Engineering topics

Hoerz, F.

Publications and source records attributed to Hoerz, F..

At least 37 records · Page 2

NASA NTRS2000

Mineralogical Studies of Experimentally Shocked Dolomite: Implications for the Outgassing of Carbonates

Common rock-forming rhombohedral carbonates - calcite and dolomite - constitute a considerable fraction of terrestrial sediments that may be shocked during hypervelocity impacts, such as during the Cretaceous-Tertiary (K/T) event or at the Haughton structure. The relatively modest temperatures needed to decompose carbonates and to release their CO2 are easily attained during such impacts. However, detailed and quantitative understanding of the CO2 release of carbonates as a function of shock stress is still the subject of controversy, as are a number of other reactions and phase transitions that were suggested for carbonates. The first devolatilization studies of carbonates in the early 1980s suggested that incipient devolatilization of calcite and/or dolomite commences at modest pressures, in the range < 10-18 GPa (amounting to 0.03-0.3% CO2 loss), with massive decarbonation (30-40% CO2 loss) occurring at shock pressure of 20 GPa and above. However, most later studies revealed that both calcite and dolomite are unexpectedly stable under shock conditions and no significant outgassing has been observed at pressures as high as 40 GPa for calcite and 60 GPa for dolomite. Despite these uncertainties, the calculations of O'Keefe and Ahrens (and others) serve to illustrate that the K/T bolide liberated sufficient CO2 that a substantial temperature increase of the global atmosphere is possible due to CO2-triggered greenhouse effects. The quantitative understanding of the devolatilization of carbonates as a function of shock stress is obviously critical to refine such calculations. Additional information is contained in the original extended abstract.

Skala, R.↗

NASA NTRS1999

Exploring the Effects of Dust Coatings and Shock Pressures on Thermal Infrared Spectra

Dust coatings on rocks obscured the underlying rock surfaces at the Mars Pathfinder landing site and made it difficult to obtain pristine visible/near-infrared reflectance spectra and chemical measurements. Such dust coatings also affect the ability of thermal infrared (TIR) spectra (such as that provided by TES and future lander (mini-TES) and orbiter multispectral imaging systems (THEMIS) to reveal accurately the mineralogy of rocks and soils. Similarly, high shock pressures from impact events cause crystalline disorder in important minerals such as pyroxene and feldspar that also affects their TIR spectra and complicates spectral interpretation of shocked impact materials. Additional information is contained in the original extended abstract.

Johnson, J. R.↗

NASA NTRS1994

Craters in aluminum 1100 targets using glass projectiles at 1-7 km/s

We report on impact experiments using soda-lime glass spheres of 3.2 mm diameter and aluminum targets (1100 series). The purpose is to assist in the interpretation of LDEF instruments and in the development of future cosmic-dust collectors in low-Earth orbit. Because such instruments demand understanding of both the cratering and penetration process, we typically employ targets with thicknesses that range from massive, infinite half-space targets, to ultrathin films. This report addresses a subset of cratering experiments that were conducted to fine-tune our understanding of crater morphology as a function of impact velocity. Also, little empirical insight exists about the physical distribution and shock-metamorphism of the impactor residues as a function of encounter speed, despite their recognized significance in the analysis of space-exposed surfaces. Soda-lime glass spheres were chosen as a reasonable analog to extraterrestrial silicates, and aluminum 1100 was chosen for targets, which among the common Al-alloys, best represents the physical properties of high-purity aluminum. These materials complement existing impact studies that typically employed metallic impactors and less ductile Al-alloys. We have completed dimensional analyses of the resulting craters and are in the process of investigating the detailed distribution of the unmelted and melted impactor residues via SEM methods, as well as potential compositional modifications of the projectile melts via electron microprobe.

Bernhard, R. P.↗

NASA NTRS1994

Shocked materials from the Dutch Peak diamictite, Utah

Evidence of shock metamorphism in the Dutch Peak diamictite in the Sheeprock Mountains, Utah, is reported. The Dutch Peak diamictite is of Proterozoic age and is a minor part of the Dutch Peak formation. A shocked sample, specimen A250, was collected during a brief visit of the Harker Canyon area of the Sheeprock Mountains. This sample consists of equant, anhedral grains of quartz, K-feldspar, and plagioclase. The crystallographic orientation of 244 lamellae systems in 106 grains was measured. It is presently difficult to evaluate the significance of this single specimen. Without additional and substantial field work, and petrographic characterization of this formation, a number of scenarios for the presence of a shocked clast and the emplacement of the entire formation remain viable.

