaluated and the effects of various environments upon different titanium bond surface treatments were noted. Initial data show LARC-13 to possess good 589K (600 F) stability as compared to other high temperature stable systems.

Hoggatt, J. T.↗
NASA NTRS1979

Manufacturing processes for fabricating graphite/PMR 15 polyimide structural elements

Investigations were conducted to obtain commercially available graphite/PMR-15 polyimide prepreg, develop an autoclave manufacturing process, and demonstrate the process by manufacturing structural elements. Controls were established on polymer, prepreg, composite fabrication, and quality assurance, Successful material quality control and processes were demonstrated by fabricating major structural elements including flat laminates, hat sections, I beam sections, honeycomb sandwich structures, and molded graphite reinforced fittings. Successful fabrication of structural elements and simulated section of the space shuttle aft body flap shows that the graphite/PMR-15 polyimide system and the developed processes are ready for further evaluation in flight test hardware.

Sheppard, C. H.↗
NASA NTRS1979

Development and demonstration of manufacturing processes for fabricating graphite/PMR-15 polyimide structures

The work included establishing controls on the polymer, the prepreg, composite fabrication, and quality assurance, as well as fabrication of structural elements to demonstrate the developed materials and processes. The fabricated structures were hat sections, I-beam sections, honeycomb sandwich structures, and molded graphite-reinforced fittings. The graphite/PMR-15 polyimide system was shown to be well suited for use in the 550-600 F temperature range; the processing techniques developed were proved and found potentially useful for other commercially available systems.

Sheppard, C. H.↗
NASA NTRS1978

Applicability of thermoplastic composites for space structures

The discussion defines a thermoplastic resin and compares the structural and environmental properties and the fabrication and repairability of the thermoplastic composite with a typical epoxy composite. Low labor costs exhibited by the thermoplastic composites make them a priority consideration for use in space structure.

Hoggatt, J. T.↗
NASA NTRS1978

Reproducibility of PMR-15 graphite polymide material

Investigation was made into the reproducibility of PMR polyimide/graphite prepreg reinforcement and the influence of these variabilities on processing characteristics and final composite properties. The purpose of these investigations was to establish specification controls and limits of acceptance/rejection on incoming materials. Prepreg samples were chemically analyzed and the results compared to the processing and property results of the resulting composites. The findings from these comparisons are discussed.

Hoggatt, J. T.↗
NASA NTRS1974

Development of polyphenylquinoxaline graphite composites

This exploratory program was divided into four basic tasks. The initial phase was devoted toward investigating processing variables associated with previously developed PPO resins. These polymers were derived from p-bis(phenyl glyoxalyl)benzene reacted with 3,3'-diamino benzidine and/or 3,3',4,4'-tetramino benzophenone. Four new phenyl quinoxaline polymers were synthesized and characterized in Tasks 2 and 3. These consisted of a hydroxyl group containing PPQ synthesized from 3,3'-diamino benzidine (DAB), m-bis(phenyl glyoxal)benzene and m-bis(p'-hydroxy phenyl glyoxalyl) benzene; a cyano group containing PPQ from the reaction of DAB and p-bis(p'-cyano phenoxy phenyl glyoxalyl)benzene; an end-capped block copolymer; and a polymer from the reaction of 3,3',4,4'-tetraamino benzo phenone and m-bis(phenyl glyoxalyl)benzene. The latter two polymers were chosen for composite studies in the latter two tasks of the program. Mechanical properties of the graphite reinforced PPQ composites were determined over the temperature range of +21 C to 316 C. Flexural strengths of the HMS graphite fiber composites were in excess of 8.97 X 10 to the 8th power N/sq m (130,000 psi) at +21 C (70 F) with over 50% strength retention at +316 C.

Hoggatt, J. T.↗
NASA NTRS1974

Thin-metal lined PRD 49-III composite vessels

Filament wound pressure vessels of various configurations were evaluated for burst strength and fatigue performance. The dimensions and characteristics of the vessels are described. The types of tests conducted are explained. It was determined that all vessels leaked in a relatively few cycles (20 to 60 cycles) with failure occurring in all cases in the metallic liner. The thin liner would de-bond from the composite and buckling took place during depressurization. No composite failures or indications of impeding composite failures were obtained in the metal-lined vessels.

