Engineering topics

Henkelman, Graeme

Publications and source records attributed to Henkelman, Graeme.

26 records · Page 2

DOE OSTI2020

Highly reversible oxygen redox in layered compounds enabled by surface polyanions

Oxygen-anion redox in lithium-rich layered oxides can boost the capacity of lithium-ion battery cathodes. However, the over-oxidation of oxygen at highly charged states aggravates irreversible structure changes and deteriorates cycle performance. Here, we investigate the mechanism of surface degradation caused by oxygen oxidation and the kinetics of surface reconstruction. Considering Li 2 MnO 3 , we show through density functional theory calculations that a high energy orbital (lO 2p’ ) at under-coordinated surface oxygen prefers over-oxidation over bulk oxygen, and that surface oxygen release is then kinetically favored during charging. We use a simple strategy of turning under-coordinated surface oxygen into polyanionic (SO 4 ) 2- , and show that these groups stabilize the surface of Li 2 MnO 3 by depressing gas release and side reactions with the electrolyte. Experimental validation on Li 1.2 Ni 0.2 Mn 0.6 O 2 shows that sulfur deposition enhances stability of the cathode with 99.0% capacity remaining (194 mA h g -1 ) after 100 cycles at 1 C. Our work reveals a promising surface treatment to address the instability of highly charged layered cathode materials.

25 ENERGY STORAGE↗

DOE OSTI2020

Hydrogen desorption from the surface and subsurface of cobalt

The influence of coverage on the diffusion of hydrogen into the subsurface of cobalt was studied using density functional theory (DFT) and temperature programmed desorption (TPD). DFT calculations show that as the hydrogen coverage on Co(0001) increases, the barrier for hydrogen diffusion into the bulk decreases by 20%. Additionally, subsurface hydrogen on a hydrogen covered surface was found to be more stable when compared to a clean cobalt surface. To test these theoretical findings experimentally, excited hydrogen was used in an ultra-high vacuum environment to access higher hydrogen coverages. Here, our TPD studies showed that at high hydrogen coverages, a sharp low temperature feature appeared, indicating the stabilization of subsurface hydrogen. Further DFT calculations indicate that this sharp low temperature feature results from associative hydrogen desorption from a hydrogen saturated surface with a population of subsurface hydrogen. Microkinetic modelling was used to model the TPD spectra for hydrogen desporption from cobalt with and without subsurface hydrogen, showing reasonable agreement with experiment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Identification of Active Sites of Pure and Nitrogen-Doped Carbon Materials for Oxygen Reduction Reaction Using Constant-Potential Calculations

Nitrogen-doped carbon materials are promising metal-free catalysts for the electrochemical oxygen reduction reaction (ORR). A better theoretical understanding on the nature of the active site(s) would help further optimization of their ORR activity. Although quantum mechanical calculations have been widely employed to elucidate the active sites over various catalysts, these calculations are typically done assuming constantcharge conditions rather than the experimentally relevant constant-potential conditions. In this study, we employ the double-reference method to simulate the energetics of the ORR over pure and N-doped carbon materials under constant-potential conditions. We demonstrate that constant-potential calculations enable more accurate theoretical predictions, comparing well with existing experiments. Our key findings are (1) the zigzag edge of pure graphite is highly active for ORR, (2) the pyridinic N-doped armchair edge is highly active for ORR in alkaline media but not in acid, and (3) graphitic N can donate electrons to pyridinic N to enhance the ORR activity. Furthermore, these fundamental insights provide guidelines for the design of better carbonbased ORR catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Effect of TiO x Substrate Interactions on the Electrocatalytic Oxygen Reduction Reaction at Au Nanoparticles

Here, we report a robust model for studying electrocatalytic reactions at metal nanoparticles (NPs) in contact with metal oxide surfaces. The metal oxide layer (TiO x ) is prepared by atomic layer deposition, and it is sufficiently thin that it does not hinder electron transfer from the underlying conductive electrode to the supported AuNP electrocatalysts. In advance of the experiments, density functional theory (DFT) predicted that direct contact between AuNPs and TiO x would lead to enhanced activity for the oxygen reduction reaction (ORR). DFT attributes the observed ORR enhancement to partial charge transfer from oxygen vacancies within the TiO x film to the supported AuNPs and hence formation of anionic Au species. The experimental findings are in near quantitative agreement with the DFT results. Specifically, compared to isolated AuNPs, decreases of ~ 100 and ~ 50 mV in the ORR onset potential are observed experimentally for AuNPs supported on TiO 1.9 and TiO 2.0 films, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Testing the predictive power of theory for Pd x Ir (100-x) alloy nanoparticles for the oxygen reduction reaction