Hoerz, F.↗

NASA NTRS1994

Experimental impacts into Teflon targets and LDEF thermal blankets

The Long Duration Exposure Facility (LDEF) exposed approximately 20 sq m of identical thermal protective blankets, predominantly on the Ultra-Heavy Cosmic Ray Experiment (UHCRE). Approximately 700 penetration holes greater than 300 micron in diameter were individually documented, while thousands of smaller penetrations and craters occurred in these blankets. As a result of their 5.7 year exposure and because they pointed into a variety of different directions relative to the orbital motion of the nonspinning LDEF platform, these blankets can reveal important dynamic aspects of the hypervelocity particle environment in near-earth orbit. The blankets were composed of an outer teflon layer (approximately 125 micron thick), followed by a vapor-deposited rear mirror of silver (less than 1000 A thick) that was backed with an organic binder and a thermal protective paint (approximately 50 to 75 micron thick), resulting in a cumulative thickness (T) of approximately 175 to 200 microns for the entire blanket. Many penetrations resulted in highly variable delaminations of the teflon/metal or metal/organic binder interfaces that manifest themselves as 'dark' halos or rings, because of subsequent oxidation of the exposed silver mirror. The variety of these dark albedo features is bewildering, ranging from totally absent, to broad halos, to sharp single or multiple rings. Over the past year experiments were conducted over a wide range of velocities (i.e., 1 to 7 km/s) to address velocity dependent aspects of cratering and penetrations of teflon targets. In addition, experiments were performed with real LDEF thermal blankets to duplicate the LDEF delaminations and to investigate a possible relationship of initial impact conditions on the wide variety of dark halo and ring features.

Hoerz, F.↗

NASA NTRS1994

Morphology of meteoroid and space debris craters on LDEF metal targets

We measured the depths, average diameters, and circularity indices of over 600 micrometeoroid and space debris craters on various metal surfaces exposed to space on the Long Duration Exposure Facility (LDEF) satellite, as a test of some of the formalisms used to convert the diameters of craters on space-exposed surfaces into penetration depths for the purpose of calculating impactor sizes or masses. The topics covered include the following: targe materials orientation; crater measurements and sample populations; effects of oblique impacts; effects of projectile velocity; effects of crater size; effects of target hardness; effects of target density; and effects of projectile properties.

Love, S. G.↗

NASA NTRS1994

Penetration experiments in aluminum and Teflon targets of widely variable thickness

The morphologies and detailed dimensions of hypervelocity craters and penetration holes on space-exposed surfaces faithfully reflect the initial impact conditions. However, current understanding of this postmortem evidence and its relation to such first-order parameters as impact velocity or projectile size and mass is incomplete. While considerable progress is being made in the numerical simulation of impact events, continued impact simulations in the laboratory are needed to obtain empirical constraints and insights. This contribution summarizes such experiments with Al and Teflon targets that were carried out in order to provide a better understanding of the crater and penetration holes reported from the Solar Maximum Mission (SMM) and the Long Duration Exposure Facility (LDEF) satellites. A 5-mm light gas gun was used to fire spherical soda-lime glass projectiles from 50 to 3175 microns in diameter (D(sub P)), at a nominal 6 km/s, into Al (1100 series; annealed) and Teflon (Teflon(sup TFE)) targets. Targets ranged in thickness (T) from infinite halfspace targets (T approx. equals cm) to ultrathin foils (T approx. equals micron), yielding up to 3 degrees of magnitude variation in absolute and relative (D(sub P)/T) target thickness. This experimental matrix simulates the wide range in D(sub P)/T experienced by a space-exposed membrane of constant T that is being impacted by projectiles of widely varying sizes.