Hoggatt, J. T.↗
NASA NTRS1973

Development of polyphenylquinoxaline graphite composites

The potential of polyphenylquinoxaline (PPQ)/graphite composites to serve as structural material at 316 C (600 F)has been demonstrated using a block copolymer, BlCo(13), PPQ derivative. Initially, thirteen polyphenylquinoxalines were evaluated. From this work, four candidate polymers were selected for preliminary evaluation as matrices for HMS graphite fiber reinforced composites. The preliminary composite evaluation enabled selection of one of the four polymers for advanced composite preparation and testing. Using an experimentally established cure schedule for each of the four polymers, preliminary laminates of 50% resin volume content, prepared without postcure, were tested for flexure strength and modulus, interlaminar shear strength (short beam), and tensile strength and modulus at ambient temperature. A block copolymer (Bl Co 13) derived from one mole p-bis (phenylglyoxalyl) benzene, one fourth mole 3,3'-diaminobenzidine and three-fourths mole 3,3', 4,4'-tetraminobenzophenone was selected for extensive study. Tensile, flexural, and interlaminar shear values were obtained after aging and testing postcured BlCo(13) laminates at 316 C (600 F). The potential of PPQ/graphite laminates to serve as short term structural materials at temperatures up to 371 C (700 F) was demonstrated through weight loss experiments.

Hoggatt, J. T.↗
NASA NTRS1973

Development of polyphenylquinoxaline graphite composites.

The potential of polyphenylquinoxaline (PPQ)/graphite composites to serve as structural material at 316 C (600 F) has been demonstrated using a block copolymer, BICo(1:3), PPQ derivative. Initially, 13 polyphenylquinoxalines were evaluated. From this work, four candidate polymers were selected for preliminary evaluation as matrices for HMS graphite fiber reinforced composites. The preliminary composite evaluation enabled selection of one of the four polymers for advanced composite preparation and testing. Using an experimentally established cure schedule for each of the four polymers, preliminary laminates of 50% resin volume content, prepared without postcure, were tested for flexure strength and modulus, interlaminar shear strength (short beam), tensile strength, and modulus of ambient temperature. The potential of PPQ/graphite laminates to serve as short term structural materials at temperatures up to 371 C (700 F) was demonstrated through weight loss experiments.

Shdo, J. G.↗
NASA NTRS1972

Use of thin plastic films at cryogenic temperatures

Commercially available plastic film materials that remain flexible at cryogenic temperatures and resist failures caused by folds and wrinkles created during expulsion were investigated for use in expulsion bladders for liquefied gases. Compatible adhesive systems, fabrication techniques, and results of impact and dynamic loading tests are summarized.

Lark, R. F.↗
NASA NTRS1971

Development of cryogenic PRD-49-1 filament-wound tanks

A high modulus polymeric fiber was evaluated as a reinforcement for filament wound pressure vessels. Winding parameters and design data were established for the fiber with two different epoxy resin systems. Comparison was made between the performance factors of the polymeric fiber and those of S-glass and high modulus graphite vessels.

Hoggatt, J. T.↗
NASA NTRS1971

Investigation of the feasibility of developing low permeability polymeric films

The feasibility of reducing the gas permeability rate of Mylar and Kapton films without drastically effecting their flexibility characteristics at cryogenic temperatures was considered. This feasibility was established using a concept of diffusion bonding two layers of metallized films together forming a film-metal-film sandwich laminate. The permeability of kapton film to gaseous helium was reduced from a nominal ten = to the minus 9 power cc-mm/sq cm sec. cm Hg to ten to the minus 13 power cc-mm/ sq cm - sec. cm Hg with some values as low as ten to the minus 15 power cc - mm/sq cm m-sec - cm Hg being obtained. Similar reductions occurred in the liquid hydrogen permeability at -252 C. In the course of the program the permeability, flexibility and bond strength of plain, metalized and diffusion bond film were determined at +25 C, -195 C and -252 C. The cryogenic flexibility of Kapton film was reduced slightly due to the metallization process but no additional loss in flexibility resulted from the diffusion bonding process.

Hoggatt, J. T.↗
NASA NTRS1971

High performance filament wound composites for pressure vessel applications.

A new high modulus fiber was evaluated as a reinforcement for filament wound pressure vessels. Based on preliminary data it offers significant specific strength and modulus improvements over an S-glass reinforcement. Winding parameters and design data were established for the fiber with two different epoxy resin systems. NOL composite rings were evaluated for tensile strength, modulus and interlaminar shear strength at +70 F, -320 F and -423 F. Results showed that the fiber reinforced composite exhibited a specific strength of 4,100,000 inches and a specific modulus of 290,000,000 inches compared to 3,260,000 inches and 110,000,000 inches respectively for S-glass. Utilizing this data to design small filament wound pressure vessels, a performance factor of 806,000 inches was obtained experimentally with PRD 49-1 fiber compared to values of 632,000 inches and 501,000 inches for S-glass and high modulus graphite vessels, respectively.

Hoggatt, J. T.↗