Here, density functional theory (DFT) calculations of O and OH binding energies on triatomic surface ensembles of Pd x Ir (100-x) nanoalloys successfully predicted the overall trend in experimental oxygen reduction reaction (ORR) activity as a function of nanoparticle (NP) composition. Specifically, triatomic Pd 3 ensembles were found to possess optimal O and OH binding energies and were predicted to be highly active sites for the ORR, rivaling that of Pt(111). However, DFT calculations suggest that the O binding energy increases at active sites containing Ir, thereby decreasing ORR activity. Pd x Ir (100-x) nanoalloys were synthesized using a microwave-assisted method and their activity towards the ORR was tested using rotating disk voltammetry (RDV). As predicted, the bimetallic electrocatalysts exhibited worse catalytic activity than the Pd-only NPs. The strong qualitative correlation between the theoretical and experimental results demonstrates that the activity of individual active sites on the surface of NPs can serve as a proxy for overall activity. This is a particularly useful strategy for applying DFT calculations to electrocatalysts that are too large for true first-principle analysis.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Sulfur Loading and Speciation Control the Hydrophobicity, Electron Transfer, Reactivity, and Selectivity of Sulfidized Nanoscale Zerovalent Iron

Sulfidized nanoscale zerovalent iron (SNZVI) is a promising material for groundwater remediation. However, the relationships between sulfur content and speciation and the properties of SNZVI materials are unknown, preventing rational design. Here, the effects of sulfur on the crystalline structure, hydrophobicity, sulfur speciation, corrosion potential, and electron transfer resistance are determined. Sulfur incorporation extended the nano-Fe 0 BCC lattice parameter, reduced the Fe local vacancies, and lowered the resistance to electron transfer. Impacts of the main sulfur species (FeS and FeS 2 ) on hydrophobicity (water contact angles) are consistent with density functional theory calculations for these FeS x phases. These properties well explain the reactivity and selectivity of SNZVI during the reductive dechlorination of trichloroethylene (TCE), a hydrophobic groundwater contaminant. Controlling the amount and speciation of sulfur in the SNZVI made it highly reactive (up to 0.41 L m -2 d -1 ) and selective for TCE degradation over water (up to 240 moles TCE per mole H 2 O), with an electron efficiency of up to 70%, and these values are 54-fold, 98-fold, and 160-fold higher than for NZVI, respectively. These findings can guide the rational design of robust SNZVI with properties tailored for specific application scenarios.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Cobalt Metal–Cobalt Carbide Composite Microspheres for Water Reduction Electrocatalysis

Microspheres of cobalt metal–cobalt carbide (Co–Co x C, Co x C: Co 2 C and Co 3 C) composite with carbon shells were prepared via an OH – - and Cl – -assisted polyol method and explored for electrocatalytic activity and stability for the hydrogen evolution reaction (HER) in acidic media. From our transmission electron microscopy observations, the outermost surfaces of the as-prepared Co–Co x C composites were primarily covered with Co 2 C crystallites. Our best performing electrocatalyst exhibited superior HER activity with an overpotential of 78 mV to reach a current density of -10 mA·cm –2 , a Tafel slope of 87.8 mV·dec –1 , and 1 h of electrode durability. We show that this excellent HER performance is primarily due to the superior intrinsic activity of Co 2 C, as well as the high electrical conductivity resulting from the inclusion of cobalt metal and the presence of graphitic carbon shells in and on the composite, respectively. Using both computational and experimental approaches, we determine here that the carbon-rich cobalt carbide (Co 2 C) phase is more favorable for the HER than the carbon-poor phase (Co 3 C).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Low temperature dissociation of CO on manganese promoted cobalt(poly)

We observe that metallic manganese alloyed with polycrystalline cobalt promotes the dissociation of CO. Increasing coverages of Mn on Co facillitate stronger molecular CO binding energies and stronger C(ad) + O(ad) binding energies. These findings show the role of metallic manganese in promoting model Co Fischer–Tropsch catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