Reestablishing the Supply of Plutonium-238
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Hobbs, Randy W.
Explore the source record for details and available documents.
Oak Ridge National Laboratory is recovering the US 238 Pu production capability and the first step in the process has been to evaluate the performance of a 237 Np target cermet pellet encased in an aluminum clad. The process proceeded in 3 steps; the first step was to irradiate capsules of single pellets composed of NpO 2 and aluminum power to examine their shrinkage and gas release. These pellets were formed by compressing sintered NpO 2 and aluminum powder in a die at high pressure followed by sintering in a vacuum furnace. Three temperatures were chosen for sintering the solution precipitated NpO 2 power used for pellet fabrication. The second step was to irradiate partial targets composed of 8 pellets in a semi-prototypical arrangement at the two best performing sintering temperatures to determine which temperature gave a pellet that performed the best under the actual planned irradiation conditions. The third step was to irradiate ~50 pellets in an actual target configuration at design irradiation conditions to assess pellet shrinkage and gas release, target heat transfer, and dimensional stability. The higher sintering temperature appeared to offer the best performance after one cycle of irradiation by having the least shrinkage, thus keeping the heat transfer gap between the pellets and clad small minimizing the pellet operating temperature. The final result of the testing was a target that can meet the initial production goals, satisfy the reactor safety requirements, and can be fabricated in production quantities. The current focus of the program is to verify that the target can be remotely dissembled, the pellets dissolved, and the 238 Pu recovered. Tests are being conducted to examine these concerns and to compare results to code predictions. Once the performance of the full length targets has been quantified, the pellet 237 Np loading will be revisited to determine if it can be increased to increase 238 Pu production.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The Oak Ridge National Laboratory (ORNL)is developing technology to produce plutonium-238 for the National Aeronautics and Space Administration (NASA) as a power source material for powering vehicles while in deep-space[1]. The High Flux Isotope Reactor (HFIR) of ORNL has been utilized to perform test irradiations of incapsulated neptunium oxide (NpO2) and aluminum powder bare pellets for purposes of understanding the performance of the pellets during irradiation[2]. Post irradiation examinations (PIE) are currently underway to assess the effect of temperature, thermal expansion, swelling due to gas production, fission products, and other phenomena
The Global Nuclear Energy Partnership (GNEP) is proposing to develop a sodium-cooled fast-spectrum reactor (SFR) to transmute and consume actinides from discharged nuclear fuel. To meet performance objectives, new and advanced fuels and targets need to be developed. The fuels to be irradiated include metal and oxide mixed actinides (U-Np-Pu-Am-Cm); for the target concept, Am-Cm has been considered. A significant part of the development process is the irradiation of the fuel and cladding in a prototypic fast reactor environment to determine the performance under irradiation. Analysis results are presented in this paper for a fast-neutron irradiation facility design based on the large fast neutron flux available in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) combined with the use of a strongly-absorbing thermal neutron shield. Several designs were assessed; the preferred concept consists of a three-pin design with an europium oxide thermal neutron shield, to be situated in the HFIR flux trap. Analyses show that this design could provide a fast to thermal neutron flux ratio greater than 400, a fast neutron flux larger than 1 x 10{sup 15} n/cm{sup 2} {center_dot} s, and with an acceptable impact on HFIR operation. This design feasibly will be a relatively low-cost near-term facility that meets the requirements for fast fuel irradiation.
A concept for a fast spectrum irradiation facility has been developed for insertion in the High Flux Isotope Reactor at Oak Ridge National Laboratory. The design is based on the very large fast flux that is available in this reactor combined with the use of a strongly-absorbing thermal neutron shield. The preferred concept from the several considered consists of a three-pin design surrounded by a Eu{sub 2}O{sub 3} thermal neutron shield located in the reactor flux trap. Preliminary analyses showed that this concept can provide a fast flux larger than 1x10{sup 15} n/cm{sup 2}{center_dot}s and a fast-to-thermal flux ratio greater than 300 while having an acceptable impact on the HFIR operation. Additional analyses are necessary to confirm that this design is feasible and meets the requirements for fast fuel irradiation. If the design proves to be suitable, it can provide a relatively low-cost, near-term capability.
Abstract - The Global Nuclear Energy Partnership (GNEP) is proposing to develop a sodium-cooled fast-spectrum reactor (SFR) to transmute and consume actinides from spent nuclear fuel. The proposed fuels include metal and oxide mixed actinides (U-Np-Pu-Am-Cm) as well as target concepts with perhaps only Am-Cm. The High Flux Isotope Reactor was built for the purpose of transmuting plutonium to various higher actinides including Am, Cm, and Cf. Since a fast-spectrum irradiation facility does not exist in the United States, HFIR can fulfill a first step in the GNEP mission; that being to establish a near-term capability to irradiate materials in a fast neutron spectrum in addition to efforts to gain access to international facilities through partnering arrangements. Modifications to the HFIR central target region to accomplish this goal are described. A second on-going project for HFIR is to design capsules and installation tools and procedures to irradiate short rods of innovative nuclear fuel types and cladding materials under prototypic LWR operating conditions at an accelerated rate relative to expected reactor performance. This second proposal would be for a facility representative of thermal reactor conditions rather than the GNEP concept. In order to maintain power densities within the fuel at levels normally seen by LWR reactors, an entirely new experiment and test capsule design will be needed than has been available in the past.
The Global Nuclear Energy Partnership (GNEP) is proposing to develop a sodium-cooled fast-spectrum reactor (SFR) to transmute and consume actinides from discharged nuclear fuel. To meet performance objectives, new and advanced fuels and targets need to be developed. The fuels to be irradiated include metal and oxide mixed actinides (U-Np-Pu-Am-Cm); for the target concept, Am-Cm has been considered. A significant part of the development process is the irradiation of the fuel and cladding in a prototypic fast reactor environment to determine the performance under irradiation. Analysis results are presented in this paper for a fast-neutron irradiation facility design based on the large fast neutron flux available in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) combined with the use of a strongly-absorbing thermal neutron shield. Several designs were assessed; the preferred concept consists of a three-pin design with an europium oxide thermal neutron shield, to be situated in the HFIR flux trap. Analyses show that this design could provide a fast to thermal neutron flux ratio greater than 400, a fast neutron flux larger than 1x1015 n/cm2s, and with an acceptable impact on HFIR operation. This design feasibly will be a relatively low-cost near-term facility that meets the requirements for fast fuel irradiation.