Hoerz, F.↗

NASA NTRS1994

The use of silica aerogel to collect interplanetary dust in space

We report on impact experiments to evaluate the suitability of silica aerogel as a capture medium for interplanetary dust particles in space. The structure of silica aerogel is such that even micrometer-sized hypervelocity particles may sense it as a target of very low density; consequently shock stresses and temperatures due to impact should be minimized. We performed impact experiments in a light gas gun that employed projectiles manufactured from forsterite, pyrrhotite, and calcite. From these experiments we have developed techniques that will permit the successful extrication of interplanetary dust particles from aerogel. We note a rough correlation between increasing particle penetration lengths and decreasing aerogel density, and there is a poor correlation of track lengths with impact velocity at laboratory-attainable velocities of 5-7 km/s. We conclude that aerogel track length should not be used even as (crude) velocity indicators. Transmission electron microscope studies show the re covered particulate residues are encased in melted silica aerogel, which possibly protects the residue from some impact damage. Individual minerals within interplanetary dust are expected to exhibit differential survival, and may be vaporized, melted, dehydrated, or structurally reordered. However, some mineral grains should successfully be captured in an unmelted state at encounter velocities less than 8 km/s.

Zolensky, Michael E.↗

NASA NTRS1993

Composition and modal frequencies of hypervelocity particles less than 1 millimeter in diameter in low-Earth orbit

We have continued to systematically analyze the projectile residues associated with hypervelocity impact features on the surfaces of the 'Chemistry of Micrometeoroid Experiment' (CME) that was in low-Earth orbit (LEO) for 5.7 years aboard the Long Duration Exposure Facility (LDEF). Last year we reported on the systematic analysis, via SEM-EDX methods, of all craters greater than 20 microns in diameter on the collectors from LDEF's trailing edge and approximately 200 craters greater than 75 microns in diameter from the aluminum 1100 substrates from the forward-facing surfaces. This latter group represents less than 20 percent of all craters on the A11 collectors, because the particle flux is substantially higher for the forward-facing orientations relative to the trailing-edge surfaces. To date, we have analyzed some 600 craters on the A11 aluminum collectors, yet this report summarizes only 400 features, because not all of the results have been completely reduced and entered into our database.

Bernhard, R. P.↗

NASA NTRS1993

Impact penetration experiments in teflon targets of variable thickness

Approximately 20.4 sq m of Teflon thermal blankets on the nonspinning Long Duration Exposure Facility (LDEF) were exposed to the orbital debris and micrometeoroid environment in low-Earth orbit (LEO) for approximately 5.7 years. Each blanket consisted of an outer layer (approximately 125 micron thick) of FEP Teflon that was backed by a vapor-deposited metal mirror (Inconel; less than 1 micron thick). The inner surface consisted of organic binders and Chemglaze thermal protective paint (approximately 50 micron thick) resulting in a somewhat variable, total blanket thickness of approximately 180 to 200 microns. There was at least one of these blankets, each exposing approximately 1.2 sq m of surface area, on nine of LDEF's 12 principal pointing directions, the exceptions being Rows 3, 9, and 12. As a consequence, these blankets represent a significant opportunity for micrometeoroid and debris studies, in general, and specifically they provide an opportunity to address those issues that require information about pointing direction (i.e., spatial density of impact events as a function of instrument orientation). During deintegration of the LDEF spacecraft at KSC, all penetration holes greater than or equal to 300 micron in diameter were documented and were recently synthesized in terms of spatial density as a function of LDEF viewing direction by. The present report describes ongoing cratering and penetration experiments in pure Teflon targets, which are intended to establish the relationships between crater or penetration-hole diameters and the associated projectile dimensions at laboratory velocities (i.e., 6 km/s). The ultimate objective of these efforts is to extract reliable mass-frequencies and associated fluxes of hypervelocity particles in LEO.

Hoerz, F.↗

NASA NTRS1992

Suitability of silica aerogel as a capture medium for interplanetary dust

Impact experiments using silica aerogel as a deceleration and capture medium for interplanetary dust are reported. A rough correlation is noted between increasing particle track lengths and decreasing aerogel density, and there is a poor correlation of track lengths with impact velocity at laboratory attainable velocities of 5-7 km/s. It is concluded that aerogel track lengths should not be used as velocity indicators. Chemical analyses are also reported of aerogel samples used in this study in order to assess the risks concerning contamination of interplanetary dust particles by the silica aerogel capture medium. It is demonstrated that this material is impressively clean.

Barrett, R. A.↗

NASA NTRS1987

Impact cratering in reduced-gravity environments: Early experiments on the NASA KC-135 aircraft

Impact experimentation on the NASA KC-135 Reduced-Gravity Aircraft was shown to be possible, practical, and of considerable potential use in examining the role of gravity on various impact phenomena. With a minimal facility, crater dimensional and growth-times were measured, and have demonstrated both agreement and disagreement with predictions. A larger facility with vacuum capability and a high-velocity gun would permit a much wider range of experimentation.

Cintala, Mark J.↗

NASA NTRS1986

Trajectory determinations and collection of micrometeoroids on the space station. Report of the Workshop on Micrometeorite Capture Experiments

Summaries of papers presented at the Workshop on Micrometeorite Capture Experiments are compiled. The goals of the workshop were to define the scientific objectives and the resulting performance requirements of a potential Space Station facility and to identify the major elements of a coherent development program that would generate the desired capabilities within the next decade. Specific topics include cosmic dust and space debris collection techniques, particle trajectory and source determination, and specimen analysis methods.

Hoerz, F.↗

NASA NTRS1985

Measurements of the elemental and isotopic composition of interplanetary dust collected on LDEF

A passive interplanetary dust collection experiment, currently in orbit aboard the Long Duration Exposure Facility, is described. The collectors, germanium target plates covered by metallized Mylar foils, are designed for secondary ion mass spectrometry measurements of the elemental and isotopic compositions of residues resulting from micrometeoroid (greater than 10 to the -10th grams) impacts. Impact simulation experiments have demonstrated the validity of the collection concept. Quantitative elemental analyses are complicated by the nonuniform distribution of projectile-derived elements.

Fechtig, H.↗

NASA NTRS1984

The chemistry of micrometeoroids (A0187-1)

The prime objective of this experiment is to obtain chemical analyses of a statistically significant number of micrometeoroids. These data will then be compared with the chemical composition of meteorites. Secondary objectives of the experiment relate to density, shape, mass frequency, and absolute flux of micrometeorids as deduced from detailed crater geometrics (depth) diameter, and plane shape, and number of total events observed.

Hoerz, F.↗

NASA NTRS1979

Shock metamorphism of granulated lunar basalt

The paper deals with an extensive series of shock-recovery experiments performed on both nonporous crystalline basalt and its granulated and sieved counterpart to study the role of porosity and grain size in shock motomorphic effects under otherwise identical conditions. Shocked samples are compared with unshocked starting material in terms of textural and mineralogical modifications attributable to shock. A comparative petrographic and chemical characterization is presented of pulverized and sieved lunar basalt 75035 shocked between 6 and 75 GPa in comparison with holocrystalline disks of the same basalts shocked in 10 earlier experiments. Specifically, a petrographic classification of shock features is given, along with an estimation of relative amounts of shock glasses and a chemical characterization of shock glasses in each shocked granular basalt.

Schaal, R. B.↗

NASA NTRS1978

X-ray diffractometer studies of shocked materials

This study explores the utility of X-ray diffractometer scans for determination of shock pressure histories of geological materials from meteorite impact sites. The technique is based on quantification of increased crystal lattice disorder with increasing shock pressure as expressed by decreasing diffraction peak amplitude and pronounced line-broadening caused by decreasing mosaic domain size and increasing strain. The ratio of peak height (PH) to half width (HW) decreases systematically with increasing shock pressure. Data are given for experimentally shocked quartz, feldspars, pyroxene and olivine along with data for granitic materials from the Piledriver nuclear event and from the Ries Crater, Germany. Although the technique in principle may be capable of yielding relatively accurate pressure determinations, its application to naturally shocked materials may be severely limited.

Hanss, R. E.↗

NASA NTRS1978

How thick are lunar mare basalts

It is argued that De Hon's estimates of the thickness of lunar mare basalts, made by analyzing 'ghost' craters on mare surfaces, were inflated as the result of the crater morphometric data of Pike (1977) to reconstruct rim heights of degraded craters. Crater rim heights of 82 randomly selected highland craters of various states of degradation were determined, and median rim height was compared to that of corresponding fresh impact structures. Results indicate that the thickness estimates of De Hon may be reduced by a factor of 2, and that the total volume of mare basalt produced throughout lunar history could be as little as 1-2 million cubic kilometers. A survey of geochemical and petrographic evidence indicates that lateral transport of regolith components over distances of much greater than 10 km is relatively inefficient; it is suggested that vertical mixing of a highland substrate underlying the basaltic fill may have had a primordial role in generating the observed mare width distributions and high concentrations of exotic components in intrabasin regoliths.

Hoerz, F.↗